| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
| |
As preparation for the arm926ej-s support which has a different
load address, move the KERNEL_LOADADDR into the subtargets.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Key features:
Allwinner H618 SoC (Quad core Cortex-A53)
1/1.5/2/4 GiB LPDDR4 DRAM
1 USB 2.0 type C port (Power + OTG)
1 USB 2.0 host port
1Gbps Ethernet port
Micro-HDMI port
MicroSD slot
Installation:
Write the image to SD Card with dd.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
SoC: Allwinner H616 @ 1.5 Ghz
DRAM: 1Gb LPDDR3
Power: 5V USB-C
Video: HDMI (Type 2.0A - micro)
Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi
Storage: microSD / 2Mb SPI flash
USB: 1 USB2.0 Host
Debug Serial UART
Flashing instructions:
Standard sunxi SD card installation procedure - copy image to SD card,
insert into SD card slot on the device and boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
|
| |
|
|
|
|
|
|
| |
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.
Fixes: 397dfe4a97e6 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specification:
CPU: Allwinner H5, Quad-core Cortex-A53
DDR3 RAM: 512MB
Network: 10/100/1000M Ethernet x 2
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input
Debug Serial Port: 3Pin pin-header
LED: WAN, LAN, SYS
KEY: Reset
Power Supply: DC 5V/2A
Installation:
Write the image to SD Card with dd.
Note:
1. OpenWrt currently does not support LED_FUNCTION, change back to the
previous practice (Consistent with NanoPi R1).
2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
change the phy-mode from rgmii to rgmii-id.
So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
SoC Allwinner H6 @ 1.8 Ghz
DRAM 1Gb LPDDR3
Power DC 5V @ 3A
Video HDMI (Type 2.0A - full)
Audio HDMI, on-board microphone
Network 10/100/1000Mbps Ethernet (Realtek RTL8211)
Storage microSD
USB 1 USB2.0 Host, 1 USB2.0 OTG
Debug Serial UART
Flashing instructions:
Standard sunxi SD card installation procedure - copy image to SD card,
insert into SD card slot on the device and boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi
module, carrying an RTL8723BS. The wifi part is connected via
SDIO, the BT part is connected via UART. The BT part requires
additional code changes in the drivers so we'll skip that until 5.10.
Aside from a DTS patch to enable the wifi module, add the required
packages into the device definitions.
[ 8.996970] RTL8723BS: module init start
[ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[ 9.014785] pnetdev = 000000009bdd5000
[ 9.047780] RTL8723BS: rtw_ndev_init(wlan0)
[ 9.053349] RTL8723BS: module init ret =0
root@OpenWrt:/# iw list
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 9
max scan IEs length: 2304 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* monitor
Band 1:
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (no IR)
* 2472 MHz [13] (20.0 dBm) (no IR)
* 2484 MHz [14] (20.0 dBm) (no IR)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
|
| |
|
|
|
|
| |
Use SPDX license tags to allow machines to check licenses.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specification:
- CPU: Allwinner H5, Quad-core Cortex-A53 Up to 1GHz
- DDR3 RAM: 2GB
- Network:
10/100M Ethernet x 1
- IR: x1 (Receive)
- USB (Host) Type-A x3
- USB (OTG) Type-A x1
- MicroSD Slot x 1
- eMMC Slot x1
- MicroUSB power input
- GPIO 40pin header
- UART 3pin header
- Leds:
- librecomputer:blue:status
- librecomputer:green:pwr
- Buttons:
- uboot button (used to enter fel mode)
- power button (can trigger power on)
- Power Supply via MicroUSB or GPIO 5V/2A
Installation:
- Write the image to SD Card with dd
- Boot from the SD Card
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
[Fixed Signed-off-by]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|