aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ramips/dts/mt7621_bolt_arion.dts
Commit message (Collapse)AuthorAge
* ramips: clean up useless dts partition labelsShiji Yang2024-02-21
| | | | | | | | | | The previous NVMEM eeprom conversions[1][2] left a lot of partition labels that were no longer used. They can be removed now. [1] https://github.com/openwrt/openwrt/pull/13584 [2] https://github.com/openwrt/openwrt/pull/13587 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert to new LED color/function format where possibleChristian Marangi2024-02-07
| | | | | | | | Initial conversion to new LED color/function format and drop label format where possible. The same label is composed at runtime. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: mt7621: nix mac-address-incrementRosen Penev2023-11-26
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: convert MT7610 and MT7612 EEPROM to NVMEM format for MT7621Shiji Yang2023-10-09
| | | | | | | This patch converts MT7610 and MT7612 WiFi calibration data to NVMEM format. The EEPROM size is 0x200. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert MT7603 EEPROM to NVMEM formatShiji Yang2023-10-09
| | | | | | | This patch converts MT7603 WiFi calibration data to NVMEM format. The EEPROM size is 0x400. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: correct NVMEM MAC address node name and label for Bolt ArionShiji Yang2023-10-09
| | | | | | | The node name&label should match the address in the 'reg' property, so it's better to change the incorrect offset to the 0x28. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7621-dts: do not claim rgmii2 group as gpio for certain devicesArınç ÜNAL2022-08-20
| | | | | | | | | | | | | | | These devices do not use rgmii2 as gpio, therefore remove rgmii2 pin group from state-default. Remove overwriting the ethernet node for these devices. Move claiming the rgmii2 group from mt7621_zyxel_nwa-ax.dtsi to mt7621_zyxel_nwa50ax.dts as it's only the latter using rgmii2 pins as gpio. Remove duplicate ethernet overwrite from mt7621_tplink_archer-x6-v3.dtsi. Claim rgmii2 group as gpio on mt7621_bolt_arion.dts as it uses an rgmii2 pin, 26, as gpio. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-16
This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
Powered by cgit, Themed by Ted Yin.