aboutsummaryrefslogtreecommitdiff
path: root/target/linux/sunxi/image/cortex-a53.mk
Commit message (Collapse)AuthorAge
* treewide: simplify inclusion of subtarget image filesAdrian Schmutzler2020-06-11
| | | | | | | | | | | | | | Many target use a repetitive if-include scheme for their subtarget image files, though their names are consistent with the subtarget names. This patch removes these redundant conditions and just uses the variable for the include where the target setup allows it. For sunxi, this includes a trivial rename of the subtarget image Makefiles. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: a53: add support for Olimex A64-Olinuxino eMMCPetr Štetiar2020-03-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit) RAM: 1GB or 2GB RAM DDR3L @ 672Mhz Flash: 0/4/16GB eMMC flash memory for storage and boot MicroSD card connector for cards up to 32GB Debug: serial UART debug header with 0.1" pins Wired connectivity: 10/100/1000Mbps GbE Ethernet Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and Bluetooth 4.0 module with built-in antenna (only available in the A64-OLinuXino-1G4GW) Flashing instructions: Standard sunxi SD card installation procedure - copy eMMC image to SD card, insert in into SD card slot on the device and boot. You should see something like following if the eMMC is detected correctly: mmcblk2: mmc2:0001 P1XXXX 3.60 GiB mmcblk2boot0: mmc2:0001 P1XXXX partition 1 16.0 MiB mmcblk2boot1: mmc2:0001 P1XXXX partition 2 16.0 MiB Then flash SD card eMMC image straight into the mmcblk2 device: dd if=/mnt/openwrt...a64-olinuxino-emmc-squashfs-sdcard.img of=/dev/mmcblk2 It also possible to boot from boot0 partition[1]: 1. Compile U-Boot with CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x40 otherwise the U-Boot will get stuck in bootloop 2. Configure eMMC to boot from boot0 partition inside U-Boot: mmc bootbus 1 1 0 0; mmc partconf 1 1 1 0 3. echo 0 > /sys/block/mmcblk2boot0/force_ro 4. Write U-Boot from offset 0 (not offset 8k as with SD card) into boot0 partition dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2boot0 Known issues: Wireless doesn't work properly via netifd. 1. https://linux-sunxi.org/index.php?title=Bootable_eMMC Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: a53: add support for Olimex A64-OlinuxinoPetr Štetiar2020-03-28
| | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit) RAM: 1GB or 2GB RAM DDR3L @ 672Mhz Flash: 0/4/16GB eMMC flash memory for storage and boot MicroSD card connector for cards up to 32GB Debug: serial UART debug header with 0.1" pins Wired connectivity: 10/100/1000Mbps GbE Ethernet Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and Bluetooth 4.0 module with built-in antenna (only available in the A64-OLinuXino-1G4GW) Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert in into SD card slot on the device and boot. Known issues: Wireless doesn't work properly via netifd. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: a53: image: make it DRYPetr Štetiar2020-03-28
| | | | | | Replace same copy&pasted lines with the appropriate reusable bits. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: tidy up and sort alphabetically in image MakefilesAdrian Schmutzler2020-01-23
| | | | | | | | | | This tidies up the image Makefiles for the sunxi target by: - Move the if-condition for the subtarget to the parent Makefile - Remove lots of unnecessary empty lines - Sort device definitions alphabetically - Harmonize line wrapping for DEVICE_PACKAGES Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: rename SUNXI_SOC to SOCAdrian Schmutzler2019-12-20
| | | | | | | This replaces SUNXI_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: construct DTS name from device node name and SOCAdrian Schmutzler2019-12-13
| | | | | | | | | The device part in the SUNXI_DTS variable always corresponds to device node name. This is another redundancy that can be removed by calculating the DTS name from a newly introduced SUNXI_SOC variable and the node name. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: use vendor_device scheme for device definitionsAdrian Schmutzler2019-12-13
| | | | | | | | | | | | This changes device definition to resemble the vendor_device scheme already present for the majority of device compatible strings. By doing this, we achieve several advantages at once: - Image names and node names are more consistent with other targets. - SUPPORTED_DEVICES can be set automatically for all but two cases. - Image names and node names are in line with DEVICE_TITLEs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: convert to multi-variable device titleLuis Araneda2019-07-10
| | | | | | | Use data from the linux-sunxi community wiki to fill-in missing device information Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* sunxi: build image/uboot for the NanoPi NEO2Jasper Scholte2018-09-22
| | | | | | | | The NanoPi NEO2 is a small Allwinner H5 based board available with different DRAM configurations. This board is very similar to the NanoPi NEO PLUS2 Signed-off-by: Jasper Scholte <NightNL@outlook.com>
* sunxi: Added support for Xunlong Orange Pi PC2Antonio Silverio2018-08-09
| | | | | | | | | | | | | | | | CPU: H5 High Performance Quad-core 64-bit Cortex-A53 GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL Memory: 1GB DDR3 (shared with GPU) Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB) Onboard Network: 1000M/100M Ethernet RJ45 USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode role by default in DTS Buttons: Power Button(SW4) Debug TTL UART: ..DC-IN.. >[GND][RX][TX] ..HDMI.. Signed-off-by: Antonio Silverio <menion@gmail.com>
* sunxi: add build for sopineFan Fan2018-03-23
| | | | | | This will generate image for Pine64 Sopine board. Signed-off-by: Fan Fan <fkpwolf@gmail.com>
* sunxi: Add Xunlong Orange Pi Zero PlusHauke Mehrtens2018-02-17
| | | | | | | This is based on a patch from armbian: https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: add support for NanoPi NEO Plus2 boardAntony Antony2018-02-17
| | | | | | | | | | | | | | arm64: allwinner: h5: NanoPi NEO Plus2 DT support Add initial DT for NanoPi NEO Plus2 by FriendlyARM - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU - 1 GB DDR3 RAM - 8GB eMMC flash (Samsung KLM8G1WEPD-B031) - micro SD card slot - Gigabit Ethernet (external RTL8211E-VB-CG chip) - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module) - 2x USB 2.0 host ports & 2x USB via headers Signed-off-by: Antony Antony <antony@phenome.org>
* sunxi: Add A64 support with cortex53 subtargetHauke Mehrtens2017-09-18
This adds initial support for the A64 Allwinner SoC to LEDE. It will be build in the new cortexa53 subtarget. Currently it only supports the pine64 and the image is able to boot on this SoC. Camera, Ethernet, HDMI and other parts are currently not working. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Powered by cgit, Themed by Ted Yin.