aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ath79/image
Commit message (Collapse)AuthorAge
* ath79: add support for Comfast CF-EW71 v2Felix Golatofski2024-04-14
| | | | | | | | | | | | | | | | | | Specifications: Qualcomm/Atheros QCA9531 2x 10/100 Mbps Ethernet, with 48v PoE 2T2R 2.4 GHz, 802.11b/g/n 128MB RAM 16MB SPI Flash 4x LED (Always On Power, LAN, WAN, WLAN) Flashing instructions: The original firmware is based on OpenWrt, so flashing the sysupgrade image over the factory firmware is sufficient. The bootloader has a built-in recovery web-ui. This is the method I used to flash OpenWrt. You can get to the recovery web-ui by holding down the reset button for a few seconds (~5s) while pluggin in the router. The LEDs should start blinking fast and the router should be available on 192.168.1.1 for the recovery. Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much to test), WLAN LED, MAC addresses (same as factory firmware). Signed-off-by: Felix Golatofski <git@xdfr.de>
* ath79: add support for Huawei AP5030DNMarco von Rosenberg2024-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO enterprise access point with two Gigabit Ethernet ports and PoE support. Hardware highlights: - CPU: QCA9550 SoC at 720MHz - RAM: 256MB DDR2 - Flash: 32MB SPI-NOR - Wi-Fi 2.4GHz: QCA9550-internal radio - Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC - Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY - Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY - PoE: input through Ethernet 1 port - Standalone 12V/2A power input - Serial console externally available through RJ45 port - External watchdog: SGM706 (1.6s timeout) Serial console: 9600n8 (9600 baud, no stop bits, no parity, 8 data bits) MAC addresses: Each device has 32 consecutive MAC addresses allocated by the vendor, which don't overlap between devices. This was confirmed with multiple devices with consecutive serial numbers. The MAC address range starts with the address on the label. To be able to distinguish between the interfaces, the following MAC address scheme is used: - eth0 = label MAC - eth1 = label MAC + 1 - radio0 (Wi-Fi 5GHz) = label MAC + 2 - radio1 (Wi-Fi 2.4GHz) = label MAC + 3 Installation: 0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP 1. Power up the AP 2. At prompt "Press f or F to stop Auto-Boot in 3 seconds", do what they say. Log in with default admin password "admin@huawei.com". 3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot". Replace IP address as needed: > setenv serverip 192.168.1.10 > setenv ipaddr 192.168.1.1 > setenv rambootfile openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin > saveenv > run ramboot 4. Optional but recommended as the factory firmware cannot be downloaded publicly: Back up contents of "firmware" partition using the web interface or ssh: $ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin 5. Run sysupgrade using sysupgrade image. OpenWrt shall boot from flash afterwards. Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website): 1. Start a TFTP server in the directory where the firmware upgrade package is located 2. Boot to u-boot as described above 3. Install firmware upgrade package and format the config partitions: > update system FatAP5X30XN_SOMEVERSION.bin > format_fs Return to factory firmware (from previously created backup): 1. Copy over the firmware partition backup to /tmp, for example using scp 2. Use sysupgrade with force to restore the backup: sysupgrade -F huawei_ap5030dn_fw_backup.bin 3. Boot AP to U-Boot as described above Quirks and known issues ----------------------- - On initial power-up, the Huawei-modified bootloader suspends both ethernet PHYs (it sets the "Power Down" bit in the MII control register). Unfortunately, at the time of the initial port, the kernel driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume callback defined which would clear this bit. This makes the PHY unusable since it remains suspended forever. This is why the backported kernel patches in this commit are required which add this callback and for completeness also a suspend callback. - The stock firmware has a semi dual boot concept where the primary kernel uses a squashfs as root partition and the secondary kernel uses an initramfs. This dual boot concept is circumvented on purpose to gain more flash space and since the stock firmware's flash layout isn't compatible with mtdsplit. - The external watchdog's timeout of 1.6s is very hard to satisfy during bootup. This is why the GPIO15 pin connected to the watchdog input is configured directly in the LZMA loader to output the CPU_CLK/4 signal which keeps the watchdog happy until the wdt-gpio kernel driver takes over. Because it would also take too long to read the whole kernel image from flash, the uImage header only includes the loader which then reads the kernel image from flash after GPIO15 is configured. Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de> [fixed 6.6 backport patch naming] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: move D-Link DAP-1720 A1 to tiny sub-targetShiji Yang2024-03-30
| | | | | | | | | | | This device only has 64 MiB RAM and ath10k wireless driver will consume a lot of memory. Let's move it to the tiny sub-target to get extra 7 MiB of free space. In this way, we can extend their lifetime to receive support for the next OpenWrt LTS version. This patch also trims the duplicate "recovery.bin" image as it's the same as the "factory.bin". Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move D-Link DIR-859 and DIR-869 series to tiny sub-targetShiji Yang2024-03-30
| | | | | | | | | | These devices only have 64 MiB RAM and ath10k wireless driver will consume a lot of memory. Let's move them to the tiny sub-target to get extra 7 MiB of free space. In this way, we can extend their lifetime to receive support for the next OpenWrt LTS version. This patch also trims the USB package for the non-existent USB port. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move seama image recipe to the common MakefileShiji Yang2024-03-30
| | | | | | | Move seama image recipe to the common Makefile in order for some tiny sub-target D-Link devices can share it. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: disable building small Flash EnGenius devicesShiji Yang2024-03-30
| | | | | | | The buildbot has not successfully built them for a long time due to small Flash size. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add support for D-Link COVR-C1200 A1Sebastian Schaper2024-03-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The COVR-C1200 devices are sold as "Whole Home Mesh Wi-Fi" sets in packs of two (COVR-C1202) and three (COVR-C1203). Specifications: * QCA9563, 16 MiB flash, 128 MiB RAM, 2x3:2 802.11n * QCA9886 2x2:2 801.11ac Wave 2 * AR8337, 2 Gigabit ports (1: WAN; 2: LAN) * USB Type-C power connector (5V, 3A) Installation COVR Point A: * In factory reset state: OEM Web UI is at 192.168.0.50 no DHCP, skip wizard by directly accessing: http://192.168.0.50/UpdateFirmware_Simple.html * After completing setup wizard: Web UI is at 192.168.0.1 DHCP enabled, login with empty password * Flash factory.bin * Perform a factory reset to restore OpenWrt UCI defaults Installation COVR Points B: * OEM Web UI is at 192.168.0.50, no DHCP, empty password * Flash factory.bin * Perform a factory reset to restore OpenWrt UCI defaults Recovery: * Keep reset button pressed during power on * Recovery Web UI is at 192.168.0.50, no DHCP * Flash factory.bin used to work best with Chromium-based browsers or curl: curl -F firmware=@factory.bin \ http://192.168.0.50/upgrade.cgi since this fails to work on modern Linux systems, there is also a script dlink_recovery_upload.py Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: split dtsi for D-Link COVR-P2500Sebastian Schaper2024-03-09
| | | | | | in preparation of adding COVR-C1200 Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: add support for ELECOM WAB-I1750-PSINAGAKI Hiroshi2024-03-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point, based on QCA9558. Specification: - SoC : Qualcomm Atheros QCA9558 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 3T3R - 2.4 GHz : Qualcomm Atheros QCA9558 (SoC) - 5 GHz : Qualcomm Atheros QCA9880 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 2x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - "SERIAL" : RS232C (+-12V) - port : ? - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - settings : 115200n8 - note : compatible with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1.04 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-I1750-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - "SERIAL" port is provided by HS UART on QCA9558 SoC that has compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported on Linux Kernel and OpenWrt. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text)) 2.4GHz : 00:90:FE:xx:xx:0A (Config, ethaddr (text)) 5GHz : 00:90:FE:xx:xx:0B [original work] Signed-off-by: Yanase Yuki <dev@zpc.st> [update for NVMEM and others] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for ELECOM WAB-S1167-PSINAGAKI Hiroshi2024-03-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point, based on QCA9557. Specification: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm Atheros QCA9557 (SoC) - 5 GHz : Qualcomm Atheros QCA9882 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 1x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-S1167-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - The same PCB is used with WAB-S600-PS. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text)) 2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text)) 5GHz : 00:90:FE:xx:xx:05 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for ELECOM WAB-S600-PSINAGAKI Hiroshi2024-03-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based on QCA9557. This device also supports 11ac (Wi-Fi 5) with the another official firmware. Specification: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm Atheros QCA9557 (SoC) - 5 GHz : Qualcomm Atheros QCA9882 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 1x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-S600-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - The same PCB is used with WAB-S1167-PS. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text)) 2.4GHz : BC:5C:4C:xx:xx:7C (Config, ethaddr (text)) 5GHz : BC:5C:4C:xx:xx:7D [original work of common dtsi part for WAB-I1750-PS] Signed-off-by: Yanase Yuki <dev@zpc.st> [adding support for WAB-S600-PS] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: nand: add SUPPORTED_DEVICES for Meraki MR18Samuele Longhi2024-02-29
| | | | | | | This adds the board name from ar71xx to support upgrade without -F for the Meraki MR18. Signed-off-by: Samuele Longhi <agave@dracaena.it>
* ath79: update WA/XC devices UBNT_VERSION to 8.7.4Martin Garbe2024-02-19
| | | | | | | | | | Ubiquiti WA devices with newer hw version (sold 2023) require UBNT_VERSION to be at least 8.7.4, otherwise the image is rejected. For consistency, also increase version number for XC devices. Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
* ath79: add WWAN serial driver and qmi for GL.iNET GL-E750 (Mudi)Jan Fuchs2024-02-02
| | | | | | | | The driver for the cellular modems serial interface and qmi was missing from the default device packages. The driver is required to interact with the modem using AT commands. Signed-off-by: Jan Fuchs <jf@simonwunderlich.de>
* ath79: add Ubiquiti Rocket M XW as alternate name to Bullet M XWLech Perczak2024-01-25
| | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti Rocket M XW is a single-band, 2x2:2 external Wi-Fi AP, with optional GPS receiver, with two external RP-SMA antenna connections, based on AR9342 SoC. Two band variants exists, for 2.4GHz and 5GHz band, usable with the same image. Specs: - CPU: Atheros AR9342 MIPS SoC at 535MHz - RAM: 64MB DDR400 - ROM: 8MB SPI-NOR in SO16W package, MX25L6408E - Wi-Fi Atheros AR9342 built-in 2x2:2 radio - Ethernet: Atheros AR8035 PHY, limited to 100Mbps speeds due to magnetics - Power: 24V passive PoE input. Installation: please refer to Ubiquiti Bullet M2HP for documentation. The device runs with exactly same image as the Bullet, and after fixes in preceding commit, is fully functional again. Add the alternative name to the build system. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti ↵Samuele Longhi2024-01-20
| | | | | | | | | | | | | | | | | | | | | | | | | | LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) Add support for Ubiquiti LiteBeam M5 (XW). The device was previously supported in ar71xx. See commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d0988235dd277b9a832bbc4b2a100ac6e821f577 Add ALTX_MODEL for Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) in generic-ubnt.mk This models are identical (firmware-wise) to the already supported Ubiquiti Nanostation Loco M (XW) Add also Ubiquiti NanoBeam M5 to ALTX_MODEL of Ubiquiti Nanostation Loco M (XW) since it's another clone. Tested on: - Ubiquiti LiteBeam M5 (XW) - Ubiquiti PowerBeam M5 (XW) This also modify target/ath79/dts/ar9342_ubnt_xw.dtsi to use nvmem for calibration data Checked that the caldata size in the eeprom partition are actually 0x440 on: - Ubiquiti PowerBeam M5 (XW) - Ubiquiti Nanostation M5 (XW) - Ubiquiti LiteBeam M5 (XW) - Ubiquiti AirGrid M5 HP (XW) Signed-off-by: Samuele Longhi <agave@dracaena.it>
* ath79: add support for UniFi UK-UltraDavid Bauer2024-01-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9563 RAM: 128M DDR2 FLASH: 16MB SPI-NOR WiFi: Qualcomm Atheros QCA9563 2x2:2 802.11n 2.4GHz Qualcomm Atheros QCA9880 2x2:2 802.11ac 5GHz Antennas -------- The device features internal antennas as well as external antenna connectors. By default, the internal antennas are used. Two GPIOs are exported by name, which can be used to control the antenna-path mux. Writing a logical 0 enables the external antenna connectors. Installation ------------ 1. Download the OpenWrt sysupgrade image to the device. You can use scp for this task. The default username and password are "ubnt" and the device is reachable at 192.168.1.20. $ scp -O openwrt-sysupgrade.bin ubnt@192.168.1.20:/tmp/firmware.bin 2. Connect to the device using SSH. $ ssh ubnt@192.168.1.20 3. Disable the write-protect $ echo "5edfacbf" > /proc/ubnthal/.uf 4. Verify kernel0 and kernel1 match mtd2 and mtd3 $ cat /proc/mtd 5. Write the sysupgrade image to kernel0 and kernel1 $ dd if=/tmp/firmware.bin of=/dev/mtdblock2 $ dd if=/tmp/firmware.bin of=/dev/mtdblock3 6. Write the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtd4 7. Reboot the device $ reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: move UniFi AC template into commonDavid Bauer2024-01-07
| | | | | | This allows us to embrace alphabetical sorting for the UK-Ultra. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: support MikroTik RouterBOARD 911G-5HPacDLech Perczak2024-01-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik RouterBOARD 911G-5HPacD is a stripped-down version of RB921GS-5HPacD, removing the SFP cage. This ports the board from ar71xx, and is based on support for RB921GS-5HPacD. Disable mdio1 and eth1 nodes in routerboard-92x.dtsi, then re-enable them in devices using that, so the newly-added device has the port disabled properly. See https://mikrotik.com/product/RB911G-5HPacD for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9892 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in Working: - NAND storage detection - Ethernet - Wireless - 1x user LED (blinks during boot, sysupgrade) - Reset button - Sysupgrade Installation: - Boot initramfs image via TFTP and then flash sysupgrade image Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: mikrotik: add rssileds support for Routerboard 911G and RB912UAGLech Perczak2024-01-07
| | | | | | | LEDs 1 through 5 are used for RSSI monitoring on factory firmware. Reflect that by creating appropriate rssileds configuration. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: support for MikroTik RouterBOARD 911G-(2,5)HPnDLech Perczak2024-01-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a stripped-down version of RB912UAG-(2,5)HPnD, without USB, miniPCIe and SIM sockets. This board has been supported in the ar71xx. Add support based on RB912UAG board, by splitting out the common part to .dtsi, and creating separate device tree for the stripped-down version. Links: * https://mikrotik.com/product/RB911G-2HPnD * https://mikrotik.com/product/RB911G-5HPnD * https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb911g-5hpnd Hardware: * SoC: Atheros AR9342, * RAM: DDR 64MB, * SPI NOR: 64KB, * NAND: 128MB, * Ethernet: x1 10/100/1000 port with passive POE in, * Wi-Fi: 802.11 a/b/g/n (depending on band variant) * LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED, Ethernet phy LED, * Button, * Beeper. Flashing: * Use the RouterBOARD Reset button to enable TFTP netboot, boot kernel and initramfs and then perform sysupgrade. * From ar71xx OpenWrt firmware run: $ sysupgrade -F /tmp/<sysupgrade.bin> For more info see: https://openwrt.org/toh/mikrotik/common. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: mikrotik: add RB912UAG-5HPnD as alternative nameLech Perczak2024-01-07
| | | | | | | | | Image for RB912UAG-2HPnD supports the 5GHz variant without modifications. Add it as alternative name, so it can be found easier. While at that, adjust board display name in device tree, to reflect that. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* image: use helper function for size unitsTony Ambardar2023-11-26
| | | | | | | | Add the make function 'exp_units' for helping evaluate k/m/g size units in expressions, and use this to consistently replace many ad hoc substitutions like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for D-link DAP-1720 A1Rani Hod2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa <protectivedad@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ath79: add support for D-Link COVR-P2500 A1Daniel Linjama2023-11-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * QCA9563, 16 MiB flash, 128 MiB RAM, 2T2R 802.11n * QCA9886 2T2R 801.11ac Wave 2 * QCA7550 Homeplug AV2 1300 * AR8337, 3 Gigabit ports (1, 2: LAN; 3: WAN) To make use of PLC functionality, firmware needs to be provided via plchost (QCA7550 comes without SPI NOR), patched with the Network Password and MAC. Flashing via OEM Web Interface * Flash 'factory.bin' using web-interface * Wait until firmware succesfully installed and device booted * Hold down reset button to reset factory defaults (~10 seconds) Flashing via Recovery Web Interface: * Hold down reset button during power-on (~10 seconds) * Recovery Web UI is at 192.168.0.50, no DHCP. * Flash 'recovery.bin' with scripts/flashing/dlink_recovery_upload.py (Recovery Web UI does not work with modern OSes) Return to stock * Hold down reset button during power-on (~10 seconds) * Recovery Web UI is at 192.168.0.50, no DHCP. * Flash unencrypted stock firmware with scripts/flashing/dlink_recovery_upload.py (Recovery Web UI does not work with modern OSes) Co-developed-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Daniel Linjama <daniel@dev.linjama.com>
* ath79: support Fortinet FAP-220-BLech Perczak2023-11-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fortinet FAP-220-B is a dual-radio, dual-band 802.11n enterprise managed access point with PoE input and single gigabit Ethernet interface. Hardware highlights: Power: 802.3af PoE input on Ethernet port, +12V input on 5.5/2.1mm DC jack. SoC: Atheros AR7161 (MIPS 24kc at 680MHz) RAM: 64MB DDR400 Flash: 16MB SPI-NOR Wi-Fi 1: Atheros AR9220 2T2R 802.11abgn (dual-band) Wi-Fi 2: Atheros AR9223 2T2R 802.11bgn (single-band) Ethernet: Atheros AR8021 single gigabit Phy (RGMII) Console: External RS232 port using Cisco 8P8C connector (9600-8-N-1) USB: Single USB 2.0 host port LEDs: Power (single colour, green), Wi-Fi 1, Wi-Fi 2, Ethernet, Mode, Status (dual-colour, green and yellow) Buttons: reset button hidden in bottom grill, in the top row, 2nd column from the right. Label MAC address: eth0 FCC ID: TVE-220102 Serial port pinout: 3 - TxD 4 - GND 6 - RxD Installation: The same methods apply as for already supported FAP-221-B. For both methods, a backup of flash partitions is recommended, as stock firmware is not freely available on the internet. (a) Using factory image: 1. Connect console cable to the console port 2. Connect Ethernet interface to your PC 3. Start preferred terminal at 9600-8-N-1 4. Have a TFTP server running on the PC. 5. Put the "factory" image in TFTP root 6. Power on the device 7. Break boot sequence by pressing "Ctrl+C" 8. Press "G". The console will ask you for device IP, server IP, and filename. Enter them appropriately. The defaults are: Server IP: 192.168.1.1 # Update accordingly Device IP: 192.168.1.2 # Update accordingly Image file: image.out # Use for example: openwrt-ath79-generic-fortinet_fap-220-b-squashfs-factory.bin 9. The device will load the firmware over TFTP, and verify it. When verification passes, press "D" to continue installation. The device will reboot on completion. (b) Using initramfs + sysupgrade 1. Connect console cable to the console port 2. Connect Ethernet interface to your PC 3. Start preferred terminal at 9600-8-N-1 4. Have a TFTP server running on the PC. 5. Put the "initramfs" image in TFTP root 6. Power on the device. 7. Break boot sequence by pressing "Ctrl+C" 8. Enter hidden U-boot shell by pressing "K". The password is literal "1". 9. Load the initramfs over TFTP: > setenv serverip 192.168.1.1 # Your PC IP > setenv ipaddr 192.168.1.22 # Device IP, both have to share a subnet. > tftpboot 81000000 openwrt-ath79-generic-fortinet_fap-220-b-initramfs-kernel.bin > bootm 81000000 10. (Optional) Copy over contents of at least "fwconcat0", "loader", and "fwconcat1" partitions, to allow restoring factory firmware in future: # cat /dev/mtd1 > /tmp/mtd1_fwconcat0.bin # cat /dev/mtd2 > /tmp/mtd2_loader.bin # cat /dev/mtd3 > /tmp/mtd3_fwconcat1.bin and then SCP them over to safety at your PC. 11. When the device boots, copy over the sysupgrade image, and execute normal upgrade: # sysupgrade openwrt-ath79-generic-fortinet_fap-220-b-squashfs-sysupgrade.bin Return to stock firmware: 1. Boot initramfs image as per initial installation up to point 9 2. Copy over the previously backed up contents over network 3. Write the backed up contents back: # mtd write /tmp/mtd1_fwconcat0.bin fwconcat0 # mtd write /tmp/mtd2_loader.bin loader # mtd write /tmp/mtd3_fwconcat1.bin fwconcat1 4. Erase the reserved partition: # mtd erase reserved 5. Reboot the device Quirks and known issues: - The power LED blinking pattern is disrupted during boot, probably due to very slow serial console, which prints a lot during boot compared to stock FW. - "mac-address-ascii" device tree binding cannot yet be used for address stored in U-boot partition, because it expects the colons as delimiters, which this address lacks. Addresses found in ART partition are used instead. - Due to using kmod-owl-loader, the device will lack wireless interfaces while in initramfs, unless you compile it in. - The device heats up A LOT on the bottom, even when idle. It even contains a warning sticker there. - Stock firmware uses a fully read-write filesystem for its rootfs. - Stock firmware loads a lot of USB-serial converter drivers for use with built-in host, probably meant for hosting modem devices. - U-boot build of the device is stripped of all branding, despite that evidence of it (obviously) being U-boot can be found in the binary. - The user can break into hidden U-boot shell using key "K" after breaking boot sequence. The password is "1" (without quotes). - Telnet is available by default, with login "admin", without password. The same is true for serial console, both drop straight to the Busybox shell. - The web interface drops to the login page again, after successfull login. - Whole image authentication boils down to comparing a device ID against one stored in U-boot. - And this device is apparently made by a security company. Big thanks for Michael Pratt for providing support for FAP-221-B, which shares the entirety of image configuration with this device, this saved me a ton of work. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: image: extract common part for Fortinet FAP seriesLech Perczak2023-11-03
| | | | | | | In preparation for FAP-220-B support, extract the common part of image recipe for FAP-221-B. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for GL.iNet GL-S200Weiping Yang2023-10-31
| | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9531(650MHz) RAM: DDR2 128M Flash: SPI NOR 16M + SPI NAND 128M WiFi: 2.4GHz with 2 antennas(WiFi/Thread) Ethernet: 1xLAN(10/100M) 2xWAN(10/100M) Button: 1x Reset Button Switch: 1x Mode switch LED: 1x Blue LED + 1x White LED + 1x Orange LED IOT: Thread + ZigBee/Zwave By uboot web failsafe: Push the reset button for 5 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ath79: add WWAN serial driver for GL.iNET GL-XE300David Bauer2023-10-09
| | | | | | | | | | | The driver for the cellular modems serial interface was missing from the default device packages. The driver is required to interact with the modem using AT commands. Other devices with a 4G modem also ship with this package, thus let's add it to the default packages for the board. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite)Roger Pueyo Centelles2023-09-16
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one with PoE in. The device was already supported by the ar71xx target. Specifications: - SoC: Qualcomm Atheros QCA9533 - Flash: 16 MB SPI NOR - RAM: 64 MB - Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in) - LEDs: 5x Ethernet port activity (green), 1x user (green) - Buttons: 1x reset See https://mikrotik.com/product/RB750r2 for more details. Not working: - Serial port (already not working in ar71xx) Flashing: TFTP boot initramfs image and then perform sysupgrade. Only the "Internet" port will ask for an initramfs image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: fix first reboot issue on Netgear WNDR4300 v2 and WNDR4500 v3Shiji Yang2023-08-24
| | | | | | | | | | | | | | | From the Netgear u-boot GPL code[1]. Bootloader always unconditionally marks block 768, 1020 - 1023 as bad blocks on each boot. This may lead to conflicts with the OpenWrt nand driver since these blocks may be good blocks. In this case, U-boot will override the oob of these blocks so that break the ubi volume. The system will be damaged after first reboot. To avoid this issue, manually skip these blocks by using "mtd-concat". [1] https://www.downloads.netgear.com/files/GPL/EX7300v2series-V1.0.0.146_gpl_src.tar.bz2.zip Fixes: https://github.com/openwrt/openwrt/issues/8878 Tested-by: Yousaf <yousaf465@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: rework Netgear nand devices image recipeShiji Yang2023-08-24
| | | | | | | | | | | | | | | | | | In Netgear u-boot GPL code, nand devices uses this formula to locate the rootfs offset. offset = (((128 + KERNEL_SIZE) / BLOCK_SIZE) + 1) * BLOCK_SIZE; Howerver, WNDR4500 source code incorrectly define the nand block size to 64k. In some cases, it causes u-boot can't get the correct rootfs offset, which result in boot failure. This patch workaround it by padding kernel size to (128k * n - 128 - 1). The additional char '\0' is used to ensure the (128 + KERNEL_SIZE) can't be divided by the BLOCK_SIZE. Fixes: https://github.com/openwrt/openwrt/issues/13050 Fixes: 3c1512a25d92 ("ath79: optimize the firmware recipe for Netgear NAND devices") Tested-by: Yousaf <yousaf465@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move ubnt-xm 64M RAM boards back to genericFelix Baumann2023-07-19
| | | | | | | | | return ubnt_rocket-m and ubnt_powerbridge-m back to ath79-generic They have enough RAM-ressources to not be considered as tiny. This reverts the commit f4415f7635164ec07ddc22f56df93555804b5767 partially Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ath79: add support for ASUS RT-AC59U / ZenWiFi CD6Wenli Looi2023-07-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP, RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12. ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R is the router, and CD6N is the node. Hardware: - SoC: QCN5502 - RAM: 128 MiB - UART: 115200 baud (labeled on boards) - Wireless: - 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n currently unsupported due to missing support for QCN550x in ath9k - 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac - Flash: SPI NOR - RT-AC59U / CD6N: 16 MiB - RT-AC59U v2 / CD6R: 32 MiB - Ethernet: gigabit - RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN - CD6R: 3x LAN 1x WAN - CD6N: 2x LAN - USB: - RT-AC59U / RT-AC59U v2: 1 port USB 2.0 - CD6R / CD6N: none WiFi calibration data contains valid MAC addresses. The initramfs image is uncompressed because I was unable to boot a compressed initramfs from memory (gzip or lzma). Booting a compressed image from flash works fine. Installation: To install without opening the case: - Set your computer IP address to 192.168.1.10/24 - Power up with the Reset button pressed - Release the Reset button after about 5 seconds or until you see the power LED blinking slowly - Upload OpenWRT factory image via TFTP client to 192.168.1.1 Revert to stock firmware using the same TFTP method. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ath79: add support for COMFAST CF-E380AC v2Joao Henrique Albuquerque2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) COMFAST MAC addresses : Though the OEM firmware has four adresses in the usual locations, it appears that the assigned addresses are just incremented in a different way: Interface address location Lan *:00 0x0 2.4g *:0A n/a (0x0 + 10) 5g *:02 0x6 Unused Addresses found in ART hexdump address location *:01 0x1002 *:03 0x5006 To keep code consistency the MAC address assignments are made based on increments of the one found in 0x0; Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
* ath79: add support for MikroTik RB951G-2HnDMichał Kępień2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951G-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add kernel support for the Mikrotik RB951G board"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s - 1x PoE in (port 1, 8-30 V input) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 8x LED: - 1x power (green, not configurable) - 1x user (green, not configurable) - 5x GE ports (green, not configurable) - 1x wireless (green, not configurable) - 1x button (restart) Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be GPIO-controllable, which was also the case for older OpenWRT versions that supported this board via a mach file. The Ethernet port LEDs are controlled by the switch chip. See https://mikrotik.com/product/RB951G-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* ath79: Add support for MOXA AWK-1137CMaximilian Martin2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 * 128 MB of RAM * 16 MB of SPI NOR flash * 2x 10/100 Mbps Ethernet * 2T2R 2.4/5 GHz Wi-Fi * 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * 2x fast ethernet - lan1 + builtin switch port 1 + used as WAN interface - lan2 + builtin switch port 2 + used as LAN interface * 9-30V DC * external antennas Flashing instructions: ====================== Log in to https://192.168.127.253/ Username: admin Password: moxa Open Maintenance > Firmware Upgrade and install the factory image. Serial console access: ====================== Connect a RS232-USB converter to the maintenance port. Pinout: (reset button left) [GND] [NC] [RX] [TX] Firmware Recovery: ================== When the WLAN and SYS LEDs are flashing, the device is in recovery mode. Serial console access is required to proceed with recovery. Download the original image from MOXA and rename it to 'awk-1137c.rom'. Set up a TFTP server at 192.168.127.1 and connect to a lan port. Follow the instructions on the serial console to start the recovery. Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
* ath79: add support for Aruba AP-115David Bauer2023-06-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU Qualcomm Atheros QCA9558 RAM 256MB DDR2 FLASH 2x 16M SPI-NOR (Macronix MX25L12805D) WIFI Qualcomm Atheros QCA9558 Atheros AR9590 Installation ============ 1. Attach to the serial console of the AP-105. Interrupt autoboot and change the U-Boot env. $ setenv rb_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; netget 0x80060000 ap115.bin; go 0x80060000" $ setenv fb_openwrt "bank 1; cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000" $ setenv bootcmd "run fb_openwrt" $ saveenv 2. Load the OpenWrt initramfs image on the device using TFTP. Place the initramfs image as "ap105.bin" in the TFTP server root directory, connect it to the AP and make the server reachable at 192.168.1.66/24. $ run rb_openwrt 3. Once OpenWrt booted, transfer the sysupgrade image to the device using scp and use sysupgrade to install the firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WDR6500 v2Xiaobing Luo2023-06-11
| | | | | | | | | | | | | | | | | | | | | | | This ports the TP-Link TL-WDR6500 v2 from ar71xx to ath79. Specifications: SoC: QCA9561 CPU: 750 MHz Flash: 8 MiB (Winbond W25Q64FVSIG) RAM: 128 MiB WiFi 2.4 GHz: QCA956X 3x3 MIMO 802.11b/g/n WiFi 5 GHz: QCA9882-BR4A 2x2 MIMO 802.11a/n/ac Ethernet: 4x LAN and 1x WAN (all 100M) USB: 1x Header Flashing instructions: As it appears, the device does not support flashing via GUI or TFTP, only serial is possible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Xiaobing Luo <luoxiaobing0926@gmail.com>
* ath79: add support for D-Link DIR-859 A3Shiji Yang2023-05-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: QCA9563 775 MHz + QCA9880 Switch: QCA8337N-AL3C RAM: Winbond W9751G6KB-25 64 MiB Flash: Winbond W25Q128FVSG 16 MiB WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3 LAN: LAN ports *4 WAN: WAN port *1 Buttons: reset *1 + wps *1 LEDs: ethernet *5, power, wlan, wps MAC Address: use address source1 source2 label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr lan 40:9b:xx:xx:xx:3c devdata@0x3f $label wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3 wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2 Install via Web UI: Apply factory image in the stock firmware's Web UI. Install via Emergency Room Mode: DIR-859 A1 will enter recovery mode when the system fails to boot or press reset button for about 10 seconds. First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1. Then we can open http://192.168.0.1 in the web browser to upload OpenWrt factory image or stock firmware. Some modern browsers may need to turn on compatibility mode. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* treewide: Disable building 32M RAM devicesFelix Baumann2023-05-21
| | | | | | | | Following deprecation notice[1] in 21.02, disable targets with 32M of RAM [1] https://openwrt.org/supported_devices/864_warning Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ath79: fix 5GHz on QCA9886 variant of ZTE MF286Lech Perczak2023-05-20
| | | | | | | | | | | Recently, a strange variant of ZTE MF286 was discovered, having QCA9886 radio instead of QCA9882 - like MF286A, but having MF286 flash layout and rest of hardware. To support both variants in one image, bind calibration data at offset 0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so ath10k can load caldata for both at runtime. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: Add support for D-Link DIR-869-A1Jan Forman2023-05-20
| | | | | | | | | | | | | | | | | | | | Specifications The D-Link EXO AC1750 (DIR-869) router released in 2016. It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash. 10/100/1000 Gigabit Ethernet WAN port Four 10/100/1000 Gigabit Ethernet LAN ports Power Button, Reset Button, WPS Button, Mode Switch Flashing 1. Upload factory.bin via D-link web interface (Management/Upgrade). Revert to stock Upload original firmware via OpenWrt sysupgrade interface. Debricking D-Link Recovery GUI (192.168.0.1) Signed-off-by: Jan Forman <forman.jan96@gmail.com>
* nu801: add kmod-leds-uleds to MR26 + MR18Christian Lamparter2023-05-18
| | | | | | | | | | | | | | support for MR18 and MR26 was developped before the userspace nu801 was integrated with x86's MX100 into OpenWrt. The initial nu801 + kmod-leds-uleds caused build-bot errors. The solution that worked for the MX100 was to include the kmod-leds-uleds to the device platform module. Thankfully, the MR26 and MR18 can just add the uleds package to the DEVICE_PACKAGES variable. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for MikroTik RB951Ui-2HnDMichał Kępień2023-05-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951Ui-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit d19b868b12 ("ar71xx: Add support for MikroTik RB951Ui-2HnD"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8229 switch, 5x 10/100 Mbit/s - 1x PoE in (port 1, 8-30 V input) - 1x PoE out (port 5, 500 mA output) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 9x LED: - 1x power (green, not configurable) - 1x user (green) - 5x FE ports (green) - 1x wireless (green) - 1x PoE out (red) - 1x button (restart) See https://mikrotik.com/product/RB951Ui-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* ath79: mikrotik: bump compat version for yafut imagesThibaut VARÈNE2023-05-15
| | | | | | | | | | | | | | | | | | | | | | | Following 5264296, Mirotik NAND devices now use yafut to flash the kernel on devices. This method is incompatible with the old-style "kernel2minor" flash mechanism. Even though NAND images were disabled in default build since 21.02, a user flashing a new-style image onto an old-style image would result in in a soft-brick[1]. In order to prevent such accidental mishap, especially as these device images will be reenabled in the upcoming release, bump the compat version. After the new image is flashed, the compat version can be updated: uci set system.@system[0].compat_version='1.1' uci commit [1] https://github.com/openwrt/openwrt/pull/12225#issuecomment-1517529262 Cc: Michał Kępień <openwrt@kempniu.pl> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ath79: add Cisco Meraki MR18Christian Lamparter2023-05-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz RAM: 2x Winbond W9751G6KB-25 (128 MiB) FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB) WIFI1: Atheros AR9550 5.0GHz (SoC) WIFI2: Atheros AR9582-AR1A 2.4GHz WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN) LED: 1x Power-LED, 1 x RGB Tricolor-LED INPUT: One Reset Button UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8 (VCC, RX, TX, GND - VCC is closest to the boot set jumper under the console pins.) Flashing instructions: Depending on the installed firmware, there are vastly different methods to flash a MR18. These have been documented on: <https://openwrt.org/toh/meraki/mr18> Tip: Use an initramfs from a previous release and then use sysupgrade to get to the later releases. This is because the initramfs can no longer be built by the build-bots due to its size (>8 MiB). Note on that: Upgrades from AR71XX releases are possible, but they will require the force sysupgrade option ( -F ). Please backup your MR18's configuration before starting the update. The reason here is that a lot of development happend since AR71XX got removed, so I do advise to use the ( -n ) option for sysupgrade as well. This will cause the device to drop the old AR71xx configuration and make a new configurations from scratch. Note on LEDs: The LEDs has changed since AR71XX. The white LED is now used during the boot and when upgrading instead of the green tricolor LED. The technical reason is that currently the RGB-LED is brought up later by a userspace daemon. (added warning note about odm-caldata partition. remove initramfs - it's too big to be built by the bots. MerakiNAND -> meraki-header. sort nu801's targets) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* Revert "ath79: add empty squashfs-lzma filesystem"Daniel Golle2023-05-12
| | | | | | | | | | This reverts commit 91e3419a33f3f0baa2fb25680f5c9a7b2240102b. Now that squashfs3-lzma generates reproducible output we can drop the empty binary. Having a binary file in the tree is not nice and we actually also use squashfs3-lzma for devices which expect the kernel to be loaded from a squashfs3... Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add empty squashfs-lzma filesystemPaul Spooren2023-05-08
| | | | | | | | | | | | | | | | | The filesystem is currently created on every build to trick the boot loader of some FRITZ! devices into accepting the image. Sadly the resulting squashfs-lzma filesystem is not reproducible. To fix this, create a squashfs filesystem once and include it into the repository. Creation happend as shown below rm -rf empty_dir mkdir empty_dir ./staging_dir/host/bin/mksquashfs-lzma \ empty_dir/ empty-squashfs-lzma \ -noappend -root-owned -be -nopad -b 65536 -fixed-time 0 Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: add support for ZTE MF282Andreas Böhler2023-05-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF282 is a LTE router used (exclusively?) by the network operator "3". Specifications ============== SoC: QCA9563 (775MHz) RAM: 128MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 1x GBit LAN LTE: ZTE MF270 (Cat4), detected as P685M WiFi: QCA9880ac + QCA9560bgn MAC addresses ============= LAN: from config WiFi 1: from config WiFi 2: +1 Installation ============ TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download. Once booted, transfer the sysupgrade image and run sysupgrade. LTE Modem ========= The LTE modem is probably the same as in the MF283+, all instructions apply. Configuring the connection using modemmanager works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at>
Powered by cgit, Themed by Ted Yin.