aboutsummaryrefslogtreecommitdiff
path: root/target/linux/mpc85xx/base-files/lib
Commit message (Collapse)AuthorAge
* Revert "mpc85xx: replace user space MAC with nvmem"Christian Marangi2023-11-21
| | | | | | | | | This reverts commit 931fcf61891f14dffccd0ad5dfdf7d84460ff9f2. The definition is wrong and require mac-base compatible. Also it's not clear if it's correct to use 0xc for mac size. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mpc85xx: replace user space MAC with nvmemRosen Penev2023-11-21
| | | | | | Possible now that NVMEM supports ASCII. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mpc85xx: add support for Enterasys WS-AP3715iDavid Bauer2023-04-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1010 (1x e500 @ 800MHz) RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9) FLASH: 32M NOR (Spansion S25FL256S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035) UART: 115200 8N1 (RJ-45 Cisco) Installation ------------ 1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in the root directory of a TFTP server and serve it at 192.168.1.66/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Alter the bootcmd in U-Boot: $ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm" $ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000; bootm 0x2000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Boot the initramfs image $ run ramboot_openwrt 5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Signed-off-by: David Bauer <mail@david-bauer.net>
* Revert "mpc85xx: remove Watchguard T10 MAC override"David Bauer2023-04-03
| | | | | | | | | | This reverts commit aa4a9058fbf4d2ca7ef3af9ebb5bbec896625e93. The assumption the bootloader fills out the MAC-address is not correct. The MAC-address has to be set from userspace based on information found in the device_id partition. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove Watchguard T10 MAC overrideDavid Bauer2023-03-20
| | | | | | | | As the mac-address readout never worked, the mac-address fillout by the bootloader is sufficient. Remove the readout for the Watchguard T10 then. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: fix missing system importDavid Bauer2023-03-20
| | | | | | | The mac-address accessor functions were not included in the sourced script. Fix this by importing the correct script path. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Watchguard Firebox T10David Bauer2023-03-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Freescale P1010 RAM: 512MB FLASH: 1 MB SPI-NOR 512 MB NAND ETH: 3x Gigabite Ethernet (Atheros AR8033) SERIAL: Cisco RJ-45 (115200 8N1) RTC: Battery-Backed RTC (I2C) Installation ------------ 1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI programmer. The SHA1 hash for the U-Boot password is currently unknown. A tool for patching U-Boot is available at https://github.com/blocktrron/t10-uboot-patcher/ You can also patch the unknown password yourself. The SHA1 hash is E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA 2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears. The patched password is '1234' (without quotation marks) 3. Download the OpenWrt initramfs image. Copy it to a TFTP server reachable at 10.0.1.13/24 and rename it to uImage. 4. Connect the TFTP server to ethernet port 0 of the Watchguard T10. 5. Download and boot the initramfs image by entering "tftpboot; bootm;" in U-Boot. 6. After OpenWrt booted, create a UBI volume on the old data partition. The "ubi" mtd partition should be mtd7, check this using $ cat /proc/mtd Create a UBI partition by executing $ ubiformat /dev/mtd7 -y 7. Increase the loadable kernel-size of U-Boot by executing $ fw_setenv SysAKernSize 800000 8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using scp. Install the image by using sysupgrade: $ sysupgrade -n <path-to-sysupgrade> Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might have to change the ethernet-port. 9. OpenWrt should now boot from the internal NAND. Enjoy. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: set WS-AP3825i mac-address in preinitDavid Bauer2022-04-26
| | | | | | | | | The bootloader does seem to not correctly patch in the MAC address for eth0 / eth1 in some cases. While the root cause is not known, manually applying the MAC-Address in preinit does not hurt. Reported-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-16
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-17
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mpc85xx: add support for OCEDO PandaDavid Bauer2019-01-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: FSL P1020 (2x 800MHz E500 PPC) RAM: 1GB DDR3 FLASH: 256MiB NAND WiFi: 2x Atheros AR9382 2x2:2 abgn ETH: 2x BCM54616S - 1x BCM53128 8-port switch LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS) BTN: 1x RESET Installation ------------ 1. Download initrams kernel image, dtb binary and sysupgrade image. 2. Place initramfs kernel into tftp root directory. Rename to "panda-uimage-factory". 3. Place dtb binary into tftp root directory. Rename to "panda.fdt". 4. Start tftp server on 192.168.100.8/24. 5. Power up the device with the reset button pressed. It will download the initrams and dtb via tftp and boot into OpenWRT in RAM. 6. SSH into the device and remove the factory partitions. > ubirmvol /dev/ubi0 --name=kernel1 > ubirmvol /dev/ubi0 --name=rootfs1 > ubirmvol /dev/ubi0 --name=devicetree1 You will have around 60 MiB of free space with that. You can also delete "kernel2", "devicetree2", "rootfs2" and "storage" respectively in case you do not want to go back to the vendor firmware. 7. Modify the U-Boot bootcmd to allow for booting OpenWRT > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel && bootm 0x1000000" > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200 ubi.mtd=3,2048" > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt" 8. Transfer the sysupgrade image via scp into the /tmp directory. 9. Upgrade the device > sysupgrade -n /tmp/<imagename> Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Sophos RED 15w Rev.1David Bauer2019-01-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: remove obsolete sysupgrade watchdog killMathias Kresin2018-02-16
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: use image metadataMathias Kresin2017-10-25
| | | | | | | Append and enforce image metadata. Remove the device specific image checks, they are replaced by image metadata. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: use the generic board detectMathias Kresin2017-10-25
| | | | | | | | | | | | Use the values populated by the generic board detect function. The first compatible from the device tree source file will be the board name in userspace. The model property from the device tree source file will be the model name. Change the board name where used in the userspace and drop the target specific board detect, to use the generic one. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: update HiveAP-330 dtsChris Blake2017-10-25
| | | | | | | | | | | | | | | | | | | initramfs is not the proper name for this, as it stores a boot ramdisk and not a filesystem. Update the name to reflect it's usage correctly. If CMDLINE_OVERRIDE is enabled, the chosen bootargs aren't used at all. Drop them from the device tree source file to not cause confusion. Remove the noinitrd bootarg. Due to the empty ramdisk this parameter isn't required any longer: [ 0.000000] Initrd not found or empty - disabling initrd Use the LEDE mtd-mac-address* device tree properties to set the interfaces MAC-Addresses. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: Add Aerohive HiveAP-330 Access PointChris Blake2017-10-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive HiveAP-330 Access Point to LEDE under the mpc85xx/p1020 subtarget. Hardware: - SoC: Freescale P1020NSE2DFB - NAND: Intel JS28F512M29EWH 64MB - Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - 5.0GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - Eth2: Atheros AR8035-A - TPM: Atmel AT97SC3204 - LED Driver: TI LP5521 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; tftpboot 0x1000000 192.168.1.101:lede- mpc85xx-p1020-hiveap-330-initramfs.zImage; tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt; bootm 0x1000000 - 0x6000000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NAND. sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* treewide: drop target board_name functionsMathias Kresin2017-07-15
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-15
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: populate boardname and model earlierMathias Kresin2017-07-15
| | | | | | | | | | | | | For targets using the generic board detection and board specific settings in diag.sh, the board name is still unset at the time the set_state() provided by diag.sh is called by 10_indicate_preinit. Change the execution order to ensure the boardname is populated before required the first time. Do the target specific board detection as early as possible, directly followed by the generic one to allow a seamless switch to the generic function for populating /tmp/sysinfo/. Signed-off-by: Mathias Kresin <dev@kresin.me>
* target/linux/*/base-files/lib/upgrade/platform.sh - wrong check for ARGCJohn Crispin2014-06-02
| | | | | | | | | | | | | | | | | | | ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct var $# (=number of args) here. under normal conditions this had no impact, but we should at least correct it. the error was observable like this: root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh root@box:~ . /lib/upgrade/platform.sh root@box:~ . /lib/upgrade/common.sh root@box:~ platform_check_image /tmp/myfirmware.bin ash: bad number root@box:~ echo $? 0 Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com> SVN-Revision: 40915
* base-files: input/button drivers get loaded before preinit by procdJohn Crispin2013-06-21
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37000
* mpc85xx: set preinit interface to eth0 by defaultGabor Juhos2013-04-12
| | | | | | | | | This makes the WDR4900 accessible via ethernet in failsafe mode. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36322
* mpc85xx: add user-space support for the TL-WDR4900 v1Gabor Juhos2013-02-21
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35733
* mpc85xx: add input drivers to default packages, and load those during preinitGabor Juhos2013-02-16
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35626
Powered by cgit, Themed by Ted Yin.