aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAge
* ramips: mt7621-dts: describe switch PHYs and adjust PHY muxingArınç ÜNAL2024-05-01
| | | | | | | | | | | | | | | | | | | | | | | | Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO bus the switch listens on. The PHY muxing feature makes use of this. This is problematic as the PHY may be attached before the switch is initialised, in which case, the PHY will fail to be attached. Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on the MDIO bus of the switch on the device tree. When the PHY is described this way, the switch will be initialised first, then the switch MDIO bus will be registered. Only after these steps, the PHY will be attached. Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts for the muxed PHY won't work, therefore delete the "interrupts" property on the devices where the PHY muxing feature is in use. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621-dts: remove incorrect ethphy4 node for WAVLINK WL-WN573HX1Arınç ÜNAL2024-05-01
| | | | | | | The ethernet-phy@4 node doesn't exist for WAVLINK WL-WN573HX1. Remove it and the duplicate gmac0 node. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621-dts: do not modify ethernet node for MeiG SLT866Arınç ÜNAL2024-05-01
| | | | | | | | | | Currently, the pinctrl-0 property on the ethernet node is modified to exclude the rgmii1 and rgmii2 pin groups to be claimed with rgmii1 and rgmii2 functions, respectively. Remove the modification of this property as we need these pin groups to be claimed with the said functions for this device. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: Add support for D-Link DIR-3040 A1Vince McKinsey2024-04-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the A1 hardware revision of the DIR-3040. It is an exact copy of the DIR-3060 save for some cosmetic changes to the housing. Even going so far as having the same FCC ID. Hardware specification: SoC: MediaTek MT7621AT Flash: Winbond W29N01HVSINA 128MB RAM: Micron MT41K128M16JT-125 256MB Ethernet: 5x 10/100/1000 Mbps WiFi1: MT7615DN 2.4GHz N 2x2:2 WiFi2: MT7615DN 5GHz AC 2x2:2 WiFi3: MT7615N 5GHz AC 4x4:4 Button: WPS, Reset Flash instructions: OpenWrt can be installed via D-Link Recovery GUI: NOTE: Seems to only work in Firefox on Windows. Tried with Chrome on Windows, Firefox in Linux, and Chromium in Linux. None of these other browsers worked. 1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable. 2. Give it ~30 seconds, to boot the recovery mode GUI 3. Connect your client computer to LAN1 of the device 4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0. 5. Call the recovery page for the device at http://192.168.0.1/ 6. Use the provided emergency web GUI to upload and flash a new firmware to the device Thanks to @Lucky1openwrt and @iivailo for creating the DIR-3060 DTS file and related changes, so it was possible for me to adapt them to the DIR-3040, build images, test and fix minor issues. MAC Addresses: | use | address | example | | --- | --- | --- | | LAN | label | f4:*:61 | | WAN | label + 4 | f4:*:65 | | WI1/2g | label + 2 | f4:*:63 | | WI1/5g | label + 1 | f4:*:62 | | WI2/5g | label + 3 | f4:*:64 | The label MAC address was found in Factory, 0xe000 Checklist: ✓ nand ✓ ethernet ✓ button ✓ wifi2g ✓ wifi5g ✓ wifi5g ✓ mac ✓ led Signed-off-by: Vince McKinsey <vincemckinsey@gmail.com>
* ramips: add support for TP-Link EC220-G5 v2Mieczyslaw Nalewaj2024-04-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EC220-G5 v2 is a dual band router with 4 GbE ports Advertised as AC1200 for its 867Mbps (2x2) 5GHz band and 300 Mbps (2x2) 2.4GHz band. Specs: - SoC: MediaTek MT7620A - Ethernet: 4x GbE ports (Realtek RTL8367S) - Wireless 2.4GHz: MediaTek MT7620A - Wireless 5GHz: MediaTek MT7612E - RAM: 64MiB - ROM: 8MiB (W25Q64BV) - 2 Buttons (WPS and reset) - 7 LEDs Flash instructions via serial console: 1. Rename the factory.bin to to test.bin 2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin 3. connect your device to the LAN port 4. power up the router and press 4 on the console to stop the boot process. 5. enter the following commands on the router console tftp 0x80060000 test.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset Flash instructions via TFTP: 1. Update orginal firmware of the router to the latest one. 2. Rename openwrt-ramips-mt7620-tplink_ec220-g5-v2-squashfs-tftp-recovery.bin to tp_recovery.bin 3. Change computer IP to 192.168.0.66 4. Run TFTP serwer 5. Start the router with the reset button pressed, the file will be automatically downloaded and after a while the router will restart. 6. After updating, set your computer's IP to DHCP Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: mt7620a_tplink_archer.dtsi rename to mt7620a_tplink_8m.dtsiMieczyslaw Nalewaj2024-04-13
| | | | | | Change the name mt7620a_tplink_archer.dtsi to mt7620a_tplink_8m.dtsi because it will also be a base for TP-Link non-Archer routers. Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: TP-Link Archer C2 v1: simplification of the dts definitionMieczyslaw Nalewaj2024-04-13
| | | | | | Import from the mt7620a_tplink_archer.dtsi file and thus simplify the rest of the definition. Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: mt7620a_tplink_archer.dtsi - remove unnecessary nvmem-cells definitionsMieczyslaw Nalewaj2024-04-13
| | | | | | Remove unnecessary nvmem-cells definitions that are being redefined anyway. Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: add support for BOLT BL100Radito Wahyu2024-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BL100 is a router made by Bolt by a provider in Indonesia The original firmware created using Mediatek SDK and kernel 2.6.36 - Chipset: MediaTek MT7620A ver 2, eco 6 - RAM: 64 MB - Bootloader: U Boot - Flash: Winbond W25Q128BV (16 MB) - Ports: 2x 10/100 Ethernet, 1x RJ-11 VoIP - Modem: Qualcomm LTE B40 (2300 Mhz) VID:05c6 PID:9026 - Wireless: Internal MT7620A (2.4 Ghz) & Mediatek MT76x2E (5.8 Ghz) - Switch: MediaTek MT7620A built-in 5-port 10/100M switch - Voltage: DC 12V 1A - Antenna Port: 2x External Antenna, 2 LTE U.FL, 2 WiFi U.FL - Serial Port: Yes, 3.3 V TTL, Baud 57600 8N1 - Buttons: Reset and WPS - LED: 15 Total - 4 blue lte, 2 red lte, 1 reset, 1 power. - 1 wps, 1 voip, 1 wlan2, 1 wlan5, 1 lan, 1 wan, 1 wlan. Installation via stock firmware 1. Unlock Telnet access by downloading the backup .tar.gz file 2. Change the Telnet configuration to LAN_Telnet=1 3. Import backup configuration 4. Restart the router 5. Login to telnet with username and password = admin : db40 6. Download sysupgrade binary and mtd_write to the kernel partition `mtd_write write openwrt-bolt_bl100-squashfs-sysupgrade.bin Kernel` Signed-off-by: Radito Wahyu <arditogits@gmail.com>
* ramips: mt7620a_tplink_archer-c5-v4: use LED_FUNCTION_WLAN_2GHZ and ↵Mieczyslaw Nalewaj2024-03-29
| | | | | | | | LED_FUNCTION_WLAN_5GHZ Use LED_FUNCTION_WLAN_2GHZ and LED_FUNCTION_WLAN_5GHZ instead function-enumerator Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: add support for TP-Link RE205 v3Steffen Loley2024-03-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE205 v3 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with external antennas. It's based on MediaTek MT7628AN+MT7610EN like the RE200 v3/v4 but with external antennas. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 5x LED (GPIO-controlled), 2x button - UART connection holes on PCB (57600 8n1) There are 2.4G and 5G LEDs in blue which are controlled separately. Installation ------------ Installation is identical to RE200 v3 devices as described at https://openwrt.org/toh/tp-link/re200#installation Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- U-Boot seems to be locked on newer versions, if not it can be accessed over the UART as described in the link above. Signed-off-by: Steffen Loley <slo-src@web.de>
* ramips: add support for Z-ROUTER ZR-2660Mikhail Zhilkin2024-03-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich AX1800) wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7621AT, MIPS, 880 MHz - RAM : 256 MiB - Flash : NAND 128 MiB (AMD/Spansion S34ML01G2) - WLAN : - 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2 - 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN) - USB : 1x 2.0 - UART : 3.3V, 115200n8, pins are silkscreened on the pcb - Buttons : 1x Reset - LEDs : 1x WiFi 2.4 GHz (green) 1x WiFi 5 GHz (green) 1x LAN (green) 1x WAN (green) 1x WAN no-internet (red) - Power : 12 VDC, 1 A Installation ------------ 1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs image (initramfs.bin) to the tftp root dir 2. Open the following link in the browser to enable telnet: http://192.168.2.1/cgi-bin/telnet_ssh 3. Connect to the router (default IP: 192.168.2.1) using telnet shell (credentials - user:admin) 4. Run the following commands in the telnet shell (this will install OpenWrt initramfs image on nand flash): cd /tmp tftp -g -r initramfs.bin 192.168.2.2 mtd write initramfs.bin firmware mtd erase firmware_backup reboot 5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the router 6. Connect to the router (IP: 192.168.1.1) using ssh shell and run sysupgrade command: sysupgrade -n /tmp/sysupgrade.bin Return to stock --------------- 1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp 2. Run following command in the router shell: cd /tmp mtd write stock.bin firmware reboot Recovery -------- Connect uart (pins are silkscreened on the pcb), interrupt boot process by pressing any key, use u-boot menu to flash stock firmware image or OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | LAN | 24:0f:5e:xx:xx:4c | label | | WAN | 24:0f:5e:xx:xx:4d | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 | +---------+-------------------+-----------+ The WLAN 2.4 MAC was found in 'factory', 0x4 The LAN MAC was found in 'factory', 0xfff4 The WAN MAC was found in 'factory', 0xfffa Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for YunCore G720Daniel Golle2024-03-12
| | | | | | | | | | | | | | | | | | | | The YunCore G720 is a dual band 802.11ax router with 5 GbE ports. Specs: - SoC: MediaTek MT7621 - Ethernet: 5x GbE ports (built-in MT7530) - Wireless 2.4GHz / 5GHz: MediaTek MT7915E - RAM: 256MiB - ROM: 16MiB (W25Q128) - 1 Button (reset) - 8 LEDs (1x system, 2x wifi, 5x switch ports) Flash instructions: The vendor firmware is based on OpenWrt, the sysupgrade image can be flashed using the '-F' (force) option on the CLI. Make sure not to keep settings when doing so. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: improve support for STORYLiNK SAP-G3200U3Sungbo Eo2024-03-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | * Increase flash SPI frequency to 50MHz The maximum SPI frequency of MX25L6406EM2I is 86 MHz, but in this patch 50 MHz was chosen as a safe value. * Update Ethernet MAC addresses Till now LAN/WAN MAC addresses were flipped compared to stock firmware. * Fix Wi-Fi LEDs by adding mt76 led nodes * Fix LAN port order LAN ports are in reverse order of switch ports. * Fix the well-known "LZMA ERROR 1" error by using lzma-loader * Set uImage name, which enables installation via stock web interface: 1. Upload **initramfs** image file to the web page. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: rename mtd partition of ipTIME NAND devicesSungbo Eo2024-03-10
| | | | | | | | | | | | Contrary to common ipTIME NOR devices, the "Config" partition of T5004 and AX2004M contain normal U-Boot environment variables. Renaming the partition into "u-boot-env" serves for better description, and it also conforms to common naming practice in OpenWrt. This patch might also be extended to A3004T, but its u-boot-env partition layout has not been confirmed yet. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add NMBM support for ipTIME AX2004MSungbo Eo2024-03-10
| | | | | | | | | | | | | | | | AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the device support [1] had been added before NMBM feature in mtk_bmt driver [2]. Let's enable it now. With this change, there is a low possibility of boot failure after sysupgrade from older versions. As AX2004M already has gone through two stable releases in the meantime, it would be safe to warn users by bumping DEVICE_COMPAT_VERSION. [1] 37753f34ac68 ("ramips: add support for ipTIME AX2004M") [2] 06382d1af7b2 ("kernel: add support for mediatek NMBM flash mapping support") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: Unielec u7621-01: remove invalid led statusDavid Bentham2024-03-02
| | | | | | | | | | The original commit had an invalid setting of the led status for this device. There is no gpio pin connected to that led so lets remove these from the u7621-01 dtsi file. Signed-off-by: David Bentham <db260179@gmail.com>
* ramips: fix nvmem-cells for routers based on TP-Link ArcherMieczyslaw Nalewaj2024-02-29
| | | | | | Added missing nvmem-cells located in the loaded file mt7620a_tplink_archer.dtsi Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: removing unnecessary compatibility for TP-Link Archer C2 v1Mieczyslaw Nalewaj2024-02-27
| | | | | | | Removing: compatible = "rtl8367b" This string is not used anywhere in the code. Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: TP-Link Archer C5 v4: license and file formatting fixesMieczyslaw Nalewaj2024-02-24
| | | | | | | | mt7620a_tplink_archer-c5-v4.dts - added missing SPDX-License-Identifier mt7620.mk: added missing tabulator Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: add support for TP-Link Archer C5 v4Mieczyslaw Nalewaj2024-02-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C5 v4 is a dual band router with 5 GbE ports Advertised as AC1200 for its 867Mbps (2x2) 5GHz band and 300 Mbps (2x2) 2.4GHz band. Specs: - SoC: MediaTek MT7620A - Ethernet: 5x GbE ports (Realtek RTL8367S) - Wireless 2.4GHz: MediaTek MT7620A - Wireless 5GHz: MediaTek MT7612E - RAM: 64MiB - ROM: 8MiB (GD25Q64CSIG) - 1 USB 2.0 port - 2 Buttons (WPS and reset) - 8 LEDs Flash instructions: Currently one has to install OpenWrt only via the serial console 1. Rename the factory.bin to to test.bin 2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin 3. connect your device to the LAN port 4. power up the router and press 4 on the console to stop the boot process. 5. enter the following commands on the router console tftp 0x80060000 test.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [Update leds, add fast-read] Signed-off-by: Gaspare Bruno <gaspare@anlix.io> [Rebuilt version based on mt7620 tplink_archer.dtsi, support for external LNA, remove bad cell count info] Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: fix TP-Link Archer MAC address for ethernetMieczyslaw Nalewaj2024-02-24
| | | | | | | This fixes: [ 0.981884] OF: /ethernet@10100000: #nvmem-cell-cells = 1 found 0 Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
* ramips: fix and clean up D-Link MAC addressAlan Luck2024-02-22
| | | | | | | | | | | | | | | | | add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi Change MAC address pointer from factory_e006 to factory_e000 + 3 same as used in D-link firmware 1.11 DIR-1960-A1 DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1 Clean-up MAC addresses in D-Link NOR devices DTS's Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ? as later devices don't have the MAC address in factory configuration same as used in D-Link firmware 1.30 DIR-878-A1 DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1 * D-link software differs between source of wan address Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
* ramips: clean up useless dts partition labelsShiji Yang2024-02-21
| | | | | | | | | | The previous NVMEM eeprom conversions[1][2] left a lot of partition labels that were no longer used. They can be removed now. [1] https://github.com/openwrt/openwrt/pull/13584 [2] https://github.com/openwrt/openwrt/pull/13587 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix dts error in LED color/function conversionChristian Marangi2024-02-08
| | | | | | | | Fix DTS error in LED color/function conversion due to a bug in the conversion script. Fixes: 19c45b95dbb5 ("ramips: convert to new LED color/function format where possible") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: convert to new LED color/function format where possibleChristian Marangi2024-02-07
| | | | | | | | Initial conversion to new LED color/function format and drop label format where possible. The same label is composed at runtime. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: drop redundant label with new LED color/function formatChristian Marangi2024-02-07
| | | | | | | | | Drop redundant label with new LED color/function format declared. This was needed previously when the new format wasn't supported by leds.sh functions script. Now that is supported this property can be removed in favor of the new format. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: mt7621: convert Linksys devices EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | | | | | -+-----------------------------+- | Model | NIC | -+-----------------------------+- | EA6350 v4 | MT7603 + MT7613 | -+-----------------------------+- | EA7300 v2 | MT7603 + MT7615 | -+-----------------------------+- | Others | MT7615 *2 | -+-----------------------------+- Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621: convert NETGEAR devices EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | | | -+------------------------------+- | Model | NIC | -+------------------------------+- | chj series | MT7603 + MT7615 | -+------------------------------+- | bzv series | MT7615 *2 | -+------------------------------+- Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621: convert Wavlink devices EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | | | -+------------------------------+- | Model | NIC | -+------------------------------+- | WL-WN531A6 | MT7603 + MT7615 | -+------------------------------+- | WL-WN533A8 | MT7615 *2 | -+------------------------------+- Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621: convert Ubiquiti devices EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | -+-------------------------+- | Model | NIC | -+-------------------------+- | All | MT7603 + MT7615 | -+-------------------------+- Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621: convert I-O DATA devices EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | | | -+-------------------------------------------+- | Model | NIC | -+-------------------------------------------+- | WN-DX1167R/WN-AX1167GR2 | MT7615D | -+-------------------------------------------+- | WN-AX2033GR/WN-DX2033GR | MT7603 + MT7615 | -+-------------------------------------------+- Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621: convert Xiaomi devices EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | | | | | -+---------------------------+- | Model | NIC | -+---------------------------+- | AC2100 | MT7603 + MT7615 | -+---------------------------+- | MI4A V2 | MT7603 + MT7613 | -+---------------------------+- | Others | MT7603 + MT7612 | -+---------------------------+- Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621: convert MT7915 EEPROM to NVMEM formatShiji Yang2024-01-17
| | | | | | | | | | | | | Some MT7915 calibration data consists of two parts. The first part "eeprom" size is 0xe00. The second part "precal" size is 0x19c10. Though some devices may not have precal data, it's better to assume that precal data exists as no users/developers confirm it. On the other hand, some devices definitely do not contain precal data because the EEPROM partition size is smaller than the precal NVMEM cell size. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt76x8: add support for TP-Link RE365 v1Tomasz Maciej Nowak2024-01-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE365 is a wireless range extender, hardware-wise resembles RE305 with slight changes regarding buttons and LEDs. Specification SoC: MediaTek MT7628AN RAM: 64 MiB DDR2 Flash: 8 MiB SPI NOR WiFi: 2.4 GHz 2T2R integrated 5 GHz 2T2R MediaTek MT7612EN conncted to PCIe lanes Ethernet: 1x 10/100 Mbps integrated LEDs: 6x GPIO controlled Buttons: 4x GPIO controlled UART: row of 4 holes marked on PCB as J1, starting count from white triangle 1. VCC (3.3V), 2. GND, 3. RX, 4. TX baud: 57600, parity: none, flow control: none Installation 1. Open web management interface. 2. Go to Settings > System Tools > Firmware upgrade. 3. Select "Browse" and select the OpenWrt image with factory.bin suffix. 4. After selecting "Upgrade" firmware writing process will start. 5. Wait till device reboots, power LED should stay solid when it's fully booted, then it's ready for configuration through LAN port. Additional information With how device manufacturer patrtitioned the flash memory, it's possible that with default packages set, initial factory.bin image won't be created. In such case, try to reduce packages amount or use older release for initial conversion to OpenWrt. Later You can use sysupgrade.bin image with full set of packages because OpenWrt uses unpartitioned flash memory space unused by vendor firmware. Reverting to vendor firmware involves converting firmware using tplink-safeloader with -z option (can be found in ImageBuilder or SDK) and forcibly applying converted firmware as sysupgrade. Known issues WARNING: after removing casing of the device one is exposed to high voltage and is in a risk of being electrocuted. Caution when interfacing whith bootloader, saving its environment either by issuing "saveenv" or selecting option "1: Load system code to SDRAM via TFTP." in boot menu, any of those will lead to overwriting part of kernel. This will lead to need of firmware recovery. The cause of this issue is bootloader having environment offset on flash at 0x40000, while kernel starts from 0x20000. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [Wrap long line in DTS] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ramips: sercomm s1500: enable wlan LEDs activity blinkingMikhail Zhilkin2024-01-07
| | | | | | | | | This commit enables wireless LEDs activity blinking for Sercomm S1500 devices (Beeline Smartbox PRO, WiFire s1500.nbn). Run-tested: WiFire s1500.nbn Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: update leds & buttons dts descriptionMikhail Zhilkin2024-01-07
| | | | | | | | | | | | | This commit: 1. Removes deprecated "label" property from the dts leds subnnodes; 2. Updates buttons and leds dts description according to kernel docs examples. Scope: devices well known to me. Run-tested: TP-Link ec330-g5u, WiFire S1500.nbn Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add missing syscon compatible strings for MT7688 and RT3052Shiji Yang2024-01-06
| | | | | | | | | | | | MT7688 devices use the "mt7628an.dtsi" as the template. And RT3052 devices use the "rt3050.dtsi" as template. Therefore, we need to add the corresponding system controller compatible strings to make them work properly. Fixes: 1f818b09f8ae ("ramips: add proper system clock and reset driver support for legacy SoCs") Fixes: #14305 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: reset mt7620 ethernet phy via reset controllerShiji Yang2024-01-06
| | | | | | | | | | | Use reset controller to reset mt7620 ethernet phy instead of directly writing system control registers. The reset line of "ephy" is 24, so the DTS resets properties have been updated to get the correct reset signal. Tested on HiWiFi HC5861. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix dtc warningsRosen Penev2024-01-05
| | | | | | Mostly leading 0 removals and wrong addresses. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: unielec-u7621-01: Increase SPI frequency to 50MHzDavid Bentham2024-01-03
| | | | | | | | | | | | Flash: 16MB SPI NOR flash (Macronix MX25L12805D) Based on the manufactured datasheet this chip is capable of 50MHz. We dont enable fast-read as mt7621 are only capable of 44mhz in a read state. Tested on this unit without any issues. Signed-off-by: David Bentham <db260179@gmail.com>
* ramips: dts: mt7628an: reset FE and ESW cores togetherMaxim Anisimov2024-01-02
| | | | | | | | | | | | | Failing to do so will cause the DMA engine to not initialize properly and fail to forward packets between them, and in some cases will cause spurious transmission with size exceeding allowed packet size, causing a kernel panic. Fixes: 60fadae62b64 ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe") Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com> [Provide commit description, split into logical changes] Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: dts: rt5350: reset FE and ESW cores togetherLech Perczak2024-01-02
| | | | | | | | | | | | | | | | Failing to do so will cause the DMA engine to not initialize properly and fail to forward packets between them, and in some cases will cause spurious transmission with size exceeding allowed packet size, causing a kernel panic. This is behaviour of downstream driver as well, however I haven't observed bug reports about this SoC in the wild, so this commit's purpose is to align this chip with all other SoC's - MT7620 were already using this arrangement. Fixes: #9284 Fixes: 60fadae62b64 ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: dts: rt3050: reset FE and ESW cores togetherLech Perczak2024-01-02
| | | | | | | | | | | | | | | Failing to do so will cause the DMA engine to not initialize properly and fail to forward packets between them, and in some cases will cause spurious transmission with size exceeding allowed packet size, causing a kernel panic. This is behaviour of downstream driver as well, however I haven't observed bug reports about this SoC in the wild, so this commit's purpose is to align this chip with all other SoC's - MT7620 were already using this arrangement. Fixes: 60fadae62b64 ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: dts: rt3352: reset FE and ESW cores togetherMaxim Anisimov2024-01-02
| | | | | | | | | | | | | Failing to do so will cause the DMA engine to not initialize properly and fail to forward packets between them, and in some cases will cause spurious transmission with size exceeding allowed packet size, causing a kernel panic. Fixes: 60fadae62b64 ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe") Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com> [Provide commit description, split into logical changes] Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: fix label-mac for Xiaomi RA75David Bauer2023-12-28
| | | | | | | The label-mac of the repeater is the address used on the 2.4 GHz radio, not the ethernet MAC. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: correct the PCIe port number for Unielec u7621-01David Bentham2023-12-25
| | | | | | | | | | | | | | | | | MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe port will cause the PCIe NIC to not work properly. This commit fixes the wrong port numbers on Unielec u7621-01. According to the bootlog, MT7612E (5 GHz) is connected to pcie2, and MT7603E (2 GHz) is connected to pcie1: [ 1.294844] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK) [ 1.308635] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.318277] mt7621-pci 1e140000.pcie: PCIE2 enabled Also correct the led activity for the MT7603e - not used on the MT7612e Signed-off-by: David Bentham <db260179@gmail.com>
* ramips: remove systick node for mt7621 SoC dtsiShiji Yang2023-12-25
| | | | | | | This node is useless because MT7621 uses the generic mips systick driver instead of the ralink systick driver. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: remove useless resets properties from SoC dtsiShiji Yang2023-12-25
| | | | | | | | | | | | | | | These drivers don't request reset control. And most reset properties even have incorrect reset source definitions. 1. interrupt controller, ref: arch/mips/ralink/irq.c 2. memory controller, ref: arch/mips/ralink/of.c 3. gpio controller, ref: drivers/gpio/gpio-ralink.c (local patch) 4. systic, ref: arch/mips/ralink/cevt-rt3352.c 5. pwm, ref: drivers/pwm/pwm-mediatek-ramips.c (local patch) Tested on MT7620 && MT7628. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add TP-LINK TL-WR902AC v4Kamil Jońca2023-12-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Seems to be very similar to: https://openwrt.org/toh/tp-link/tl-wr902ac_v3 1 x usb 1 x eth Powered by mini usb port. Installation: Can use TFTP method to install: 1. establish TFTP server at 192.168.0.66 2. provide tp_recover.bin file to the TFTP server 3. turn on router with reset button pressed 4. wait for led blinking, then release reset Specification based on dmesg from already flashed device: SoC Type: MediaTek MT7628AN ver:1 eco:2 CPU0 revision is: 00019655 (MIPS 24KEc) Memory: 56028K/65536K available CPU Clock: 580MHz WiFi: MT7613BE MAC addresses are all the same, except wifi5g which last part is decrement by one, ie.: eth0 40:ed:00:cf:b9:9b br-lan 40:ed:00:cf:b9:9b phy0-ap0 40:ed:00:cf:b9:9b phy1-ap0 40:ed:00:cf:b9:9a Signed-off-by: Kamil Jońca <kjonca@onet.pl>
Powered by cgit, Themed by Ted Yin.