aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAge
...
* mac80211: rt2x00: experimental improvements for MT7620 wifiDaniel Golle2022-09-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Serge Vasilugin reports: To improve mt7620 built-in wifi performance some changes: 1. Correct BW20/BW40 switching (see comments with mark (1)) 2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531 3. Set bbp66 for all chains. 4. US_CYC_CNT init based on Programming guide, default value was 33 (pci), set chipset bus clock with fallback to cpu clock/3. 5. Don't overwrite default values for mt7620. 6. Correct some typos. 7. Add support for external LNA: a) RF and BBP regs never be corrected for this mode b) eLNA is driven the same way as ePA with mt7620's pin PA but vendor driver explicitly pin PA to gpio mode (for forrect calibration?) so I'm not sure that request for pa_pin in dts-file will be enough First 5 changes (really 2) improve performance for boards w/o eLNA/ePA. Changes 7 add support for eLNA Configuration w/o eLAN/ePA and with eLNA show results tx/rx (from router point of view) for each stream: 35-40/30-35 Mbps for HT20 65-70/60-65 Mbps for HT40 Yes. Max results for 2T2R client is 140-145/135-140 with peaks 160/150, It correspond to mediatek driver results. Boards with ePA untested. Reported-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for ZyXEL Keenetic 4G Rev.B DeviceSergei Burakov2022-09-13
| | | | | | | | | | | | | | | | | | | | | | | | Specification: SoC: RT5350 CPU Frequency: 360 MHz Flash Chip: Macronix MX25L6406E (8192 KiB) RAM: Winbond W9825G6JH-6 (32768 KiB) 3x 10/100 Mbps Ethernet (2x LAN, 1x WAN) 1x external antenna UART (J1) header on PCB (57800 8n1) Wireless: SoC-intergated: 2.4GHz 802.11bgn USB: Yes 8x LED, 2x button Flash instruction: Configure PC with static IP 192.168.99.8/24 and start TFTP server. Rename "openwrt-ramips-rt305x-zyxel_keenetic-4g-b-squashfs-sysupgrade.bin" to "rt305x_firmware.bin" and place it in TFTP server directory. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Sergei Burakov <senior.anonymous@mail.ru>
* ramips: disable unsupported background radar detectionShiji Yang2022-09-12
| | | | | | | | | | | | | | | | | | | Background radar detection is not supported on devices that using MT7905, so disable this feature in the following devices: asus,rt-ax53u jcg,q20 tplink,eap615-wall-v1 xiaomi,mi-router-cr6606 xiaomi,mi-router-cr6608 xiaomi,mi-router-cr6609 yuncore,ax820 Devices with MT7915 lacking a DFS antenna also do not support background DFS: totolink,x5000r cudy,x6 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Ubiquiti UniFi FlexHDSven Wegener2022-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- - SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash - Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4) - Bluetooth: CSR8811 (internal USB, install kmod-bluetooth) Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Update the bootloader environment. $ fw_setenv devmode TRUE $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 3. Transfer the OpenWrt sysupgrade image to the device using SCP. 4. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 5. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 7. Reboot the device. It should boot into OpenWrt. Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
* ramips: ASUS RT-ACx5P phy[01]radio to phy[01]tptDavid Santamaría Rogado2022-09-11
| | | | | | | | phy[01]radio leaves the leds always on, if they are set through sysfs the leds get off. Set the triggers to phy[01]tpt to make them work. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* ramips: add support for Linksys E7350Rosen Penev2022-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for Belkin RT1800Rosen Penev2022-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for Kroks Rt-Cse SIM Injector DSAndrey Butirsky2022-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958: https://kroks.ru/search/?text=1958 See Kroks OpenWrt fork for support of other models: https://github.com/kroks-free/openwrt Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 5x 10/100 Mbps - 2.4 GHz: b/g/n SoC - USB: 1x - SIM-reader: 2x (driven by a dedicated chip with it's own firmware) - Buttons: reset - LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.) Flashing: - sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254 - U-Boot launches a WEB server if Reset button is held during power up, IP: 192.168.1.1 MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* ramips: add support for Kroks Rt-Pot mXw DS RSIM routerAndrey Butirsky2022-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka "Kroks KNdRt31R19". Ported from v19.07.8 of OpenWrt fork: see https://github.com/kroks-free/openwrt for support of other models. Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - mPCIe: 1x (usually equipped with an LTE modem by vendor) - Buttons: reset - LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status Flashing: - sysupgrade image via stock firmware WEB interface. - U-Boot launches a WEB server if Reset button is held during power up. Server IP: 192.168.1.1 SIM card switching: The device supports up to 4 SIM cards - 2 locally on board and 2 on remote SIM-injector. By default, 1-st local SIM is active. To switch to e.g. 1-st remote SIM: echo 0 > /sys/class/gpio/modem1power/value echo 0 > /sys/class/gpio/modem1sim1/value echo 1 > /sys/class/gpio/modem1rsim1/value echo 1 > /sys/class/gpio/modem1power/value MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Kroks <dev@kroks.ru> [butirsky@gmail.com: port to master; drop dts-v1] Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* ramips: define Yuncore AX820 switch LEDsThibaut VARÈNE2022-08-29
| | | | | | | | | This patch defines the two switch LED to bring them under user control. Fixes: a0e1d3ab7b4f ("ramips: improve YunCore AX820 LEDs") Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> [rmilecki: leave "label"s in place] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: mt7621-dts: mux phy0/4 to gmac1Arınç ÜNAL2022-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2 pins are available. This achieves 2 Gbps total bandwidth to the CPU using the second RGMII. The ports called "wan" are muxed where possible. On a minority of devices, this is not possible. Those cases: mt7621_ampedwireless_ally-r1900k.dts: lan3 mt7621_ubnt_edgerouter-x.dts: eth0 mt7621_gnubee_gb-pc1.dts: ethblue mt7621_linksys_re6500.dts: lan1 mt7621_netgear_wac104.dts: lan4 mt7621_tplink_eap235-wall-v1.dts: lan0 mt7621_tplink_eap615-wall-v1.dts: lan0 mt7621_ubnt_usw-flex.dts: lan1 The "wan" port is just what the vendor designated on the board/plastic chasis of the device. On a technical level, there is no difference between a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer connecting to WAN via the port described above for these devices to benefit the feature brought with this patch. mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks like it should, because the rgmii2 pins are wired to unused components. Tested on a range of devices documented on the GitHub PR. Link: https://github.com/openwrt/openwrt/pull/10238 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621-dts: remove DTS_LEGACY from ethernet nodeArınç ÜNAL2022-08-20
| | | | | | | | | Remove DTS_LEGACY put for claiming pin groups for the ethernet node from the ethernet node. It's not an old kernel trait. These bindings need to be there on the newer kernels as well. Fixes: a3764ee29dd0 ("ramips: add linux 5.15 support for mt7621") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: mt7621-dts: do not claim rgmii2 group as gpio for certain devicesArınç ÜNAL2022-08-20
| | | | | | | | | | | | | | | These devices do not use rgmii2 as gpio, therefore remove rgmii2 pin group from state-default. Remove overwriting the ethernet node for these devices. Move claiming the rgmii2 group from mt7621_zyxel_nwa-ax.dtsi to mt7621_zyxel_nwa50ax.dts as it's only the latter using rgmii2 pins as gpio. Remove duplicate ethernet overwrite from mt7621_tplink_archer-x6-v3.dtsi. Claim rgmii2 group as gpio on mt7621_bolt_arion.dts as it uses an rgmii2 pin, 26, as gpio. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: fix GB-PC1 and GB-PC2 device supportArınç ÜNAL2022-08-20
| | | | | | | | | | | | | | | | Change switch port labels to ethblack & ethblue. Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins. Add the external phy with ethyellow label on the GB-PC2 devicetree. Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function. Enable ICPlus PHY driver for IP1001 which GB-PC2 has got. Update interface name and change netdev function. Enable lzma compression to make up for the increased size of the kernel. Make spi flash bindings on par with mainline Linux to fix read errors. Tested on GB-PC2 by Petr. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: fix ZyXEL NWA55AXE model nameDavid Bauer2022-08-18
| | | | | | The model name was missing a letter. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Beeline SmartBox TURBOMikhail Zhilkin2022-08-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 Button: 2 buttons (Reset & WPS) LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (admin:admin) 2. Navigate to Settings -> WAN -> Add static IP interface (e.g. 10.0.0.1/255.255.255.0) 3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before 4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router 5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where SNxxxxxxxxxx is the serial number from the backplate label) 6. Run in SSH shell: sh 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface (admin:admin) 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- 1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 10.0.0.2 MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:54 | | WAN | label + 1 | *:55 | | 2g | label + 4 | *:58 | | 5g | label + 5 | *:59 | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Co-developed-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add support for ZyXEL LTE3301-PlusAndré Valentin2022-08-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7615E - Switch: 4 LAN ports (Gigabit) - LTE: Quectel EG506 connected by USB3 to SoC - SIM: 1 micro-SIM slot - USB: USB3 port - Buttons: Reset, WPS - LEDs: Multicolour power, internet, LTE, signal, Wifi, USB - Power: 12V, 1.5A The device is built as an indoor ethernet to LTE bridge or router with Wifi. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc MAC assignment: lan: 98:0d:67:ee:85:54 (base, on the device back) wlan: 98:0d:67:ee:85:55 Installation from web GUI: - Log in as "admin" on http://192.168.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - format ubi device: ubiformat /dev/mtd6 - attach ubi device: ubiattach -m6 - create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB - rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB - run sysupgrade with sysupgrade image For more details about flashing see commit 2449a632084b ("ramips: mt7621: Add support for ZyXEL NR7101"). Please note that this commit is needed: firmware-utils: add marcant changes for ZyXEL NBG6716 and LTE3301-PLUS Signed-off-by: André Valentin <avalentin@marcant.net>
* ramips: mt7628: fix memory controller reset bitReto Schneider2022-08-06
| | | | | | | | | | | According to MediaTek MT7688 Datasheet v1.4, as well as the MT7628 counterpart, the memory controller reset bit (MC_RST) is 10, not 20. Reset bit 20 is used for for UART 2 (UART2_RST). Please note: Due to the lack of hardware, I was not able to test this change. Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
* ramips: add support for Netcore NW5212David Yang2022-08-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netcore NW5212, provided by some carrier in China. Specifications: -------------- * SoC: Mediatek MT7620A * RAM: 128MB DDR2 * Flash: 16MB SPI NOR flash (Winbond W25Q128BV) * WiFi 2.4GHz: builtin * Ethernet: builtin * LED: Power, WAN, LAN 1-4, WiFi * Buttons: Reset (GPIO 13) * UART: Serial console (57600 8n1) * USB: 1 x USB2 Installation: ------------ The router comes with OpenWrt 14.07 built with MTK SDK. However, as the modem is provided by carriers, so the web interface is highly minimized and only contains a static page with no interaction options. There are two possible ways to gain the access. 1) Open the shell and use a UART2USB convert to gain TTY access. Please notice you have to remove resistance R54 at the back of the board otherwise you won't be able to input anything. 2) Use built-in backdoor. Access http://192.168.1.1/cgi-bin/_/testxst to start dropbear service at port 9122. Be warned the software is super old and only diffie-hellman-group1-sha1, diffie-hellman-group14-sha1, kexguess2@matt.ucc.asn.au is support, you may not be able to connect it with an up-to-date ssh client. After you can control the device, flash the firmware as usual. Here are some hints for that. Option 1 (via original firmware): 1) Setup HTTP server on your computer, for example: python3 -m http.server 2) Connect to the route and flash: cd /tmp wget http://<your-computer-host>/<your-firmware-name> mtd -r write <your-firmware-name> firmware Option 2 (replacing u-boot via breed): 1) Download breed-mt7620-reset13.bin from https://breed.hackpascal.net/ 2) Setup HTTP server on your computer, for example: python3 -m http.server You can skip this step if your breed is already accessible from HTTP, since the original wget does not support HTTPS. 3) Connect to the route and flash breed: cd /tmp wget http://<your-computer-host>/breed-mt7620-reset13.bin mtd write breed-mt7620-reset13.bin Bootloader 4) Reboot. Hold reset key or press any key in TTY to enter breed. 5) Access breed web interface (http://192.168.1.1/). Choose the flash layout to be 0x50000 and flash new firmware. MAC addresses: ------------- There are three MACs stored in factory, as in MT7620A reference design: source address usage 0x4 label WLAN 0x28 label MAC 1 0x2e label + 1 MAC 2 However, the OEM firmware only uses one single MAC (label) for all interfaces, probably a misconfiguration. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: add support for Netgear PR2000David Yang2022-08-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netgear PR2000, sold as "Travel Router and Range Extender". Specifications: -------------- * SoC: Mediatek MT7620N * RAM: 64MB DDR2 * Flash: 16MB SPI NOR flash (Macronix MX25L12805D) * WiFi 2.4GHz: builtin * Ethernet: builtin * LED: Power, Internet, WiFi, USB * Buttons: Reset (GPIO 1/2) * UART: Serial console (57600 8n1) * USB: 1 x USB2 SPECIAL NOTES: ------------- Problem: WiFi is super weak, but SSID beacons seems to be right. Solve: Change 36h in factory partition (namely 0xf60036) to be 0x0. Explain: Clearly Netgear have different ideas on how EEPROM is used. Bit 2 of 36h indicates the presence of External LNA for 11g (2.4 GHz) band, which seems to be incorrectly set by Netgear (originally 0x04). Lifting it solves the problem of weak RX signal. Installation: ------------ There are two possible ways to install the firmware. Flashing via web interface of original firmware is not tested due to a broken firmware. 1) Open the shell and use a UART2USB convert to gain TTY access (TP7: RXD, TP9: TXD, TP10: GND). Please notice you have to remove resistance R54 next to TP7 otherwise you won't be able to input anything. 2) Use well-known Netgear debug switch. Access http://192.168.168.1/setup.cgi?todo=debug to start telnet service (username: root, password: <none>). Please back up firmware if you want to go back to the original. After you can control the device, flash the firmware as usual. Here are some hints for that. Option 1 (via nmrpflash): 1) Download nmrpflash from https://github.com/jclehner/nmrpflash 2) Use *-factory.img and flash: nmrpflash -L nmrpflash -i net* -f <your-firmware-name> 3) Turn off then turn on the device, wait it finishing flash. Option 2 (replacing u-boot via breed): 1) Download breed-mt7620-reset1.bin from https://breed.hackpascal.net/ 2) Setup HTTP server on your computer, for example: python3 -m http.server You can skip this step if your breed is already accessible from HTTP, since the original wget does not support HTTPS. 3) Connect to the route and flash breed: cd /tmp wget http://<your-computer-host>/breed-mt7620-reset1.bin dd if=breed-mt7620-reset1.bin of=/dev/mtdblock0 bs=64k 4) Reboot. Hold reset key or press any key in TTY to enter breed. 5) Access breed web interface (http://192.168.1.1/). Choose memory layout to be 0x40000 and flash new firmware. Remark: ------ As a "Range Extender", it has a switch to switch between Wired mode (GPIO 21 low) and Wireless mode (GPIO 20 low), which is not implemented in this patch. However, the router will be turned off when it switches to the middle, which makes this switch much less useful. MAC addresses: ------------- The OEM firmware uses one single MAC for all interfaces, located at 0xf700b0. Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: adding support for Asus RP-AC56Lea Teuberth2022-08-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: CPU: MT7621A dual-core 880MHz RAM: 64MB DDR2 FLASH: 16MB MX25L12805D NOR SPI WIFI: 2.4GHz 2x2 MT7603 b/g/n PCI WIFI: 5GHz 2x2 MT7662 a/b/ac PCI ETH: 1xLAN 1000base-T integrated SWITCH: MT7530 Port 0: LAN, Port 6: CPU LED: Power, 2.4GHz WiFi, 5GHz WiFi BTN: WPS, Reset UART: Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1 MISC: Audio support Installation: 1. Update using recovery mode - while holdig "reset" button, power on the device - keep holding "reset" until power led is flashing yellow - set own IP to 192.168.1.75, subnet mask: 255.255.255.0 - push firmware image (can be factory.bin or sysupgrade.bin) using tftp client in binary mode to 192.168.1.1 Notes: This board has only two MAC addresses programmed in the "factory" partition: - MAC for wlan0 (2.4GHz) at offset 0x0004 - MAC for wlan1 (5GHz) at offset 0x8004 - stock firmware re-uses wlan0 MAC for ethernet - no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006 Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
* ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806Shiji Yang2022-07-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | H3C TX180x series WiFi6 routers are customized by different carrier. While these three devices look different, they use the same motherboard inside. Another minor difference comes from the model name definition in the u-boot environment variable. Specifications: SOC: MT7621 + MT7915 ROM: 128 MiB RAM: 256 MiB LED: status *2 Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP server IP: 192.168.124.99 MAC Address: use address(sample 1) address(sample 2) source label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1 wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode) WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode) WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7 WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7 Compatibility mode is used to guarantee the connection of old devices that only support WiFi4 or WiFi5. TFTP + TTL Installation: Although a TTL connection is required for installation, we do not need to tear down it. We can find the TTL port from the cooling hole at the bottom. It is located below LAN3 and the pins are defined as follows: |LAN1|LAN2|LAN3|----|WAN| -------------------- |GND|TX|RX|VCC| 1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in server's root directory, rename it to a simple name "initramfs.bin". 2. Plug in the power supply and wait for power on, connect the TTL cable and open a TTL session, enter "reboot", then enter "Y" to confirm. Finally push "0" to interruput boot while booting. 3. Execute command to install a initramfs system: # tftp 0x80010000 192.168.124.99:initramfs.bin # bootm 0x80010000 4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those partitions if we want to back to stock firmwre due to official website does not provide download link. # dd if=/dev/mtd1 of=/tmp/u-boot-env.bin # dd if=/dev/mtd4 of=/tmp/firmware.bin 5. Edit u-boot env to ensure use default bootargs and first image slot: # fw_setenv bootargs # fw_setenv bootflag 0 6. Upgrade sysupgrade firmware. 7. About restore stock firmware: flash the "firmware" and "u-boot-env" partitions that we backed up in step 4. # mtd write /tmp/u-boot-env.bin u-boot-env # mtd write /tmp/firmware.bin firmware Additional Info: The H3C stock firmware has a 160-byte firmware header that appears to use a non-standard CRC32 verification algorithm. For this part of the data, the u-boot does not check it so we can just directly replace it with a placeholder. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for ZyXEL NWA50AX / NWA55AXEDavid Bauer2022-07-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Netgear WAX202Wenli Looi2022-07-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX202 is an 802.11ax (Wi-Fi 6) router. Specifications: * SoC: MT7621A * RAM: 512 MiB NT5CC256M16ER-EK * Flash: NAND 128 MiB F59L1G81MB-25T * Wi-Fi: * MT7915D: 2.4/5 GHz (DBDC) * Ethernet: 4x 1GbE * Switch: SoC built-in * USB: None * UART: 115200 baud (labeled on board) Load addresses (same as ipTIME AX2004M): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * Note that the bootloader accepts both encrypted and unencrypted images, while the stock web interface only accepts encrypted ones. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in WAX202 GPL source: https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ramips: Add Xiaomi Mi Router 4A 100M InternationalNita Vesa2022-07-03
| | | | | | | | | | | | The international version of Mi Router 4A 100M is physically identical to the non-international one, but appears to be using a different partitioning scheme with the "overlay" partition being 2MiB in size instead of 1MiB. This means the following "firmware" partition starts at a different address and the DTS needs to be adjusted for the firmware to work. Signed-off-by: Nita Vesa <werecatf@outlook.com>
* ramips: Add suport for COMFAST CF-WR617ACSergei Iudin2022-07-03
| | | | | | | | | | | | | | | | | Specifications: Chipset:MT7628DA+MT7612E Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps Output Power :100mW(20dbm) Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port Flash: 8Mb DRam: 64Mb Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1 Known issues: mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition. Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
* ramips: add support for Beeline SmartBox GIGAMikhail Zhilkin2022-07-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: improve YunCore AX820 LEDsThibaut VARÈNE2022-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At least two AX820 hardware variants are known to exist, but they cannot be distinguished (same hardware revision, no specific markings). They appear to have the same LED hardware, but wired differently: - One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and a blue wlan5g LED at GPIO 16; - The other only offers a green system LED at GPIO 15, with GPIO 14 and 16 being apparently not connected Finally, a Yuncore datasheet says the canonical wiring should be: - Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16 All GPIOs are tied to a single RGB LED which is exposed via lightpipe on the device front casing. Considering the above, this patch exposes all three LEDs, preserves the common system LED (GPIO 15) as the openwrt status LED, and removes the color information from the LEDs names since it is not consistent across hardware. The LED naming is made consistent with other YunCore devices. A note is added in DTS to ensure this information is always available and prevent unwanted changes in the future. Fixes: #10131 "YunCore AX820: GPIO LED not correct" Reviewed-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: add support for ASUS RP-AC87Tamas Balogh2022-06-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC87 ac2600 Repeater 2.4GHz 800Mbps 5GHz 1733Mbps Hardware specifications: SoC: MT7621A 2 cores 4 threads @880MHz WiFi2G: MT7615E 2G 4x4 b/g/n Wifi5G: MT7615E 5G 4x4 n/ac DRAM: 128MB DDR3 @1200mhz Flash: 16MB MX25L12805D SPI-NOR LAN/WAN: MT7530 1x1000M MAC addresses as verified by OEM firmware: use address source Lan/W5G *:B0 factory 0x8004 (label) W2G *:B4 factory 0x0 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.2 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFPArınç ÜNAL2022-06-24
| | | | | | | | | | | | | | | | | | | For a TX->TX connected external phy to transmit/receive data, the rgmii2 pin group needs to be claimed with gpio function, at least for EdgeRouter X SFP. We already claim the pin group under the pinctrl node with gpio function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi. However, we should claim a pin group under its consumer node. It's the ethernet node in this case, which we already claim the rgmii2 pin group under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2 node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group under the pinctrl node. With this change, we also get to remove a definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to EdgeRouter X SFP. This change is tested on an EdgeRouter X SFP. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-18
| | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-06-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: create new dtsi for Arcadyan routersMikhail Zhilkin2022-06-13
| | | | | | | | | | | | | | | | | | | This commit moves common properties for the boards below to a new dtsi: Beeline Smartbox Flash (Arcadyan WG443223) MTS WG430223 (Arcadyan WG430223) The boards are almost the same. Here is the differences: +------+----------+----------+ | | WG430223 | WG443223 | +------+----------+----------+ | RAM | 128 | 256 | +------+----------+----------+ | USB | - | 1x3.0 | +------+----------+----------+ | LEDS | RG | RGB | +------+----------+----------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: decrease SPI frequency for Phicomm K2PAviana Cruz2022-06-13
| | | | | | | | | | Some K2P comes with the worse boards with GD25Q128 (may be A2), which only works with 50MHz frequency and less. Reduce spi frequency so that these routers can boot. remove m25p,fast-read because it isn't needed for 50MHz SPI. Signed-off-by: Aviana Cruz <gwencroft@proton.me> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: use hotplug script for EAP615-Wall MACsStijn Tintel2022-06-03
| | | | | | | | | | | | | Using nvmem-cells to set the MAC address for a DBDC device results in both PHY devices using the same MAC address. This in turn will result in multiple BSSes using the same BSSID, which can cause various problems. Use the hotplug script for the EAP615-Wall instead to avoid this. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
* ramips: disable unsupported background-radarDavid Bauer2022-05-29
| | | | | | | | The UniFi 6 Lite as well as the Tenbay T-MB5EU do not have the third background-radar chain. For the Tenbay, the connector is present, however no antenna is connected to it. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add led_source for Asus RT-AC1200 devicesTamas Balogh2022-05-15
| | | | | | | | | | | | | | | this adds the mediatek,led_source dts binding for Asus RT-AC1200 devices' dtsi, for correct switch LED behavior. The dts-binding is introduced in commit: 65dc9e0980255b15402c45b840f239b85be59b3d Without this, we only have constantly very fast blinking LEDs, which don't react on any traffic or LAN events at all. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ramips: add support for Cudy X6Alessio Prescenzo2022-05-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7621 RAM: 256 MB Flash: 32 MB WiFi: MediaTek MT7915E Switch: 1 WAN, 4 LAN (Gigabit) Ports: 1 USB 3.0 Buttons: Reset, WPS LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB Power: DC 12V 1A tip positive Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: Loads only signed manufacture firmware due to bootloader RSA verification serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 connect to any lan ethernet port power on the device while holding the reset button wait at least 8 seconds before releasing reset button for image to download Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com> [ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add i2c in dts for GL-MT300N-V2Ptilopsis Leucotis2022-05-05
| | | | | | | | According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/ GL-MT300N-V2 have I2C interface on GPIO4, GPIO5. Adding I2C in device tree make possible using I2C on this device. Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
* ramips: zbt-wg2626: Fix the LAN ports namesAlban Bedel2022-05-01
| | | | | | | The current names don't match with the labels on the case, reverse the LAN ports order so they match. Signed-off-by: Alban Bedel <albeu@free.fr>
* ramips: zbt-wg2626: Add the reset gpio for PCIe port 1Alban Bedel2022-05-01
| | | | | | | | | | | | | The 2.4GHz interface doesn't come up properly with the log showing: mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) As seen on other MT7621 boards this is caused by a missing reset GPIO. The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO list to also reset the 2.4GHz interface on port 1. Signed-off-by: Alban Bedel <albeu@free.fr>
* ramips: add support for Wavlink WL-WN533A8Davide Fioravanti2022-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports and one USB 3.0 port. It's also known as Wavlink QUANTUM T8. Hardware -------- SoC: Mediatek MT7621A RAM: 128MB (Nanya NT5CB64M16GP-EK) FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3) ETH: - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC - 1x MT7615NE (4x4:4) 5GHz - 8 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 3.0 port UART: - 57600-8-N-1 J4 Everything works correctly. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. (Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204) Restore OEM Firmware -------------------- Flash the firmware update available online directly from LUCI. You can download it from: https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006) WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000) WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:65 In OEM firmware the DBDC wifi interfaces have these mac addresses: 2G) 82:XX:XX:XX:XX:65 5G) 80:XX:XX:XX:XX:65 While in OpenWrt the addresses are: 2G) 80:XX:XX:XX:XX:65 5G) 02:XX:XX:XX:XX:65 2) radio0 will show as 2G/5G interface but only 2G is really usable. 3) There is just one wifi led for all wifi interfaces. It currently shows only the radio0 GHz wifi activity. 4) My unit was shipped with M33A8.V5030.190716 firmware which contains the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in the input box it will start the telnet daemon. Now you can access the telnet console on port 2323 with these credentials: username: admin2860 password: admin 5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the webcmd.shtml page. If your router is shipped with a previous firmware version and you want to back it up, you can follow the back up procedure of the WS-WN583A6. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: create shared DTSI for Wavlink WN53XAX devicesDavide Fioravanti2022-04-30
| | | | | | | Most of the definitions for WN531A6 will be shared with WN533A8 in a future commit, so put them in a shared DTSI. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for TP-Link RE650 v2Marcin Gordziejewski2022-04-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v2 is largely similar to v1 that is already supported by OpenWrt. Notable differences is differnt SPI Flash - 8 MB instead of 16 MB (from cFeon instead of Winbond) and a different configuration of PCIE connections to wifi chips. Otherwise it's largely the same product as v1 Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 8 MB - cFeon QH64A-104HIP - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART pinout - GND, RX, TX, labeled in the middle of the PCB, requires soldering because they're not through holes. Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: I didn't try recovering back to the stock firmware, however, if there is such process for other RExxx devices, it seems like it could be similar here. Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
* ramips: add support for YunCore AX820/HWAP-AX820Clemens Hopfer2022-04-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
* ramips: add support for OrayBox X3ARay Wang2022-04-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: mt7621: make u_env partition r/w for Linksys EA7xxx devicesRussell Morris2022-04-16
| | | | | | | | Make u_env partition read/write - currently cannot write to it, which blocks fw_setenv. This in turn breaks features like Advanced Reboot, which rely on setting the environment variable boot_part (1 or 2). Signed-off-by: Russell Morris <rmorris@rkmorris.us>
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
Powered by cgit, Themed by Ted Yin.