aboutsummaryrefslogtreecommitdiff
path: root/target/linux
Commit message (Collapse)AuthorAge
...
* qualcommax: ipq60xx: Add 8devices Mango DVKMantas Pucka2024-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com>
* qualcommax: ipq60xx: set correct PHY mode for port 0-4Mantas Pucka2024-02-21
| | | | | | | | | | | | | | [port 8ed390a (qualcommax: set correct PHY mode for port 0-4) to ipq60xx] Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use he upstream qca807x driver, this conflicts with the qca SSDK driver that expects the mode to be PSGMII as for not integrated driver, it does refer to the real PHY mode. Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK in ipq6018-ess.dtsi. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* qualcommax: ipq807x: skip factory.ubi image for MX4200Paweł Owoc2024-02-21
| | | | | | Skip building not used factory.ubi image Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
* qualcommax: ipq807x: remove duplicated sysupgrade image definitionsPaweł Owoc2024-02-21
| | | | | | Image sysupgrade.bin is defined by default and there is no need to define it. Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
* qualcommax: ipq807x: fix variable definitionPaweł Owoc2024-02-21
| | | | | | | | Fix variable definition, prevent displaying warnings: - warning: overriding recipe for target - warning: ignoring old recipe for target Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
* ramips: clean up useless dts partition labelsShiji Yang2024-02-21
| | | | | | | | | | The previous NVMEM eeprom conversions[1][2] left a lot of partition labels that were no longer used. They can be removed now. [1] https://github.com/openwrt/openwrt/pull/13584 [2] https://github.com/openwrt/openwrt/pull/13587 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* rockchip: add Radxa CM3 IO board supportMarius Durbaca2024-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3566 ARM64 (4 cores) - up to 8GB LPDDR4X - 1x HDMI, - 2x MIPI DSI - 2x MIPI CSI2 - 1x eDP - 1x PCIe card - 2x SATA - 2x USB 2.0 Host - 1x USB 3.0 - 1x USB 2.0 OTG - 10/100/1000 Base-T - microSD slot - 40-pin GPIO expansion header - 12V DC Radxa CM3 needs to mount on top of this IO board in order to create complete Radxa CM3 IO board platform. Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org> Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
* generic: replace simple AQR hack patch with upstream versionChristian Marangi2024-02-21
| | | | | | | | | Simple AQR hack patch has been merged upstream, hence we can drop it from hack directory and move it to backport. The patch for 5.15 are correctly reworked to align to outdated API. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mediatek: filogic: fix mt7981 DT nodenamesRafał Miłecki2024-02-20
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: filogic: improve mt7981 DT coding styleRafał Miłecki2024-02-20
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: filogic: reorder mt7981 DT propertiesRafał Miłecki2024-02-20
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: filogic: reorder mt7981 DT SoC reg-based nodesRafał Miłecki2024-02-20
| | | | | | | Follow upstream Linux kernel guidelines: https://www.kernel.org/doc/html/next/devicetree/bindings/dts-coding-style.html#order-of-nodes Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: filogic: reorder mt7981 DT name-based nodesRafał Miłecki2024-02-20
| | | | | | | Follow upstream Linux kernel guidelines: https://www.kernel.org/doc/html/next/devicetree/bindings/dts-coding-style.html#order-of-nodes Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* generic: 6.1: add missing symbol for EN8811H PHY driverRobert Marko2024-02-19
| | | | | | | Disable Airoha EN8811H PHY driver by default to avoid individual targets having to disable it. Signed-off-by: Robert Marko <robimarko@gmail.com>
* rockchip: add NanoPi R4S Enterprise Edition buildTianling Shen2024-02-19
| | | | | | | | | | | FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address) to "enterprise" edition, and it was added as a "new" board in upstream kernel. This patch switched to use that upstreamed dts and removed local EEPROM patch. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: update WA/XC devices UBNT_VERSION to 8.7.4Martin Garbe2024-02-19
| | | | | | | | | | Ubiquiti WA devices with newer hw version (sold 2023) require UBNT_VERSION to be at least 8.7.4, otherwise the image is rejected. For consistency, also increase version number for XC devices. Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
* rockchip: add NanoPi R2C Plus supportTianling Shen2024-02-19
| | | | | | | | | | | | The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board eMMC flash (8G) included. Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* qualcommax: backport more changes for ipq6018 and ipq8074Chukun Pan2024-02-19
| | | | | | | | - Mark patches as upstream - Backport more upstream changes - Handle conflicts and refresh patches Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DTRafał Miłecki2024-02-19
| | | | | | | It's a standard way of grouping on-SoC hardware blocks and this matches upstream DTS. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: filogic: fix nvmem cell names of the GL.iNet MT-2500Daniel Golle2024-02-19
| | | | | | | Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500. Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)" Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* imx: remove 5.15 supportKoen Vandeputte2024-02-18
| | | | | | Drop all 5.15 files as 6.1 is the default now Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* imx: switch to kernel 6.1Koen Vandeputte2024-02-18
| | | | | | | I have this kernel running for weeks some on a lot of boards in multiple scenarios Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* kernel: bump 6.1 to 6.1.78John Audia2024-02-18
| | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.78 Manually rebased: bcm27xx/patches-6.1/950-0865-usb-dwc3-Set-DMA-and-coherent-masks-early.patch bcm27xx/patches-6.1/950-0124-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch All other patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, logic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, logic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mvebu: drop kernel 5.15 config and patchesStefan Kalscheuer2024-02-18
| | | | | | With default now being at 6.1 we can remove all 5.15 components. Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* mvebu: switch to kernel 6.1Stefan Kalscheuer2024-02-18
| | | | | | After a few months of testing it's time to move to 6.1 by default. Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* realtek: fix Netgear GS110TPP OEM installBjørn Mork2024-02-18
| | | | | | | | | | | | | | | | | | | | Recent OEM firmware versions test the version number embedded in the uimage "name" header field. The exact restricton is unknown, but "7.0.8.4" seems to be the lowest number accepted on a GS110TPPv1 which already has that version or higher. A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware, and considered both unique enough to identify an OpenWrt image and moderately future proof against OEM version bumps. This change is also boot tested on a GS108Tv3 with "BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)" to verify that it doesn't break boot on older hardware. Link: https://forum.openwrt.org/t/72510/58 Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMCDaniel Golle2024-02-18
| | | | | | | Use nvmem-layout in device tree instead of extracting MAC addresses in userspace. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7981: remove inaccurate compatible stringsDaniel Golle2024-02-18
| | | | | | | Remove more inaccurate compatible strings from various clock controllers of the MT7981 SoC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7981: prevent system freezes on bootDaniel Golle2024-02-18
| | | | | | | | Import patch to make sure SGM_REG_SEL clock is always enabled as it seems that more registers than just SGMIISYS0 and SGMIISYS1 are depending on that clock being enabled. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: convert GL.iNet MT-6000 to NVMEM-on-MMCDaniel Golle2024-02-18
| | | | | | | Now that we can reference MMC partitions in device tree, use that to get rid of Wi-Fi EEPROM and MAC address setup in userspace. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: nvmem: correctly assign fwnode to MMC block deviceDaniel Golle2024-02-18
| | | | | | | | | | Use device_set_node to make sure OF node gets assigned on block devices to be used as NVMEM providers. While block partitions were already working fine as NVMEM providers, bare block devices such as mmcblk0boot1 will not work without this change. Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* qualcommax: ipq807x: wax630: correct UNIPHY2 MAC modeRobert Marko2024-02-17
| | | | | | | | UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and it does not support using USXGMII at all but rather only SGMII or SGMII+. Tested-by: Kristian Skramstad <kristian+github@83.no> Signed-off-by: Robert Marko <robimarko@gmail.com>
* mediatek: dts: mt7981: fix ethsys clock compatibleDaniel Golle2024-02-17
| | | | | | | | | | Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which results in the wrong clock driver probing on MT7981 with Linux 6.1 and ends up freezing the system once WED is used. Fixes: da970d63fb ("mediatek: switch to Linux version 6.1") Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: replace built-in Aquantia driver with moduleRafał Miłecki2024-02-17
| | | | | | | | | | | | | Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by host system. With built-in drivers this doesn't work in OpenWrt / embeddded as filesystem isn't available during PHY probe. That results in delays like: [ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld [ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110) Switch to module to postpone PHY probe to init state. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* qualcommax: ipq807x: correct PHY mode for AQRRobert Marko2024-02-17
| | | | | | | | | | | | | | Interfaces that have AQR-s attached to them are using USXGMII and not just the default SGMII. This was fine until SSDK added some sanity checking and now on Qnap 301W it would fail with: [ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device [ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14 Since this is not Qnap 301W specific lets fix it subtarget wide by declaring the correct PHY mode for 10G AQR-s. Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq807x: 301w: correct PHY mode for AQRRobert Marko2024-02-17
| | | | | | | | | | | | | Interfaces that have AQR-s attached to them are using USXGMII and not just the default SGMII. This was fine until SSDK added some sanity checking and now on Qnap 301W it would fail with: [ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device [ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14 So, lets fix 10G AQR ports by declaring the correct PHY mode. Signed-off-by: Robert Marko <robimarko@gmail.com>
* mediatek: mt7622: skip build also for Xiaomi AX6SDaniel Golle2024-02-17
| | | | | | | Also here build fails due to increased kernel size. Fixes: da970d63fb ("mediatek: switch to Linux version 6.1") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: skip build for MT7622 rfb1 (UBI)Daniel Golle2024-02-17
| | | | | | | | | | Due to increased kernel size the build currently fails if including the MT7622 rfb1 (UBI). Skip it for now until there is a better solution (such as replacing the bootloader and changing the flash layout). Fixes: da970d63fb ("mediatek: switch to Linux version 6.1") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: include kmod-phy-airoha-en8811hDaniel Golle2024-02-17
| | | | | | | | Include the needed Ethernet PHY driver module for the BananaPi R3 mini. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Reported-by: BPI forum user nezar_taima Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: fix power on M.2 slotTianling Shen2024-02-16
| | | | | | | | | | One of the pins requiered by M.2 slot is conflict with spi1, however, spi1 seems unused so simply disable it for now, this matches the factory behavior [1]. 1. https://github.com/BPI-SINOVOIP/BPI-R3MINI-OPENWRT-V21.02.3/commit/9bd78779f267a21c04c5bb4d16c32e83aae8d1d3 Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: bpi-r3-mini: bind WLAN LED-s to phy*-ap0Tianling Shen2024-02-16
| | | | | | For showing wlan status. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: bpi-r3-mini: convert to new LED color/function formatTianling Shen2024-02-16
| | | | | | | | | | Conversion to new LED color/function format and drop label format. This was needed previously when the new format wasn't supported by leds.sh functions script. Now that is supported this property can be removed in favor of the new format. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: generic: fix the alphabetical order in 02_networkFoica David2024-02-16
| | | | | | | This commit fixes the alphabetical order in 02_network. The 2 deco devices in ath79_setup_interfaces() were in the wrong place. Signed-off-by: Foica David <superh552@gmail.com>
* qualcommax: AW1000: add qca8081 PHY LED configurationChukun Pan2024-02-16
| | | | | | | | Since we can configure the PHY LED of the qca8081, add a configuration for this device. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
* qualcommax: AW1000: sync qca807x PHY dts changesChukun Pan2024-02-16
| | | | | | | | | The dts of Arcadyan AW1000 forgot to convert qca807x PHY to PHY package implementation. This commit fix it. Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
* mediatek: filogic: bpi-r3-mini: fix generating ubinized imageDaniel Golle2024-02-16
| | | | | | | | Generate ubinized image as ARTIFACT and make use of now available generic 'ubinize-image' build step intended for that purpose. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: fix NAND flash layoutDaniel Golle2024-02-16
| | | | | | | | Fix NAND flash layout which was out-of-sync with the definition in ARM TrustedFirmware-A which expects UBI to start at 0x200000. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt76x8: fix build due to renamed U-Boot binaryDaniel Golle2024-02-16
| | | | | | | | | The U-Boot binary for the RAVPower RP-WD009 has been renamed. In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended. Set that new name also in the image build recipe for that device in order to fix build. Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* imx: update default network config for ventanaTim Harvey2024-02-15
| | | | | | | | update the default network configuration for Gateworks Ventana boards such that the left-most front-panel NIC is WAN and any additional are in LAN bridge Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx: add gpio-button-hotplug to ventana imagesTim Harvey2024-02-15
| | | | | | | Add the gpio-button-hotplug to Gateworks ventana images to support the on-board user pushbutton. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Powered by cgit, Themed by Ted Yin.