| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For all boards currently working with the mt7530 DSA driver we can
be sure that the address of the switch on the MDIO bus is 31 --
simply because that address is hard-coded in the driver and the
address from the Device Tree is being ignore.
An upcoming patch will add support for MT753x ICs which are programmed
to addresses different from 0x1f using bootstrap pins. As a result the
address from the Device Tree will then be taken into account, which
will break currently working boards which got the address set to
anything else than 31.
While at it also unify the syntax in Device Tree to always us a decimal
value for the 'reg' property.
* mt7622-buffalo-wsr-3200ax4s.dts
Cosmetic change 'reg = <0x1f>' -> 'reg = <31>'
* mt7622-dlink-eagle-pro-ai-ax3200-a1.dtsi
Wrong address: 0 -> 31
* mt7622-elecom-wrc-x3200gst3.dts
Wrong address: 0 -> 31
* mt7622-linksys-e8450.dtsi
Wrong address: 0 -> 31
* mt7622-ruijie-rg-ew3200.dtsi
Wrong address: 0 -> 31
* mt7622-xiaomi-redmi-router-ax6s.dts
Wrong address: 0 -> 31
* mt7629-iptime-a6004mx.dts
Wrong address: 2 -> 31
* mt7981b-zbtlink-zbt-z8102ax.dts
Cosmetic change 'reg = <0x1f>' -> 'reg = <31>'
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
|
|
| |
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
| |
mac-address-increment is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
| |
|
|
|
|
| |
Will allow removing mac-address-increment.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
| |
|
|
|
|
|
| |
This is not used by the DSA dt-binding, so remove it from all devicetrees.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
|
|
|
ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7622B.
Specifications:
- SoC : MediaTek MT7622B
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN : 2.4/5 GHz 4T4R
- 2.4 GHz : MediaTek MT7622B (SoC)
- 5 GHz : MediaTek MT7915A
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7531
- LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J19: 3.3V, GND, TX, RX from power jack side
- 115200n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-X3200GST3 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
MAC Addresses:
LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex))
WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex))
2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:7A (none)
Note:
- currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in
"trigger" file of LEDs, use "phy1radio" trigger instead
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|