| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for NXP LS1028ARDB reference board. It's a dual core
Coretex-A53 board with 4G RAM and 5 Eternet ports (4 ports are
connected to MSCC Felix switch).
The original layout of NXP board has been kept but firmware
images are adapted to be more sysupgrade friendly. At the moment
NOR and SD boots are supported.
NOR flash instructions:
* make sd card with sdboot image
* boot
* write firmware image to spi flash
$ mtd write /tmp/openwrt-layerscape-armv8_64b-fsl_ls1028a-rdb-
squashfs-firmware.bin /dev/mtd0
* change jumper to NOR boot and reset
V3:
* Added board specific network defaults for lan/wan
v2:
* Added INA220 curent monitor, PCF2129 RTC clock and NXP
SA56004ED temperature sensor to default packages
* removed compat fixups for thist board
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
|
| |
|
|
|
|
|
|
|
| |
commit 2c2d77bd3bd4 ("layerscape: add FRWY-LS1046A board support")
missed to add an entry to the 79_move_config preinit script.
Therefore, the config transfer on sysupgrade wass broken for this device.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
|
| |
|
|
|
|
|
| |
The compatible is a literal string without any problematic
characters, so there is no reason to quote it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
At this moment layerscape images are ext4 only. It causes problem with
save changes durring sysupgrade and make "firstboot" and failsafe mode
useless.
This patch changes sd-card images to squashfs + f2fs combined images.
To make place, for saving config, kernel space ar now ext4 partition
with fit kernel.
This method of image generation is similar to rest of OpenWrt sd-card
targets.
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[reword README, reword DEVICE_COMPAT_MESSAGE, keep original indent]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
| |
Many Layerscape boards support both flash boot and SD card boot.
And different firmware and sysupgrade.bin are built for the two
boot methods. To identify them, a fix could be done on board name
by adding a postfix "-sdboot" for SD card boot.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.
Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.
This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.
Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
|