aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ipq40xx/files-6.6/arch/arm/boot
Commit message (Collapse)AuthorAge
* ipq40xx: Properly set MAC addresses for the EAP1300Corey Minyard2024-05-06
| | | | | | | | | | The code that was there was just taking whatever was left in the registers, which was just wrong. Set the addresses using the value from the u-boot environment, the same way the OEM firmware does. Signed-off-by: Corey Minyard <minyard@acm.org> Link: https://github.com/openwrt/openwrt/pull/15358 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: convert Engenius EAP1300 to DSACorey Minyard2024-05-06
| | | | | | | | This commit converts the EAP1300 to DSA setup. Signed-off-by: Corey Minyard <minyard@acm.org> Link: https://github.com/openwrt/openwrt/pull/15358 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq4019: fix even more wrong reference to USB nodeChristian Marangi2024-05-06
| | | | | | | | | | | Commit 6136ebabc5cb ("ipq40xx: 6.6: fix DTS to use reference for usb node") fixed only some of the reference to USB node but many others were still using the old broken usb3/usb2. Fix every reference to those node and move them on using the tag name. Fixes: 6136ebabc5cb ("ipq40xx: 6.6: fix DTS to use reference for usb node") Link: https://github.com/openwrt/openwrt/pull/15392 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: merge DTS for Linksys WHW03 V1 and V2Rodrigo Balerdi2024-05-05
| | | | | | | | No changes other than the merging itself are intended in this commit. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15345 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: clean up Linksys WHW03 V2 DTSRodrigo Balerdi2024-05-05
| | | | | | | | Apply stylistic changes to facilitate DTS merging with WHW03 V1. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15345 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add support for Linksys WHW03 V1Rodrigo Balerdi2024-05-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: ========= SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA9886 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8510 (A10) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash: Samsung KLM4G1FEPD (4GB eMMC) RAM (NAND): 512MB LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). Ethernet: ========= The device has 2 ethernet ports, configured as follows by default: - left port: WAN - right port: LAN Wifi: ===== The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Bluetooth and Zigbee: ===================== Configuration included but not tested. Storage: ======== For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB eMMC partition (of which there are two copies, see below). You can also use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit. During very limited tests, stock firmware did not mount this partition. However, backing up its stock content before use is recommended anyway. Firmware: ========= The device uses a dual firmware mechanism: it automatically reverts to the previous firmware after 3 failed boot attempts. You can switch to the inactive firmware copy by changing the "boot_part" U-Boot environment variable. You can also do it by turning on the device for a couple of seconds and then back off, 3 times in a row. Installation: ============= OpenWrt's "factory" image can be installed via the stock web UI: 1. Login to the UI. (The default password is printed on the label.) 2. Enter support mode by clicking on the "CA" link at the bottom. 3. Click "Connectivity", "Choose file", "Start", and ignore warnings. This port is based on work done by flipy (https://github.com/flipy). Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15345 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: fritzrepeater-1200: fix MDIO and PHY probingRobert Marko2024-05-02
| | | | | | | | | | | | | | AVM FRITZ!Repeater 1200 does not use QCA807x PHY at all and thus it disables all of the individual PHY nodes, however this is not enough anymore since the conversion to PHY package. Now its now enough to disable the PHY-s in the package alone, but the PHY package node itself must also be disabled. Fixes: 1b931c33a28e ("ipq40xx: adapt to new Upstream QCA807x PHY driver") Fixes: #15355 Link: https://github.com/openwrt/openwrt/pull/15365 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: fix I2C pin config on Aruba AP-303HRyan Salsbury2024-04-30
| | | | | | | | | | | | | Turn on SoC pull-ups on I2C pins, since there are no discrete pull-up resistors on the bus. Increase clock to 400 kHz. Both chips on the bus support 400 kHz. I tested the ISL28022 at 4,000 reads/sec and didn't see any garbled output or bus hangs, even with SoC drive strength reduced to 2 for the test. Signed-off-by: Ryan Salsbury <ryanrs@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15334 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: fix USB on Aruba AP-303HRyan Salsbury2024-04-27
| | | | | | | | | | Enable USB 3.0 controller, disable USB 2.0 controller. The USB 2.0 port on the AP-303H is actually connected to the USB 3.0 controller's HS phy. Enable the HS phy only, since the SS lanes are not brought out to the connector. Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
* ipq40xx: use nvmem ethernet MACs on Aruba AP-303HRyan Salsbury2024-04-27
| | | | | | | Use NVMEM to assign "factory sticker" MAC address to WAN ethernet interface. Set LAN address to sticker + 1. Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
* ipq40xx: whw03v2: enable additional 5 GHz channelsRodrigo Balerdi2024-04-16
| | | | | | | | This device supports channel ranges 36-64 and 100-165, just like others based on the same reference design, but its current DTS is unnecessarily restricting these ranges to 36-48 and 149-165. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ipq40xx: whw03v2: change LED color for 'running' state to blueRodrigo Balerdi2024-04-13
| | | | | | | | | | | | | | | | | | | | Change the RGB indicator LED color for the running state from green to blue. There are various reasons for this change: - In stock firmware, green means internet connection is up, red means it is down, and blue means indeterminate. To track stock behavior as closely as possible, OpenWrt should indicate blue by default. - In the current 23.x OpenWrt releases for this router, the led glows blue all the time -not green- because the bootloader sets it blue and there is an OpenWrt bug that makes it unable to control the LED. The bug is fixed in master, so without this commit there would be an unexpected change of behavior for this device in the next release. - The ports other closely related Linksys devices (such as EA8300 and MR8300) get this right and use blue for the running state. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ipq40xx: whw03v2: fix handling of RGB LEDRodrigo Balerdi2024-04-13
| | | | | | | The RGB LED should glow green in the 'running' state, but it was glowing cyan because the blue component defaulted to 'on'. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ipq40xx: 6.6: fix DTS to use reference for usb nodeChristian Marangi2024-04-02
| | | | | | | Fix DTS to use reference for usb node instead of redefining them since upstream usb node names changed from usb2/3 to usb. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: split files in 6.1 and 6.6 dedicated directoryChristian Marangi2024-04-02
Since with recent kernel version DTS moved to a dedicated directory, it's required to split files to per kernel version to follow kernel version directory structure. Also makes use of DEVICE_DTS_DIR to target the correct DTS directory based on the kernel version. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Powered by cgit, Themed by Ted Yin.