| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There was no config in the uboot-envtools package, so there is no
generated /etc/fw_env.config for the fw_printenv and fw_setenv utils.
Since uboot-envtools 2024.01, there is a way to make these utils work
without /etc/fw_env.config if the DT has an env partition with the prop.:
compatible = "u-boot,env";
So, this commit adds the prop. above to the appsblenv:0 partition
in the yuncore ax880 DTS file.
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15305
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
| |
|
|
|
|
|
|
|
| |
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
| |
The qca8081 phy needs to set the reset delay time,
otherwise it will not be detected by the mdio bus.
Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
| |
|
|
|
|
|
|
| |
Switch to qca8081 upstream PHY. Update every device that have LEDs
attached to the qca8081 PHY to follow new way of defining the LEDs and
add original OEM configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Fix multiple error on ESS switch port define.
- Fix wrong switch CPU and WAN bmp define. (many times wan port are
actually set in lan mask and lan port in wan mask)
- Renumber phyinfo port, use port_id instead of phy_address as it
doesn't make sense using that for port enumeration
- Drop additional port for devices that have them not connected.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
| |
Every board in qualcommax is using the same BM and TM switch tick modes, so
instead of specifying them in each board lets just set them in the ESS DTSI
directly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
| |
|
|
|
|
|
|
|
|
| |
Now that we have the MAC modes defined in DT bindings, lets replace all of
the raw hex values with defines.
While we are here, we can drop the disabled UNIPHY-s as that is the default
value in the ESS DTSI.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
switch_lan_bmp and switch_wan_bmp have wrong values and now cause
problems with the new version of the qca-ssdk.
Fix the wrong entry and drop the redundant switch_cpu_bmp.
Also introduce some convenient define to better understand values in
this map.
Fixes: eea264feadcf ("kernel: qca-ssdk: update to 12.4")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Dynalink AX3600 and Qnap 301W
Reviewed by: Robert Marko <robimarko@gmail.com>
|
|
|
SPECIFICATION:
- Chipset: IPQ8072A +QCN5054+QCN5024+QCA8081*2
- Flash NOR-8MB AND NAND-128MB
- RAM 1Gb DDR
- IEEE 802.11: 802.11ax/ac/b/g/n
- 4*4 2.4G Wi-Fi standard 802.11b/g/n/ax
- 4*4 5.8G Wi-Fi Standard 802.11 a/n/ac/ax
- 2x 1 Gbps Ethernet (QCA8081) with 802.3at PoE input support
- 1x Reset
- 1x Bluetooth(optional)
- 1x DC Port 12V 3A
- 4x Antenna IPEX Connector, 3dBi omni antennas
- Data Rate: 3657Mbps ( 2.4G: 1182Mbps (11ax 4x4); 5.8G: 2475Mbps (11ax 4x4))
- RF Power: 2.4g ≤ 20dBm; 5.8g ≤ 19dBm
- LED light: Sys; 5.8G wifi; 2.4G wifi; WAN; LAN
- Max Power Consumption: ≤ 22W
- Size: 198mm * 198mm * 41.02mm
BACKUP YOUR STOCK FIRMWARE:
```
export device=ax880
mkdir -p /tmp/fw_dump_$device
cd /tmp/fw_dump_$device
dmesg > dmesg_$device.log
dtc -I fs /sys/firmware/devicetree/base > $device.dts
cat /proc/device-tree/model > model
cat /proc/mtd > proc_mtd
while read p; do
mtd_dev=$(echo $p | cut -d: -f1)
echo $mtd_dev
dd if=/dev/$mtd_dev of=$mtd_dev
done < proc_mtd
md5sum * > md5sum.log
tar -cvzf ../$device.tar.gz .
export sum=$(md5sum /tmp/$device.tar.gz | cut -d' ' -f1)
mv ../$device.tar.gz /tmp/${device}_${sum}.tar.gz
echo fw backup saved to: /tmp/${device}_${sum}.tar.gz
```
Upload your backup via tftp to the safe place.
INSTALLATION:
1. stock firmware web ui
Rename factory.bin fw image file to factory.ubin. Flash this image
like ordinary stock fw upgrade.
2. stock firmware telnet method
Enter telnet cli (login: root, password: 476t*_f0%g09y) and upload
factory.bin fw image and rename it to factory.ubin
`cd /tmp && wget <your_web_server_ip>/factory.ubin`
`sysupgrade factory.ubin
3. initramfs method
Put openwrt-ipq807x-generic-yuncore_ax880-initramfs-uImage.itb to your
TFTP server and rename it to ax880.initram
Enable serial console and enter to the u-boot cli.
Exec these commands:
`tftpboot <your_tftp_server_ip>:ax880.initram`
`dhcp`
When downloading is finished:
`bootm`
After booting the device, you need to upload to the device factory.ubi fw image.
```
cd /tmp && wget <your_web_server_ip>/factory.ubi`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f factory.ubi
ubiformat /dev/${rootfs_1} -y -f factory.ubi
reboot
```
4. u-boot factory.ubi image method
Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.ubi to your
TFTP server and rename it to ax880.ubi
Enter u-boot cli and exec these commands:
`tftpboot <your_tftp_server_ip>:ax880.ubi`
`dhcp`
After downloading is finished:
`flash rootfs`
`flash rootfs_1`
`reset`
5. u-boot factory.bin method
Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.bin to your
TFTP server and rename it to ax880.bin
Enter u-boot cli and exec these commands:
`tftpboot <your_tftp_server_ip>:ax880.bin`
`dhcp`
After downloading is finished:
`imgaddr=$fileaddr && nand device 0`
Erase rootfs memory:
`nand erase 0x00000000 0x03400000`
Write rootfs:
`nand write $fileaddr 0x00000000 $filesize`
Erase rootfs_1 memory:
`nand erase 0x3c00000 0x3400000`
Write rootfs_1
`nand write $fileaddr 0x3c00000 $filesize`
`reset`
STOCK FIRMWARE RECOVERY:
Boot initramfs image.
Upload your rootfs mtd partition to the device using scp or download
it from the device using wget.
Enter device ssh cli and exec:
```
cd /tmp && wget <your_web_server_ip>/mtd21`
export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
ubiformat /dev/${rootfs} -y -f /tmp/mtd21
ubiformat /dev/${rootfs_1} -y -f /tmp/mtd21
reboot
```
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
|