aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ramips/mt7621/config-5.10
Commit message (Collapse)AuthorAge
* treewide: remove files for building 5.10 kernelNick Hainke2023-05-12
| | | | | | | | | | | All targets are bumped to 5.15. Remove the old 5.10 patches, configs and files using: find target/linux -iname '*-5.10' -exec rm -r {} \; Further, remove the 5.10 include. Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic configAleksander Jan Bajkowski2022-10-21
| | | | | | | | | | | | | | | | | | | | | | | | | Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should be enabled on target or subtarget based on SoC architecture. Fixes warning: $ make kernel_oldconfig CONFIG_TARGET=subtarget ... .config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state .... Summary: - ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture. If it is disabled then the processor operates in LITTLE_ENDIAN mode (default), - ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This option should be enabled after OpenWRT moves to kernel 6.x. After refreshing the kernel, the symbol disappears, - ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN, - MIPS - enabled relevant symbols, - POWERPC - enabled CONFIG_CPU_BIG_ENDIAN, - UML - Symbols are not defined for this architecture, - X86 - always little endian. Symbols are not defined for this architecture. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-19
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: move ubnt ledbar driver to a separate packageFelix Fietkau2022-09-30
| | | | | | | Simplifies the tree by removing a non-upstream kernel patch and related kconfig symbols Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for Ubiquiti UniFi FlexHDSven Wegener2022-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- - SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash - Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4) - Bluetooth: CSR8811 (internal USB, install kmod-bluetooth) Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-20
| | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* kernel: Activate CONFIG_GPIOLIB in generic configurationHauke Mehrtens2022-08-10
| | | | | | | | All targets expect the malta target already activate the CONFIG_GPIOLIB option. Move it to generic kernel configuration and also activate it for malta. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "nftables: fix parsing date expressions"Jo-Philipp Wich2022-08-09
| | | | | | | | This reverts commit eada8925776aafa3ec47d66fb89bf7eae730edf7. The commit contained unrelated target changes. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* nftables: fix parsing date expressionsJo-Philipp Wich2022-08-09
| | | | | | | | Musl libc does not support the non-POSIX "%F" format for strptime() so replace all occurrences of it with an equivalent "%Y-%m-%d" format. Fixes: #10419 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add support for Beeline SmartBox GIGAMikhail Zhilkin2022-07-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-24
| | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-09
| | | | | | | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and MT7531. Fix some link up/down issues. The errornous check for the PHY mode which broke things with MT7531 has been removed as suggested by patch net: phy: mediatek: remove PHY mode check on MT7531 As a result, things are working fine now on MT7622+MT7531 as well. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* Revert "kernel: backport MediaTek Ethernet PHY driver"Hauke Mehrtens2022-02-05
| | | | | | | | | | | | | | | | | | This reverts commit 8b4cba53a9402f44da2dced4a78ca065b15dca94. This broke the mt7530 on Linksys e8450 (mt7622) for me. [ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL [ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0 [ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL [ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1 [ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL [ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2 [ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL [ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3 [ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL [ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport MediaTek Ethernet PHY driverDENG Qingfang2022-02-05
| | | | | | | | | Add support for MediaTek Gigabit Ethernet PHYs found in MT7530. Fix some link up/down issues. Signed-off-by: DENG Qingfang <dqfext@gmail.com> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: enable I2C_CHARDEV in mt7621/config-5.10Stijn Tintel2022-01-28
| | | | | | | | I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the 5.10 config, as it's required for PoE control on Unifi Switch Flex. Fixes: b4aad29a1d7a ("ramips: add support for kernel 5.10") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: enable badblock table support on linksys ea7xxx devicesFelix Fietkau2022-01-13
| | | | | | Use remapping only on the kernel partitions. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mikrotik: enable variable size eraseOskari Lemmela2022-01-13
| | | | | | | Add support for variable size erase blocks. Enable it to all targets which has mikrotik targets. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* kernel: 5.10: consolidate mac80211 crypto optionsSergey Ryazanov2021-12-17
| | | | | | | | | | | | | | | | | | | | | | Each of - CRYPTO_AEAD2 - CRYPTO_AEAD - CRYPTO_GF128MUL - CRYPTO_GHASH - CRYPTO_HASH2 - CRYPTO_HASH - CRYPTO_MANAGER2 - CRYPTO_MANAGER - CRYPTO_NULL2 either directly required for mac80211 crypto support, or directly selected by such options. Support for the mac80211 crypto was enabled in the generic config since c7182123b9 ("kernel: make cryptoapi support needed by mac80211 built-in"). So move the above options from the target configs to the generic config to make it clear why do we need them. CC: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: filter out both Clang and LLD versionsSergey Ryazanov2021-12-17
| | | | | | | | Both CLANG_VERSION and LLD_VERISON are autogenerated runtime configuration options, so add them to the kernel configuration filter and remove from generic and per-target configs to keep configs clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: move two symbols to the generic kconfigsRui Salvaterra2021-08-29
| | | | | | | CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them to the generic kconfigs. And resort the generic kconfigs while at it. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: fix missing NVMEM subsystemDavid Bauer2021-07-21
| | | | | | | | | | | | MAC address retrieval was switched to more generic upstream (5.13) NVMEM based solution in commit 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") , but NVMEM subsystem wasn't enabled in the kernel, so fix it now. References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801 Fixes: 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation") Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
* ramips: add support for Tenbay T-MB5EU-V01David Bauer2021-06-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7621 SoC 256M DDR3 16MB BoHong SPI-NOR MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax RGB LED WPS + RESET Button UART on compute module (silkscreened / 115200n8) The router itself is just a board with Power / USB / RJ-45 connectors and DC/DC converters. The SoC and WiFi components are on a daughterboard which connect using two M.2 connectors. The compute module has the model number "T-CB1800K-DM2 V02" printed on it. The main baord has "T-MB5EU V01" printed on it. This information might be useful, as it's highly likely either of these two will be reused in similar designs. The router itself is sold as Tenbay T-MB5EU directly from the OEM as well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a slightly different case. Installation ------------ A Tool for creating a factory image for the Vendor Web Interface can be found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/ As the OEM Firmware is just a modified LEDE 17.01, you can also access failsafe mode via UART while the OS boots, by connecting to UART and pressing "f" when prompted. The Router is reachable at 192.168.1.1 via root without password. Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade using the -n and -F flags. Alternatively, the board can be flashed by attaching to the UART console, interrupting the boot process by keeping "0" pressed while attaching power. Serve the OpenWrt initramfs using a TFTP server with address 192.168.1.66. Rename the initramfs to ax1800.bin. Attach your TFTP server to one of the LAN ports. Execute the following commands. $ setenv ipaddr 192.168.1.67 $ setenv serverip 192.168.1.66 $ tftpboot 0x84000000 ax1800.bin $ bootm Wait for the device to boot. Then transfer the OpenWrt sysupgrade image to the device using SCP and apply sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add AW9523 I2C GPIO expander driverDavid Bauer2021-06-27
| | | | | | | | | | | | | | This adds a driver for the AW9523 I2C GPIO expander. This driver is required to make LEDs as well as buttons on the Tenbay T-MB5EU-V01 work. This driver already had several upstream iterations. I'm working to push this driver to mainline. Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287 Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-21
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove redundant ubifs kconfig symbolsRui Salvaterra2021-04-21
| | | | | | | For the targets which enable ubifs, these symbols are already part of the generic kconfigs. Drop them from the target kconfigs. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: enable support for cpuidleRui Salvaterra2021-03-31
| | | | | | | | | | | MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support deep sleep idle states and have a specific cpuidle driver for them. Enable support for it, while also switching from constant timer ticks to the idle dynticks model, with the TEO governor. Run-tested on a Redmi AC2100. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: 5.10: refresh configsIlya Lipnitskiy2021-03-06
| | | | | | | | Run-tested on Ubiquiti EdgeRouter X. Compile tested on all other subtargets. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: copy config-5.4 to config-5.10Ilya Lipnitskiy2021-03-06
| | | | | | Strict copy, no changes made. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* Revert "ramips: add support for kernel 5.10"Adrian Schmutzler2021-03-06
| | | | | | | | | This reverts commit b4aad29a1d7ad77d67073c1c54b28c429c64ed9b. This was accidentally folded into a single commit. Remove it and apply it properly again. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for kernel 5.10Ilya Lipnitskiy2021-03-05
Enable testing kernel. Delete upstreamed patches: 0098-disable_cm.patch can be dropped, upstream fixed CM handling. Fix compile errors by using new kernel APIs. Fix fuzz by manually editing patches to ensure the code goes in the right place. For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit a307593a6 to keep the OpenWrt ralink driver operational. Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693 and #3952. Rename patches to follow the 3-digit classification from the OpenWrt Developer Guide. Run automatic quilt refresh. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Powered by cgit, Themed by Ted Yin.