aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ramips/dts/mt7621_asus_rp-ac56.dts
Commit message (Collapse)AuthorAge
* ramips: clean up useless dts partition labelsShiji Yang2024-02-21
| | | | | | | | | | The previous NVMEM eeprom conversions[1][2] left a lot of partition labels that were no longer used. They can be removed now. [1] https://github.com/openwrt/openwrt/pull/13584 [2] https://github.com/openwrt/openwrt/pull/13587 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert to new LED color/function format where possibleChristian Marangi2024-02-07
| | | | | | | | Initial conversion to new LED color/function format and drop label format where possible. The same label is composed at runtime. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: mt7621: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: convert MT7610 and MT7612 EEPROM to NVMEM format for MT7621Shiji Yang2023-10-09
| | | | | | | This patch converts MT7610 and MT7612 WiFi calibration data to NVMEM format. The EEPROM size is 0x200. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert MT7603 EEPROM to NVMEM formatShiji Yang2023-10-09
| | | | | | | This patch converts MT7603 WiFi calibration data to NVMEM format. The EEPROM size is 0x400. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix dts whitespaceFelix Baumann2023-02-09
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: adding support for Asus RP-AC56Lea Teuberth2022-08-06
Specifications: CPU: MT7621A dual-core 880MHz RAM: 64MB DDR2 FLASH: 16MB MX25L12805D NOR SPI WIFI: 2.4GHz 2x2 MT7603 b/g/n PCI WIFI: 5GHz 2x2 MT7662 a/b/ac PCI ETH: 1xLAN 1000base-T integrated SWITCH: MT7530 Port 0: LAN, Port 6: CPU LED: Power, 2.4GHz WiFi, 5GHz WiFi BTN: WPS, Reset UART: Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1 MISC: Audio support Installation: 1. Update using recovery mode - while holdig "reset" button, power on the device - keep holding "reset" until power led is flashing yellow - set own IP to 192.168.1.75, subnet mask: 255.255.255.0 - push firmware image (can be factory.bin or sysupgrade.bin) using tftp client in binary mode to 192.168.1.1 Notes: This board has only two MAC addresses programmed in the "factory" partition: - MAC for wlan0 (2.4GHz) at offset 0x0004 - MAC for wlan1 (5GHz) at offset 0x8004 - stock firmware re-uses wlan0 MAC for ethernet - no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006 Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
Powered by cgit, Themed by Ted Yin.