| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
| |
The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.
Fixes FS#790.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
| |
|
|
|
|
|
|
|
|
| |
Remove the code used on the old switch driver.
The Ethernet drive is loaded as a module and needs some time to get up
therefor we added some wait function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39254
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes some problems with the switch handling
* It now send the messages again to indicate a button for failsafe mode should be pressed
* it does not leak packages between wan and lan any more
* the switch works again in normal mode
The Ethernet connection has to be up when the switch driver switch-robo
is insmoded therefor we just do it again.
Explicitly set enable_vlan to prevent leaking packages.
This should close #13869, #13868 and #13716
SVN-Revision: 37286
|
| |
|
|
|
|
|
| |
add the boot flag to make the kernel modules needed for Ethernet and
diag load on startup.
SVN-Revision: 37284
|
| |
|
|
|
|
| |
Signed-off-by: John Crispin <bloic@openwrt.org>
SVN-Revision: 36993
|
| |
|
|
|
|
|
| |
Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X
Ask the switch driver where the CPU port is.
SVN-Revision: 35624
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35491
|
| |
|
|
|
|
| |
for failsafe.
SVN-Revision: 35341
|
| |
|
|
|
|
|
|
|
| |
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
SVN-Revision: 34995
|
| |
|
|
| |
SVN-Revision: 34994
|
| |
|
|
|
|
| |
In addition check_module is not needed, nobody checks the return value.
SVN-Revision: 34993
|
| |
|
|
|
|
|
|
| |
function.
Thank you Bastian Bittorf
SVN-Revision: 34680
|
| |
|
|
| |
SVN-Revision: 34653
|
| |
|
|
| |
SVN-Revision: 34652
|
| |
|
|
| |
SVN-Revision: 34329
|
|
|
SVN-Revision: 21945
|