aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ramips/mt7621/base-files
Commit message (Collapse)AuthorAge
* ramips: Add support for D-Link DIR-3040 A1Vince McKinsey2024-04-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the A1 hardware revision of the DIR-3040. It is an exact copy of the DIR-3060 save for some cosmetic changes to the housing. Even going so far as having the same FCC ID. Hardware specification: SoC: MediaTek MT7621AT Flash: Winbond W29N01HVSINA 128MB RAM: Micron MT41K128M16JT-125 256MB Ethernet: 5x 10/100/1000 Mbps WiFi1: MT7615DN 2.4GHz N 2x2:2 WiFi2: MT7615DN 5GHz AC 2x2:2 WiFi3: MT7615N 5GHz AC 4x4:4 Button: WPS, Reset Flash instructions: OpenWrt can be installed via D-Link Recovery GUI: NOTE: Seems to only work in Firefox on Windows. Tried with Chrome on Windows, Firefox in Linux, and Chromium in Linux. None of these other browsers worked. 1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable. 2. Give it ~30 seconds, to boot the recovery mode GUI 3. Connect your client computer to LAN1 of the device 4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0. 5. Call the recovery page for the device at http://192.168.0.1/ 6. Use the provided emergency web GUI to upload and flash a new firmware to the device Thanks to @Lucky1openwrt and @iivailo for creating the DIR-3060 DTS file and related changes, so it was possible for me to adapt them to the DIR-3040, build images, test and fix minor issues. MAC Addresses: | use | address | example | | --- | --- | --- | | LAN | label | f4:*:61 | | WAN | label + 4 | f4:*:65 | | WI1/2g | label + 2 | f4:*:63 | | WI1/5g | label + 1 | f4:*:62 | | WI2/5g | label + 3 | f4:*:64 | The label MAC address was found in Factory, 0xe000 Checklist: ✓ nand ✓ ethernet ✓ button ✓ wifi2g ✓ wifi5g ✓ wifi5g ✓ mac ✓ led Signed-off-by: Vince McKinsey <vincemckinsey@gmail.com>
* ramips: add support for Z-ROUTER ZR-2660Mikhail Zhilkin2024-03-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich AX1800) wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7621AT, MIPS, 880 MHz - RAM : 256 MiB - Flash : NAND 128 MiB (AMD/Spansion S34ML01G2) - WLAN : - 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2 - 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN) - USB : 1x 2.0 - UART : 3.3V, 115200n8, pins are silkscreened on the pcb - Buttons : 1x Reset - LEDs : 1x WiFi 2.4 GHz (green) 1x WiFi 5 GHz (green) 1x LAN (green) 1x WAN (green) 1x WAN no-internet (red) - Power : 12 VDC, 1 A Installation ------------ 1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs image (initramfs.bin) to the tftp root dir 2. Open the following link in the browser to enable telnet: http://192.168.2.1/cgi-bin/telnet_ssh 3. Connect to the router (default IP: 192.168.2.1) using telnet shell (credentials - user:admin) 4. Run the following commands in the telnet shell (this will install OpenWrt initramfs image on nand flash): cd /tmp tftp -g -r initramfs.bin 192.168.2.2 mtd write initramfs.bin firmware mtd erase firmware_backup reboot 5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the router 6. Connect to the router (IP: 192.168.1.1) using ssh shell and run sysupgrade command: sysupgrade -n /tmp/sysupgrade.bin Return to stock --------------- 1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp 2. Run following command in the router shell: cd /tmp mtd write stock.bin firmware reboot Recovery -------- Connect uart (pins are silkscreened on the pcb), interrupt boot process by pressing any key, use u-boot menu to flash stock firmware image or OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | LAN | 24:0f:5e:xx:xx:4c | label | | WAN | 24:0f:5e:xx:xx:4d | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 | +---------+-------------------+-----------+ The WLAN 2.4 MAC was found in 'factory', 0x4 The LAN MAC was found in 'factory', 0xfff4 The WAN MAC was found in 'factory', 0xfffa Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for YunCore G720Daniel Golle2024-03-12
| | | | | | | | | | | | | | | | | | | | The YunCore G720 is a dual band 802.11ax router with 5 GbE ports. Specs: - SoC: MediaTek MT7621 - Ethernet: 5x GbE ports (built-in MT7530) - Wireless 2.4GHz / 5GHz: MediaTek MT7915E - RAM: 256MiB - ROM: 16MiB (W25Q128) - 1 Button (reset) - 8 LEDs (1x system, 2x wifi, 5x switch ports) Flash instructions: The vendor firmware is based on OpenWrt, the sysupgrade image can be flashed using the '-F' (force) option on the CLI. Make sure not to keep settings when doing so. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add factory image for ipTIME AX2004MSungbo Eo2024-03-10
| | | | | | | | | | | | | Unlike the recovery image, this initramfs-factory image can be flashed using the stock firmware web interface (from any active boot partition), as well as the bootloader recovery web page. Drop the recovery image in favor of the factory image. Installation via stock/recovery web interface: 1. Flash **initramfs-factory** image through the web page. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: rename mtd partition of ipTIME NAND devicesSungbo Eo2024-03-10
| | | | | | | | | | | | Contrary to common ipTIME NOR devices, the "Config" partition of T5004 and AX2004M contain normal U-Boot environment variables. Renaming the partition into "u-boot-env" serves for better description, and it also conforms to common naming practice in OpenWrt. This patch might also be extended to A3004T, but its u-boot-env partition layout has not been confirmed yet. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add NMBM support for ipTIME AX2004MSungbo Eo2024-03-10
| | | | | | | | | | | | | | | | AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the device support [1] had been added before NMBM feature in mtk_bmt driver [2]. Let's enable it now. With this change, there is a low possibility of boot failure after sysupgrade from older versions. As AX2004M already has gone through two stable releases in the meantime, it would be safe to warn users by bumping DEVICE_COMPAT_VERSION. [1] 37753f34ac68 ("ramips: add support for ipTIME AX2004M") [2] 06382d1af7b2 ("kernel: add support for mediatek NMBM flash mapping support") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: update leds & buttons dts descriptionMikhail Zhilkin2024-01-07
| | | | | | | | | | | | | This commit: 1. Removes deprecated "label" property from the dts leds subnnodes; 2. Updates buttons and leds dts description according to kernel docs examples. Scope: devices well known to me. Run-tested: TP-Link ec330-g5u, WiFire S1500.nbn Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for Rostelecom RT-FE-1AMikhail Zhilkin2023-12-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: No Button: 2 buttons (Reset & WPS) LEDs: - 1x Power (green, unmanaged) - 1x Status (green, gpio) - 1x 2.4G (green, hardware, mt76-phy0) - 1x 2.4G (blue, gpio) - 1x 5G (green, hardware, mt76-phy1) - 1x 5G (blue, gpio) - 5x Ethernet (green, hardware, 4x LAN & WAN) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (default http://192.168.0.1/) under "admin" account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following block: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" /> </OBJECT> 5. Replace <some value> by a new superadmin password and add a line which enabling superadmin login after. For example, the block after the changes: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" /> <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> </OBJECT> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (superadmin:xxxxxxxxxx, where xxxxxxxxxx is a new password from the p.5) 9. Enable SSH access to the router (Settings -> Access control -> SSH) 10. Connect to the router using SSH shell using superadmin account 11. Run in SSH shell: sh 12. Make a mtd backup (optional, see related section) 13. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 14. Login to the router web interface under admin account 15. Remove dots from the OpenWrt factory image filename 16. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 192.168.0.2 MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | f4:*:66 | | WAN | label + 11 | f4:*:71 | | 2g | label + 2 | f4:*:68 | | 5g | label + 3 | f4:*:69 | +-----+------------+---------+ The label MAC address was found in Factory, 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for TP-Link EX220 v1Darlan Pedro de Campos2023-11-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is very similar, if not identical, to the TP-Link AX23 v1 but is targeted at service providers and features a completely different flash layout. Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Flashing is only possible via a serial connection using the sysupgrade image; the factory image must be signed. You can flash the sysupgrade image directly through the U-Boot console, or preferably, by booting the initramfs image and flashing with the sysupgrade command. Follow these steps for sysupgrade flashing: 1. Establish a UART serial connection. 2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image there. 3. Power on the device and press any key to interrupt normal boot. 4. Load the initramfs image using tftpboot. 5. Boot with bootm. 6. If you haven't done so already, back up all stock mtd partitions. 7. Copy the sysupgrade image to the router. 8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember not to attempt saving settings. Revert to stock firmware ------------------------ Flash stock firmware via OEM web-recovery mode. If you don't have access to the stock firmware image, you will need to restore the firmware partition backed up earlier. Web-Recovery ------------ The router supports an HTTP recovery mode: 1. Turn off the router. 2. Press the reset button and power on the device. 3. When all LEDs start flashing, release reset and quickly press it again. The interface is reachable at 192.168.0.1 and supports installation of the OEM factory image. Note that flashing OpenWrt this way is not possible, as mentioned above. Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
* ramips: add support for D-Link COVR-X1860 A1Roland Reinl2023-11-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The COVR-X1860 are MT7621-based AX1800 devices (similar to DAP-X1860, but with two Ethernet ports and external power supply) that are sold in sets of two (COVR-X1862) and three (COVR-X1863). Specification: - MT7621 - MT7915 + MT7975 2x2 802.11ax (DBDC) - 256MB RAM - 128 MB flash - 3 LEDs (red, orange, white), routed to one indicator in the top of the device - 2 buttons (WPS in the back and Reset at the bottom of the device) MAC addresses: - LAN MAC (printed on the device) is stored in config2 partition as ASCII (entry factory_mac=xx:xx:xx:xx:xx:xx) - WAN MAC: LAN MAC + 3 - 2.4G MAC: LAN MAC + 1 - 5G MAC: LAN MAC + 2 The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1 Flashing via OEM Web Interface: - Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-factory.bin via the OEM web interface firmware update - The configuration wizard can be skipped by directly going to http://192.168.0.1/UpdateFirmware_Simple.html Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks red - Open a Chromium based browser and goto http://192.168.0.1 - Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.25 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks red - Open a Chromium based browser and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/openwrt/firmware-utils/blob/master/src/dlink-sge-image.c and https://raw.githubusercontent.com/openwrt/firmware-utils/master/src/dlink-sge-image.h - Compile a binary from the downloaded file, e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image - Run ./dlink-sge-image COVR-X1860 <OriginalFirmware> <OutputFile> -d - Example for firmware 102b01: ./dlink-sge-image COVR-X1860 COVR-X1860_RevA_Firmware_102b01.bin COVR-X1860_RevA_Firmware_102b01_Decrypted.bin -d The pull request is based on the discussion in https://forum.openwrt.org/t/add-support-for-d-link-covr-x1860 Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* ramips: add support for MeiG SLT866 4G CPEDaniel Golle2023-11-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: - SoC: Mediatek MT7621 (MT7621AT) - Flash: 32 MiB SPI-NOR (Macronix MX25L25635E) - RAM: 128 MiB - Ethernet: Built-in, 2 x 1GbE - 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager) - SLIC: Si32185 (unsupported) - Power: 12V via barrel connector - Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b - Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a - LEDs: 8x (7 controllable) - Buttons: 2x (RESET, WPS) Installing OpenWrt: - sysupgrade image is compatible with vendor firmware. Recovery: - Connect to any of the Ethernet ports, configure local IP: 10.10.10.3/24 (or 192.168.10.19/24, depending on OEM) - Provide firmware file named 'mt7621.img' on TFTP server. - Hold down both, RESET and WPS, then power on the board. - Watch network traffic using tcpdump or wireshark in realtime to observe progress of device requesting firmware. Once download has completed, release both buttons and wait until firmware comes up. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for ZyXEL LTE5398-M904Milan Krstic2023-10-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS port. Specifications: * SoC: Mediatek MT7621AT * RAM: 256 MB * Flash: 128MB NAND (MX30LF1G18AC) * WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G * Switch: 2 GbE ports MT7530 * LTE/3G: Quectel EG18-EA LTE-A Cat. 18 * SIM: 1 micro-SIM card slot * Buttons: Reset, WPS * LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G) * VoIP: 1 FXS RJ11 port * Power: 12V, 2A UART serial console: 57600,8N1 Unpopulated header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Installation: * Log in as root using ssh to 192.168.1.1 * scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/ * Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit * Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot * Wait for OpenWrt to boot and ssh to root@192.168.1.1 * Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image For mode details about flashing see: 2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19) Unsupported: * FXS/Voice Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
* ramips: TP-link archer A6/C6 device tree updatesRani Hod2023-10-22
| | | | | | | | | | | | | | | | Set correct GPIO (10) for the WPS button. This matches GPIO settings in vendor GPL sources. Note that GPL sources also mention a USB indicator LED (GPIO 13) but the device has neither an external USB port nor a USB LED. In addition, prefixes (button-, led-) are added to relevant DT entries, as well as color and function specifications for LEDs. Closes: #13736 Reported-by: Waldemar Czabaj <kaball@wp.pl> Signed-off-by: Rani Hod <rani.hod@gmail.com> (added led mitigations for wifi leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: fix ZyXEL NR7101 bricking typoBjørn Mork2023-10-15
| | | | | | | | | | A typo snuck in with the addition of Cudy M1800, changing "nr7101" to "nt7101". The result is a default network config for NR7101 without the only ethernet interface on the NR7101, thereby soft bricking it. Fixes: f6d394e9f2fd ("ramips: add support for Cudy M1800") Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ramips: cf-ew72-v2: Add support for COMFAST CF-EW72 V2Alexey D. Filimonov2023-09-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for COMFAST CF-EW72 V2 Hardware: - SoC: Mediatek MT7621 (MT7621DAT or MT7621AT) - Flash: 16 MiB NOR - RAM: 128 MiB - Ethernet: Built-in, 2 x 1GbE - Power: only 802.3af PD on any port, injector supplied in the box - PoE passthrough: No - Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b - Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a - LEDs: 8x (only 1 is both visible and controllable, see below) - Buttons: 1x (RESET) Installing OpenWrt: Flashing is done using Mediatek U-Boot System Recovery Mode - make wired connection with 2 cables like this: - - PC (LAN) <-> PoE Injector (LAN) - - PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet. - configure 192.168.1.(2-254)/24 static ip address on your PC LAN - press and keep pressed RESET button on device - power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable - wait for about 10 seconds until wifi led stops blinking and release RESET button - navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file - proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt) MAC addresses as verified by OEM firmware: vendor OpenWrt address LAN lan\eth0 label WAN wan label + 1 2g phy0 label + 2 5g phy1 label + 3 The label MAC address was found in 0xe000. LEDs detailed: The only both visible and controllable indicator is blue:wlan LED. It is not bound by default to indicate activity of any wireless interfaces. Place (WAN->ANT) | Num | GPIO | LED name (LuCI) | Note -----------------|-----|----------------------------------------------------------------------------------------- power | 1 | | | POWER LED. Not controlled with GPIO. hidden_led_2 | 2 | 13 | blue:hidden_led_2 | This LED does not have proper hole in shell. wan | 3 | | | WAN LED. Not controlled with GPIO. hidden_led_4 | 4 | 16 | blue:hidden_led_4 | This LED does not have proper hole in shell. lan | 5 | | | LAN LED. Not controlled with GPIO. noconn_led_6 | 6 | | | Not controlled with GPIO, possibly not connected wlan | 7 | 15 | blue:wlan | WLAN LED. Wireless indicator. noconn_led_8 | 8 | | | Not controlled with GPIO, possibly not connected mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board. Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
* ramips: fix Mercusys MR70X LAN port assignmentsAndreas Böhler2023-09-24
| | | | | | | | | A bug report in the forum found that the MR70X lists four LAN ports in LuCI while it has only three. This adds the device to the network setup file to fix the issue. Identified-by: Forum User "Lexeyko" Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add support for WAVLINK WL-WN573HX1Sijia Huang2023-09-24
| | | | | | | | | | | | | | | | | | | | Hardware -------- Specifications: - Device: WAVLINK WL-WN573HX1 Outdoor AP - SoC: MT7621AT - Flash: 16MB - RAM: 256MB - Switch:1 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x STATUS (blue, configurable) 1x LAN (green) Product link: https://www.wavlink.com/en_us/product/WL-WN573HX1.html Signed-off-by: Sijia Huang <engineer31@win-star.com>
* ramips: add support for ALFA Network AX1800RMPiotr Dymacz2023-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6 (AX1800) router, based on MediaTek MT7621A + MT79x5D platform. Specifications: - SOC: MT7621A (880 MHz) - DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK) - Flash: 16 MiB SPI NOR (EN25QH128A-104HIP) - Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch) - Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN) (MT7905DAN doesn't support background DFS scan/BT) - LED: 6x green, 1x green/red - Buttons: 2x (reset, WPS) - Antenna: 4x external, non-detachable omnidirectional - UART: 1x 4-pin (2.54 mm pitch, J4, not populated) - Power: 12 V DC/1 A (DC jack) MAC addresses: LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2) WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3) 2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label) 5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa) Flash instructions for web-based U-Boot recovery: 1. Power the device with WPS button pressed and wait around 10 seconds. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'recovery' image. The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe' mode available which allows alternative upgrade method: 1. Run device in 'failsafe' mode and change password for default user. 2. SSH to the device, transfer 'sysupgrade' image and perform upgrade in forced mode, without preserving settings: 'sysupgrade -n -F ...'. Other notes: If you own early version of this device, the vendor firmware might refuse OpenWrt image because of missing custom header. In that case, ask vendor's customer support for stock firmware without custom header support/requirement. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for D-Link DRA-1360Rani Hod2023-08-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DRA-1360 rev A is a wall-plug AC1300 repeater. Hardware is identical (same FCC ID, black case instead of white) to D-Link DAP-1620 rev B, which is already supported, but a different model name, revision, and hardware ID are needed. Thus, the bulk of the DAP-1620 device tree is extracted to a common dtsi included by the two models' device trees. Repeating specs and installation instructions from e4c7703: (note that the RAM size mentioned there was incorrect, oops) Specs: - SoC: MT7621AT (880MHz dual-core MIPS1004Kc) - Memory: 128 MiB RAM, 16 MiB NOR SPI - WiFi: MT7615DN 2x2 802.11n + 2x2 802.11ac (DBDC) - Ethernet: 1 RJ45 port 10/100/1000 - Power/status LED: red+green - LED RSSI bargraph: 2x green, 1x red+green Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 (pings are ignored, it listens only for http) - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tail -c+117 DRA1360A1_FW112B03.bin | \ openssl aes-256-cbc -d -md md5 -out decrypted.bin \ -k c471706398cb147c6619f8a04a18d53e9c17ede8 - flash decrypted.bin via D-Link Web Recovery Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ramips: add support for I-O DATA WN-DEAX1800GRINAGAKI Hiroshi2023-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB (Nanya NT5CC128M16JR-EK) - Flash : RAW NAND 128 MiB (Winbond W29N01HVSINF) - WLAN : 2.4/5 GHz (MediaTek MT7915) - Ethernet : 5x 10/100/1000 Mbps - Switch : MT7530 (SoC) - LEDs/Keys : 6x/3x - UART : through-hole on PCB (J2) - assignment: 3.3V, GND, TX, RX from "1" marking - settings : 115200n8 - Power : 12 VDC, 1 A Flash instruction using initramfs-factory image: 1. Boot WN-DEAX1800GR normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs-factory.bin image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with the squashfs-sysupgrade.bin image 5. Wait ~120 seconds to complete flashing Note: - This device has 2x OS images on the flash storage. In this support, the first one will be used. Warning: - Do not use "saveenv" command on U-Boot CLI. This device has wrong u-boot-env data. The actual length of individual env data installed to the device is 0x1000 (4 KiB), but installed U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is invalid. Then, if you perform saving environment data with saveenv on U-Boot CLI, installed env data will be overwritten with too few default values without individual values (SSID, password, MAC addresses, etc...). MAC addresses: LAN : 50:41:B9:xx:xx:F4 (Config, ethaddr (text)) WAN : 50:41:B9:xx:xx:F6 (Config, wanaddr (text)) 2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex)) 5 GHz : 50:41:B9:xx:xx:F5 (none) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: improve sysupgrade helpers for I-O DATA devicesINAGAKI Hiroshi2023-08-20
| | | | | | | | | | | | | | | | | | | | I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.) have some important flags for booting, "bootnum" and "debugflag". The almost devices have both flags but some devices have only "bootnum" flag. So optimize helper functions in iodata.sh to set each flags. - both: - WN-AX1167GR2 - WN-AX2033GR - WN-DX1167R - WN-DX1200GR - WN-DX2033GR - "bootnum" only - WN-DEAX1800GR Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add wan2 support for MQmaker WiTiArınç ÜNAL2023-07-12
| | | | | | | | | | | | | The PHY of the wan2 port on MQmaker WiTi is wired to the second MAC of the SoC. Rename the wan interface to wan1 and define it under the switch node, effectively disabling the PHY muxing of the MT7530 switch's phy4. Define the PHY of the wan2 port and adjust the gmac1 node accordingly. Now that the PHY muxing feature is not being used anymore, the wan2 port can be used to achieve 2 Gbps total bandwidth to the CPU. Tested-by: Demetris Ierokipides <ierokipides.dem@gmail.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621: add TP-Link EAP613 v1Sander Vanheule2023-07-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ramips: Add support for ComFast CF-E390AXUsama Nassir2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for ComFast CF-E390AX. It is a 802.11 wifi6 cieling AP, based on MediaTek MT7261AT. Specifications: SoC: MediaTek MT7621AT RAM: 128 MiB Flash: 16 MiB NOR (Macronix mx25l12805d) Wireless: MT7915E (2.4G) 802.11ax/b/g/n MT7915E (5G) 802.11ac/ax/n Ethernet: 2 x 1Gbs Button: 1 x "Reset" button LED: 1x Blue LED + 1x Red LED + 1x green LED Power: PoE Manufacturer Page: http://en.comfast.com.cn/index.php?m=content&c=index&a=show&catid=84&id=75 Flash Layout: 0x000000000000-0x000000030000 : "bootloader" 0x000000030000-0x000000040000 : "config" 0x000000050000-0x000000060000 : "factory" 0x000000090000-0x000001000000 : "firmware" First install: 1. Set device into http firmware fail safe upload mode by pressing the reset button for 10 seconds while powering it on. Once the LED stops flashing, safe mode will be running. 2. Set PC IP address to 192.168.1.2 3. Browse to 192.168.1.1 and upload the factory image using the web interface. Signed-off-by: Usama Nassir <usama.nassir@gmail.com>
* ramips: add support for Sercomm S1500 devicesMikhail Zhilkin2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for Netgear EAX12 seriesWenli Looi2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6) extenders that share the SoC, WiFi chip, and image format with the WAX202. Specifications: * MT7621, 256 MiB RAM, 128 MiB NAND * MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC) * Ethernet: 1 port 10/100/1000 * UART: 115200 baud (labeled on board) All LEDs and buttons appear to work without state_default. Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in GPL source: https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz * target/linux/ramips/dts/mt7621-rfb-ax-nand.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ramips: Add support for Beeline SmartBox TURBO+Maximilian Weinmann2023-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router. Device specification -------------------- SoC Type: MediaTek MT7621AT (880 MHz, 2 cores) RAM (Nanya NT5CC64M16GP): 128 MiB Flash (Macronix MX30LF1G18AC): 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615N): a/n/ac, 4x4 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) USB ports: 1xUSB3.0 Buttons: 2 button (reset, wps) LEDs: Red, Green, Blue Zigbee (EFR32MG1B232GG): 3.0 Stock bootloader: U-Boot 1.1.3 Power: 12 VDC, 1.5 A Installation (fw 2.0.9) ----------------------- 1. Login to the web interface under SuperUser (root) credentials. Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the device written on the backplate stick. 2. Navigate to Setting -> WAN. Add: Name - WAN1 Connection Type - Static IP Address - 172.16.0.1 Netmask - 255.255.255.0 Save -> Apply. Set default: WAN1 3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add: Protocol - SSH Port - 22 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN Interface - WAN1 Save ->Apply Add: Protocol - HTTP Port - 80 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN interface - WAN1 Save -> Apply 4. Set up your PC ethernet: Connection Type - Static IP Address - 172.16.0.2 Netmask - 255.255.255.0 Gateway - 172.16.0.1 5. Connect PC using ethernet cable to the WAN port of the router 6. Connect to the router using SSH shell under SuperUser account 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface under admin account 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 171.16.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses (fw 2.0.9) ------------------------ +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:e8 | | WAN | label + 1 | *:e9 | | 2g | label + 4 | *:ec | | 5g | label + 5 | *:ed | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 Factory image format -------------------- +---+-------------------+-------------+--------------------+ | # | Offset | Size | Description | +---+-------------------+-------------+--------------------+ | 1 | 0x0 | 0x200 | Tag Header Factory | | 2 | 0x200 | 0x100 | Tag Header Kernel1 | | 3 | 0x300 | 0x100 | Tag Header Kernel2 | | 4 | 0x400 | SIZE_KERNEL | Kernel | | 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) | +---+-------------------+-------------+--------------------+ Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: fix first boot network configuration for TOZED ZLT S12 PROArınç ÜNAL2023-06-09
| | | | | | | | | | | The network configuration at first boot for TOZED ZLT S12 PRO lacks setting up the LAN and WAN network interfaces. Address this. The WAN port is advertised as WAN/LAN on the device and is put on LAN on stock firmware so put it on LAN here as well. Fixes: ce1f9fa625 ("ramips: add support for TOZED ZLT S12 PRO") Reported-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: enable LED button for TP-Link EC330-G5u v1Mikhail Zhilkin2023-06-08
| | | | | | | | | The device already has LED push button (KEY_LIGHTS_TOGGLE) and exported GPIO control "led-light". This commit adds button handler script for switching on/off all device LEDs. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for TOZED ZLT S12 PROArınç ÜNAL2023-05-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a TOZED TL70-C cellular modem which supports the NCM mode. The stock firmware does SIM locking on the modem by stopping dialing when a different PLMN is detected. This is not the case on OpenWrt. Specifications: - CPU: MediaTek MT7621AT - RAM: 256MB DDR3 - NOR Flash: MX25L12833FM2I 16MB SPI Flash - Wi-Fi 2.4Ghz: MT7603E - Wi-Fi 5Ghz: MT7612E - Switch: MT7530 4x 1Gbit Ports - WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem - USB: 1x optional USB2.0 external port - Switches/Buttons: WPS, Reset, Power Switch - LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone Installation and TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Serial Pins: Located at the bottom right when looking from the front, right under the Reset/WPS buttons. The pinout from the left is: - RX - GND - TX Baudrate is 115200. When connecting from a powered off state, disconnect RX as it blocks the boot process. Link: http://www.sztozed.com/en/contents/58/84.html Co-developed-by: Andre Cruz <me@1conan.com> Signed-off-by: Andre Cruz <me@1conan.com> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for Linksys RE7000Christoph Krapp2023-05-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 16 MB (Macronix MX25L12835FM2I-10G) - RAM: 128 MB (Nanya NT5CC64M16GP-DI) - WLAN 2.4 GHz: 2x2 MediaTek MT7603EN - WLAN 5 GHz: 2x2 MediaTek MT7615N - Ethernet: 1x 10/100/1000 Mbps - LED: Power, Wifi, WPS - Button: Reset, WPS - UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port) Serial console @ 57600,8n1 Flash instructions: Connect to serial console and start up the device. As the bootloader got locked you need to type in a password to unlock U-Boot access. When you see the following output on the console: relocate_code Pointer at: 87f1c000 type in the super secure password: 1234567890 Then select TFTP boot from RAM by selecting option 1 in the boot menu. As Linksys decided to leave out a basic TFTP configuration you need to set server- & client ip as well as the image filename the device will search for. You need to use the initramfs openwrt image for the TFTP boot process. Once openwrt has booted up, upload the sysupgrade image via scp and run sysupgrade as normal. Signed-off-by: Christoph Krapp <achterin@gmail.com>
* ramips: add support for SNR-CPE-ME1Maximilian Weinmann2023-05-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 16 MiB (GD25Q128CSIG) - WLAN : 2.4 GHz (MediaTek MT7603EN) 5 GHz (MediaTek MT7610EN) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (in SoC) - USB : 3.0 x1 - UART : through-hole on PCB - [J4] 3.3V, RX, TX, GND (57600n8) - Power : 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME1 to recovery mode (hold the reset button while power on) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* ramips: mt7621: add support for Cudy X6 v2Felix Baumann2023-05-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename existing device to v1 and create common .dtsi Difference to v1: 16MB Flash Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 16 MB (SPI NOR, XM25QH128C on my device) WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Buttons: Reset, WPS LEDs: Two Power LEDs (blue and red; together they form purple) Power: DC 12V 1A center positive Serial: 115200 8N1 C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2 (P - G - R - T) | v2 labels them on the board Installation: Download and flash the manufacturer's built OpenWrt image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWrt image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 Connect to any lan ethernet port Power on the device while holding the reset button Wait at least 8 seconds before releasing reset button for image to download MAC addresses as verified by OEM firmware: use address source LAN f4:a4:54:86:75:a2 label WAN f4:a4:54:86:75:a3 label + 1 2g f4:a4:54:86:75:a2 label 5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: TP-Link EC330-G5u v1: switch to mac-address-asciiMikhail Zhilkin2023-04-29
| | | | | | | | | | | | | The TP-Link EC330-G5u v1 router has MAC address that stored in factory mtd in ascii format. This commit makes the router use of "mac-address-ascii" in dts. After the change: 1. All MAC addresses are explicitly assigned in dts (the workarounds in network scripts are no longer needed); 2. gmac0 (eth0) MAC address is no longer random. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for D-Link DAP-1620 B1Rani Hod2023-04-29
| | | | | | | | | | | | | | | | | | | | | | | | | The DAP-1620 rev B is a wall-plug AC1300 repeater. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI NOR - MT7615DN 2x2 802.11n +2x2 802.11ac (DBDC) - Ethernet: 1 port 10/100/1000 - Status LEDs (1x red+green) - LED RSSI bargraph (2x green, 1x red+green) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tail -c+117 DAP1620B1_FW212B03.bin | \ openssl aes-256-cbc -d -md md5 -out decrypted.bin \ -k 905503a4e0c3cd3c1ce062246de427a68962347e - flash decrypted.bin via D-Link Web Recovery Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ramips: mt7621: add support for ZyXEL WSM20Andreas Böhler2023-04-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL based on the MT7621 CPU. Specifications ============== SoC: MediaTek MT7621AT (880MHz) RAM: 256MiB Flash: 128MiB NAND Wireless: 802.11ax (2x2 MT7915E DBDC) Ethernet: 4x 10/100/1000 (MT7530) Button: 1x WPS, 1x Reset, 1x LED On/Off LED: 7 LEDs (3x white, 2x red, 2x green) MAC address assignment ====================== The MAC address assignment follows stock: The label MAC address is the LAN MAC address, the WAN address is read from flash. The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC + 2. Installation (web interface) ============================ The device is cloud-managed, but there is a hidden local firmware upgrade page in the OEM web interface. The device has to be registered in the cloud in order to be able to access this page. The system has a dual firmware design, there is no way to tell which firmware is currently booted. Therefore, an -initramfs version is flashed first. 1. Log into the OEM web GUI 2. Access the hidden upgrade page by navigating to https://192.168.212.1/gui/#/main/debug/firmwareupgrade 3. Upload the -initramfs-kernel.bin file and flash it 4. Wait for OpenWrt to boot and log in via SSH 5. Transfer the sysupgrade file via SCP 6. Run sysupgrade to install the image 7. Reboot and enjoy NB: If the initramfs version was installed in RAS2, the sysupgrade script sets the boot number to the first partition. A backup has to be performed manually in case the OEM firwmare should be kept. Installation (UART method) ========================== The UART method is more difficult, as the boot loader does not have a timeout set. A semi-working stock firmware is required to configure it: 1. Attach UART 2. Boot the stock firmware until the message about failsafe mode appears 3. Enter failsafe mode by pressing "f" and "Enter" 4. Type "mount_root" 5. Run "fw_setenv bootmenu_delay 3" 6. Reboot, U-Boot now presents a menu 7. The -initramfs-kernel.bin image can be flashed using the menu 8. Run the regular sysupgrade for a permanent installation Changing the partition to boot is a bit cumbersome in U-Boot, as there is no menu to select it. It can only be checked using mstc_bootnum. To change it, issue the following commands in U-Boot: nand read 1800000 53c0000 800 mw.b 1800004 1 1 nand erase 53c0000 800 nand write 1800000 53c0000 800 This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to change to the second slot. Back to stock ============= It is possible to flash back to stock, but a OEM firmware upgrade is required. ZyXEL does not provide the link on its website, but the link can be acquired from the OEM web GUI by analyzing the transferred JSON objects. It is then a matter of writing the firmware to Kernel2 and setting the boot partition to FW2: mtd write zyxel.bin Kernel2 echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc Signed-off-by: Andreas Böhler <dev@aboehler.at> Credits to forum users Annick and SirLouen for their initial work on this device
* ramips: Cudy X6 fixes / improvementsFelix Baumann2023-04-24
| | | | | | | | | | | | | | | | | | | | | | - Correct WiFi MACs, they didn't match oem firmware - Move nvmem-cells to bdinfo partition and remove &bdinfo reference - Add OEM device model name R13 to SUPPORTED_DEVICES This allows sysupgrading from Cudy's OpenWrt fork without force - Label red_led and use it during failsafe mode and upgrades MAC addresses as verified by OEM firmware: use address source LAN b4:4b:d6:2d:c8:4a label WAN b4:4b:d6:2d:c8:4b label + 1 2g b4:4b:d6:2d:c8:4a label 5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased The label MAC address is found in bdinfo 0xde00. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [read wifi mac from flash offset] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: MSG1500 X.00: switch to mac-address-ascii dtsChukun Pan2023-04-21
| | | | | | | | The Config partition of some machines is special, and the openwrt script cannot read the protest_lan_mac correctly. This problem can be solved by reading the mac address (ascii) in dts. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: mt7621: add migration script for WLAN PCI pathsFelix Baumann2023-04-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PCI paths of the WLAN devices have changed between kernel 5.10 and 5.15; migrate config so existing wifi-iface definitions don't break. This is implemented as a hotplug handler rather than a uci-defaults script as the migration script must run before the 10-wifi-detect hotplug handler. based on b452af23a8602ebf7bfb0eb084383ecd595face5 migration was forgotten when device trees were adjusted in 688697889c9ceb9d2d8d413d1abcc5fa7edb402b c77913be5be5f11a0f20dba1b45b96470099e8a8 fixes #9374 affected devices: Netgear R6220 Netgear WAC104 Netgear WNDR3700 v5 Zbtlink ZBT-WE1326 Wiflyer WF3526-P Arcadyan WE420223-99 Beeline Smartbox Flash (Arcadyan WG443223) MTS WG430223 (Arcadyan WG430223) Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com> Tested-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621: remove set-affinity scriptRosen Penev2023-04-01
| | | | | | | | | | | | From https://github.com/openwrt/openwrt/pull/12280#issuecomment-1489279860 On Ethernet and WLAN, NAPI is threaded for all queues. This means that the processing work is not stuck on the CPU that fired the IRQ. Under heavy load, IRQs get disabled anyway, so it should not matter at all which CPUs the IRQs fire on. Basic testing indicates this to be true. There's no speedup or slowdown. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: fix 5g mac for TOTOLINK X5000RChuanhong Guo2023-03-26
| | | | | | | | | There's no valid mac address for the second band in the eeprom. The vendor fw uses 2.4G mac + 4 as the mac for 5G radio. Do the same in our firmware. Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for Mercusys MR70XDavid Bauer2023-03-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== - SoC: MediaTek MT7621AT (880MHz, Duel-Core) - RAM: DDR3 128MB - Flash: Winbond W25Q128JV (SPI-NOR 16MB) - WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC) - Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC) - UART: >TX RX GND 3v3 (115200 8N1, J1) Do not connect 3v3. TX is marked with an arrow. Installation ============ Flash factory image. This can be done using stock web ui. Revert to stock firmware ======================== Flash stock firmware via OEM Web UI Recovery mode. Web UI Recovery method ====================== 1. Unplug the router 2. Plug in and hold reset button 5~10 secs 3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0 4. Flash image with web browser to 192.168.1.1 Co-authored-by: Robert Senderek <robert.senderek@10g.pl> Co-authored-by: Yoonji Park <koreapyj@dcmys.kr> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix Archer AX23 WiFi MAC address conflictDavid Bauer2023-03-21
| | | | | | | | | | The original claim about conflicting MAC addresses is wrong. mac80211 does increment the first octet and sets the LA bit. This means our "workaround" actually leads to the issue while incrementing the last octet is safe. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link Archer AX23 v1David Bauer2023-03-15
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR () WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Upload the factory image using the Web-UI. Web-Recovery ------------ The router supports a HTTP recovery mode by holding the reset-button when powering on. The interface is reachable at 192.168.0.1 and supports installation using the factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for SNR-CPE-ME2-SFPAleksey Nasibulin2023-03-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company. Specification: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB (GD25Q127CSIG) - RAM: 256 MB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN) - Ethernet: 4x 10/100/1000 Mbps - SFP cage (using RTL8211FS-CG) - USB 3.0 port - Power: 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME2 to recovery mode (press reset button and power on device, hold button for ~10 seconds) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 6A:C4:DD:xx:xx:28 | | Ethernet | + 1 | 6A:C4:DD:xx:xx:29 | | 2g | + 2 | 6A:C4:DD:xx:xx:2A | | 5g | + 3 | 6A:C4:DD:xx:xx:2B | +----------+------------------+-------------------+ Notes: - Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation. References: 1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249 Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
* ramips: mt7621: TP-Link EAP235/615-Wall: add poe passthrough gpio definitionsAndré Fonseca2023-03-04
| | | | | | | | | Add the missing definitions for the PoE passthrough functionality. The relevant pin is already being exported, but it is missing from the initial board configuration file. With this change, the user is now able to toggle the PoE passthorough functionality via the uci cli Signed-off-by: André Fonseca <mail@andrefonseca.pt>
* ramips: add support for D-Link Dir-853 A1Hang Zhou2023-03-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MT7621AT * RAM: 256MB (NT5CC64M16GP-DI) * Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver) * WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC * Ethernet: 4x1000M LAN, 1x 1000M WAN * LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue * Buttons: Reset,WPS, Wifi * Serial interface: on board but not populated, pinout (from the DC jack side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600, settings are 8 data bits, no parity bit, one stop bit, and no flow control. Stock flash layout: ``` GD25Q128C(c8 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 7 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "Config2" 0x000000060000-0x000000fb0000 : "Kernel" 0x000000fb0000-0x000001000000 : "Private" ``` The kernel partition will be replaced with the OpenWrt image, the other partitions are left untouched. "Config2" seems to be the config storage used by the stock firmware. "Private" is a 320kB empty JFFS2 partition that comes with the stock firmware. One can get a larger space for OpenWrt by merging it with "Kernel". OpenWrt flash layout: ``` 0x000000000000-0x000000030000 : "u-boot" 0x000000030000-0x000000040000 : "u-boot-env" 0x000000040000-0x000000050000 : "factory" 0x000000050000-0x000000060000 : "config2_stock" 0x000000060000-0x000000fb0000 : "firmware" 0x000000fb0000-0x000001000000 : "private_stock" ``` The OpenWrt image must have 96 bytes of padding in the header. MAC addresses on OEM firmware: | | location on the flash | notes | |------ |----------------------- |---------- | | lan (eth2) | factory + 0xe000 | on label | | wan (eth3) | factory + 0xe006 | | | 2.4g (rax0) | not on flash | lan + 1 | | 5g (ra0) | not on flash | lan + 2 | Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in the u-boot-env partition, but they are not used. OpenWrt calculates Wifi Mac addresses based on the LAN Mac. Flash and test instructions: Flash the encrypted image (available in the OpenWrt forum) through the stock D-Dink web interface. 1. Open the case, and solder the 4-pin header near the WAN port. 2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC. 3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with the settings mentioned above. 4. Setup a TFTP server on your PC that can serve `xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`. 5. Connect any LAN port to your PC and set a static IPv4 address to 192.168.0.101 (netmask 255.255.255.0). 6. Power on the device and keeps pressing 1 until you see the prompt. 7. Use default IP addresses and enter the file name accordingly, then hit enter. 8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1, you need to change your PC network adapter to use DHCP in order to access LUCI. 9. So far, the OpenWrt runs in RAM and the flash contents are not touched. You can try OpenWrt without having to overwrite the stock firmware, a reboot clears all changes. 10. Optionally, backup the stock firmware (the "firmware" partition) in Luci. 11. To permantly install OpenWrt to the device , click on "System -> Backup/Flash Firmware" in Luci and flash `xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin` Known problems: * WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network, you need to config it manually in LUCI. * If you see jffs2 related warnings/errors after updating from the stock web interface, you need to do a reset in LUCI. The error will be gone after a cold reboot. Signed-off-by: Hang Zhou <929513338qq@gmail.com>
* ramips: add support for Huasifei WS1208V2Arınç ÜNAL2023-02-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Huasifei WS1208V2 is an AC1200 router featuring 5 Ethernet ports with a Quectel RM520N-GL cellular modem which supports QMI and MBIM modes. Specifications: - MT7621AT, 256 MiB RAM, 16 MiB SPI Flash - MT7603EN 2.4 GHz & MT7612EN 5 GHz WLAN - Quectel RM520N-GL Cellular Modem - 2 WLAN & 4 Cellular Antennas - 5 Gigabit Ethernet Ports - 1 USB 2.0 port - 1 PCI-E Slot - 1 M.2 slot - 1 SIM card slot - 1 SD card slot Installation: - Install sysupgrade image via ROOter OS. TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Link: https://www.huasifei.com/a/Products/5G%20CPE/240.html Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: add support for ASUS RT-AX54Karl Chan2023-02-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX54 (AX1800S/HP,AX54HP) - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 4 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x POWER (blue, configurable) 1x LAN (blue, configurable) 1x WAN (blue, configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Karl Chan <exkc@exkc.moe>
* ramips: add support for TP-Link Deco M4R v4Mark Ceeha2023-02-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the V4 hardware revision of the Deco M4R. V4 is a complete overhaul of the hardware compared to V1 and V2, and is much more similar to the Archer C6 V3 and C6U V1. Specifications: SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads) RAM: Kingston D1216ECMDXGJD (256 MB) Wireless 2.4 GHz: MediaTek MT7603EN Wireless 5 GHz: MediaTek MT7613BEN Flash: 16 MB SPI NOR Installation: Flash the *-factory.bin image in the U-Boot recovery webserver. You can trigger this webserver by holding the reset button until the LED flashes yellow, or by hooking up to serial pads on the board (clearly labeled GND, RX and TX) and pressing `x` early in boot. Once the factory image has been flashed, you can use the regular upgrade procedure with sysupgrade images for subsequent flashes. Signed-off-by: Mark Ceeha <hi@shiz.me> Tested-by: Mark Ceeha <hi@shiz.me>
Powered by cgit, Themed by Ted Yin.