| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on
the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY
on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts
for the muxed PHY won't work, therefore delete the "interrupts" property on
the devices where the PHY muxing feature is in use.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
|
| |
|
|
|
|
|
|
|
|
| |
The previous NVMEM eeprom conversions[1][2] left a lot of partition
labels that were no longer used. They can be removed now.
[1] https://github.com/openwrt/openwrt/pull/13584
[2] https://github.com/openwrt/openwrt/pull/13587
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
|
| |
|
|
|
|
|
|
|
| |
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
| |
nvmem-layout allows removal
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
| |
|
|
|
|
| |
Allows replacing mac-address-increment with mac-base.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
| |
|
|
|
|
|
| |
This patch converts MT7613 and MT7615 WiFi calibration data to NVMEM
format. The EEPROM size is 0x4da8.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2
pins are available. This achieves 2 Gbps total bandwidth to the CPU using
the second RGMII.
The ports called "wan" are muxed where possible. On a minority of devices,
this is not possible. Those cases:
mt7621_ampedwireless_ally-r1900k.dts: lan3
mt7621_ubnt_edgerouter-x.dts: eth0
mt7621_gnubee_gb-pc1.dts: ethblue
mt7621_linksys_re6500.dts: lan1
mt7621_netgear_wac104.dts: lan4
mt7621_tplink_eap235-wall-v1.dts: lan0
mt7621_tplink_eap615-wall-v1.dts: lan0
mt7621_ubnt_usw-flex.dts: lan1
The "wan" port is just what the vendor designated on the board/plastic
chasis of the device. On a technical level, there is no difference between
a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer
connecting to WAN via the port described above for these devices to benefit
the feature brought with this patch.
mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks
like it should, because the rgmii2 pins are wired to unused components.
Tested on a range of devices documented on the GitHub PR.
Link: https://github.com/openwrt/openwrt/pull/10238
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
|
|
|
Add support for ipTIME A3002MESH.
Hardware:
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: XMC XM25QH128AHIG (SPI-NOR 16MB)
- WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in)
- UART: [GND, RX, TX, 3.3V] (57600 8N1, J4)
MAC addresses:
| interface | MAC | source | comment
|-----------|-------------------|----------------|----------
| LAN | 70:XX:XX:5X:XX:X3 | |
| WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 |
| WLAN 2G | 72:XX:XX:4X:XX:X0 | |
| WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4 |
| | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown
| | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown
- WLAN 2G MAC address is not the same as stock firmware since OpenWrt
uses LAN MAC address with local bit sets.
Installation:
1. Flash initramfs image. This can be done using stock web ui or TFTP
2. Connect to OpenWrt with an SSH connection to 192.168.1.1
3. Perform sysupgrade with sysupgrade image
Revert to stock firmware:
- Flash stock firmware via OEM TFTP Recovery mode
- Perform sysupgrade with stock image
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
[wrap/rephrase commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|