| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Device specification:
- MT7629 with 16MB NOR flash W25Q128 and 128 MB DDR3 RAM.
- MT7761N and MT7762N wireless chips (currenlty no driver in OpenWrt available)
- WiFi is NOT working on this device
- Dual core but second CPU doesn't seem to work (Error message during boot: "CPU1: failed to come online")
There are two similar merge requests for similar devices with the same issues:
- https://github.com/openwrt/openwrt/pull/12286
- https://github.com/openwrt/openwrt/pull/5084
UART interface is next to the reset button, pinout:
- 1: TX (the pin with the arrow marker)
- 2: RX
- 3: GND
- 4: VCC
UART settings: 115200,8n1, 3.3V
U-Boot menu can be entered by pressing Ctrl+B during startup.
Booting initramfs:
- Set your computers IP adress to 192.168.1.110
- Run a TFTP server providing the initramfs image
- Power on the AP, press Ctrl+B to get to the U-Boot menu
- Select "1. System Load Linux to SDRAM via TFTP"
- Update kernel file name, input server IP and input device IP (if they deviate from the defaults)
- After booting, create a backup of all partitions, especially for kernel and root_fs. They are required for reverting back to stock firmware
- The sysupgrade image can be flashed now
MAC adresses:
- LAN and 2.4GHz use the same MAC (the one printed on the device)
- 5GHz WiFi MAC is LAN MAC + 1
GPIOs:
- GPIO 21 is the reset pin (low active)
- GPIO 55 is for the green LED (active high)
- GPIO 56 is for the yellow/amber LED (active high)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
| |
1. fix typo: ucidef_set_interfaces_wan -> ucidef_set_interface_wan
2. change board name to mt7629-rfb to match upstream dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
base-files are added into subtarget directory like what's done
recently in ath79. For this subtarget, metadata checks are enforced
and a SUPPORTED_DEVICE is added to generate proper metadata.
Since we only have mt7629 support in 4.19, override KERNEL_PATCHVER
in target.mk for now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|