aboutsummaryrefslogtreecommitdiff
path: root/package
Commit message (Collapse)AuthorAge
* ipq4019: add support for ZTE MF287+ aka DreiNeoAndreas Böhler2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* arm-trusted-firmware-rockchip: Update to 2.9Tianling Shen2023-06-25
| | | | | | Switch to standard TF-A build. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: Add support for MOXA AWK-1137CMaximilian Martin2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 * 128 MB of RAM * 16 MB of SPI NOR flash * 2x 10/100 Mbps Ethernet * 2T2R 2.4/5 GHz Wi-Fi * 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * 2x fast ethernet - lan1 + builtin switch port 1 + used as WAN interface - lan2 + builtin switch port 2 + used as LAN interface * 9-30V DC * external antennas Flashing instructions: ====================== Log in to https://192.168.127.253/ Username: admin Password: moxa Open Maintenance > Firmware Upgrade and install the factory image. Serial console access: ====================== Connect a RS232-USB converter to the maintenance port. Pinout: (reset button left) [GND] [NC] [RX] [TX] Firmware Recovery: ================== When the WLAN and SYS LEDs are flashing, the device is in recovery mode. Serial console access is required to proceed with recovery. Download the original image from MOXA and rename it to 'awk-1137c.rom'. Set up a TFTP server at 192.168.127.1 and connect to a lan port. Follow the instructions on the serial console to start the recovery. Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
* mediatek: add support for Mercusys MR90X v1Mikhail Zhilkin2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Mercusys MR90X(EU) v1 router. Device specification -------------------- SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit RAM: MediaTek MT7986BLA (512MB) Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2) WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4 WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4 LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs on ethernet ports Button: 1 (Reset) USB ports: No Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART) --------------------- V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect The R3 (TX line) and R6 (RX line) are absent on the PCB. You should solder them or solder the jumpers. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Once inside OpenWrt, set / update env variables: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Installation (without UART) --------------------------- 1. Login as root via SSH (router IP, port 20001, password - your web interface password) 2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and SSH settings from the p.1) 3. Add a newline after "#!/bin/sh": telnetd -l /bin/login.sh 4. Save "65-iptv" file 5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and save 6. Make sure that telnetd is running: netstat -ltunp | grep 23 7. Login via telnet to router IP, port 23 (no username and password are required) 8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the router (e.g., using WinSCP and SSH settings from the p.1) 9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to download and upload the full version of busybox to the router. For example, from here: https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64 Upload busybox-arm64 to the /tmp dir of the router and run: in the telnet shell: cd /tmp chmod a+x busybox-arm64 10. Check "initramfs-kernel.bin" size: du -h initramfs-kernel.bin 11. Delete old and create new "kernel" volume with appropriate size (greater than "initramfs-kernel.bin" size): ubirmvol /dev/ubi0 -N kernel ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB 12. Write OpenWrt "initramfs-kernel.bin" to the flash: ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin 13. u-boot-env can be empty so lets create it (or overwrite it if it already exists) with the necessary values: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 14. Reboot to OpenWrt initramfs: reboot 15. Login as root via SSH (IP 192.168.1.1, port 22) 16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router 17. Run sysupgrade: sysupgrade -n /tmp/sysupgrade.bin Recovery -------- 1. Press Reset button and power on the router 2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and upload the OEM firmware Recovery (UART) --------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Do what you need (restore partitions from a backup, install OpenWrt etc.) Stock layout ------------ 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" ubi0/ubi1 format ---------------- U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 00:eb:xx:xx:xx:be | label | | LAN | 00:eb:xx:xx:xx:be | label | | WAN | 00:eb:xx:xx:xx:bf | label+1 | | WLAN 2g | 00:eb:xx:xx:xx:be | label | | WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". OEM wireless eeprom is also there (file "MT7986_EEPROM.bin"). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* odhcpd: bump to latest git HEADChristian Marangi2023-06-24
| | | | | | | 5211264 odhcpd: add support for dhcpv6_pd_min_len parameter c6bff6f router: Add PREF64 (RFC 8781) support Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mt76: update to the latest versionFelix Fietkau2023-06-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2c9c8ffe9d8c wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll 3365c80f4202 wifi: mt76: connac: fix stats->tx_bytes calculation b69d82130b47 wifi: mt76: connac: do not check WED status for non-mmio devices 1f9cd65b55d7 wifi: mt76: mt7921e: fix probe timeout after reboot 42dace9ce247 wifi: mt76: mt7921: Fix use-after-free in fw features query. 540adbb38205 wifi: mt76: mt7921: add Netgear AXE3000 (A8000) support 150e2d0ffc0c wifi: mt76: mt7996: fix possible NULL pointer dereference in mt7996_mac_write_txwi() 5b7519be2bf6 wifi: mt76: mt7996: fix endianness of MT_TXD6_TX_RATE 40f6e433f747 wifi: mt76: mt76x02: remove WEP support 84ea1a24f5b5 mt76: mt7921: don't assume adequate headroom for SDIO headers 5c28e17f8c78 wifi: mt76: mt7996: fix header translation logic 2386cec860fa wifi: mt76: mt7996: enable BSS_CHANGED_MU_GROUPS support 748d4a2bfebd wifi: mt76: mt7615: enable BSS_CHANGED_MU_GROUPS support 458ad0af21be wifi: mt76: enable UNII-4 channel 177 support 7fb046011293 wifi: mt76: mt7915: fix background radar event being blocked d2a77a9954bb wifi: mt76: mt7915: report tx retries/failed counts for non-WED path f76b102b09ca wifi: mt76: mt7915: rework tx packets counting when WED is active 5637d9e37d9e wifi: mt76: mt7915: rework tx bytes counting when WED is active 34bdc7fcb4c0 wifi: mt76: report non-binding skb tx rate when WED is active d71aa7b992a3 wifi: mt76: mt7915: drop return in mt7915_sta_statistics 251c363c3087 wifi: mt76: mt7996: drop return in mt7996_sta_statistics 150bb95cb153 wifi: mt76: mt7921: do not support one stream on secondary antenna only d480c3281f21 wifi: mt76: mt7921: remove macro duplication in regs.h 18b1027e5b6e wifi: mt76: mt7915: move mib_stats structure in mt76.h 25ec4b91020e wifi: mt76: mt7996: rely on mib_stats shared definition 6541afa88b3b wifi: mt76: mt7921: rely on mib_stats shared definition eeb60eb9a5a0 wifi: mt76: mt7915: add support for MT7981 [sync with upstream] d5b7e6a3d735 wifi: mt76: mt7921e: report tx retries/failed counts in tx free event f0f19cea6646 wifi: mt76: mt7921: fix skb leak by txs missing in AMSDU edd8a830f6e3 wifi: mt76: add tx_nss histogram to ethtool stats e48235308b3e wifi: mt76: mt7915: accumulate mu-mimo ofdma muru stats a729242363d9 wifi: mt76: mt7921: fix non-PSC channel scan fail 8d52436ee0cd wifi: mt76: mt7921: Support temp sensor d152c8688c14 wifi: mt76: mt7915: disable WFDMA Tx/Rx during SER recovery d07785c344ac wifi: mt76: mt7996: disable WFDMA Tx/Rx during SER recovery 2a19784137f9 wifi: mt76: mt7921: make mt7921_mac_sta_poll static da8e33a15e71 wifi: mt76: mt7915: fix command timeout in AP stop period cc58d5c4a9c9 mt76: mt7996: rely on mt76_sta_stats in mt76_wcid 98a37c82a373 wifi: mt76: mt7921: get rid of MT7921_RESET_TIMEOUT marco ece724cf562b wifi: mt76: mt7996: move radio ctrl commands to proper functions 527cbbc5ede7 wifi: mt76: connac: add support for dsp firmware download 44e323340637 wifi: mt76: mt7996: fix bss wlan_idx when sending bss_info command 63f0053df07a wifi: mt76: mt7996: enable VHT extended NSS BW feature e1bb4ef7b2bb wifi: mt76: connac: add support to set ifs time by mcu command 080ca19cc686 wifi: mt76: mt7996: use correct phy for background radar event 2c163f1812a3 wifi: mt76: mt7996: fix WA event ring size b511a437ace4 wifi: mt76: mt7996: add muru support ece67c98dc1c wifi: mt76: mt7996: increase tx token size 7c2515d85117 wifi: mt76: mt7921e: fix init command fail with enabled device 30706095c566 wifi: mt76: mt7915: move sta_poll_list and sta_poll_lock in mt76_dev b06ed10ee271 wifi: mt76: mt7603: rely on shared sta_poll_list and sta_poll_lock b59bdae339de wifi: mt76: mt7615: rely on shared sta_poll_list and sta_poll_lock 6da2e0e4ef54 wifi: mt76: mt7996: rely on shared sta_poll_list and sta_poll_lock b19d3ad88e8b wifi: mt76: mt7921: rely on shared sta_poll_list and sta_poll_lock 595b033275a3 wifi: mt76: mt7915: move poll_list in mt76_wcid 16fcad171849 wifi: mt76: mt7603: rely on shared poll_list field e19f84091d2e wifi: mt76: mt7615: rely on shared poll_list field b87e4dad1e84 wifi: mt76: mt7996: rely on shared poll_list field 6d7950e258d0 wifi: mt76: mt7921: rely on shared poll_list field f5c5eece5038 wifi: mt76: move ampdu_state in mt76_wcid 7e44467469fe mt76: connac: move more mt7921/mt7915 mac shared code in connac lib 39a70710ddcd wifi: mt76: move rate info in mt76_vif 0dc4326991df wifi: mt76: connac: move connac3 definitions in mt76_connac3_mac.h 29cfabbb4b90 wifi: mt76: connac: add connac3 mac library Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netfilter: fix typo in nf-socket and nf-tproxy kconfigChristian Marangi2023-06-23
| | | | | | | | Fix a typo where the wrong KCONFIG was used and fix selecting the correct kernel config option to use these packages. Fixes: 4f443c885ded ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mac80211: fix quilt patch corruptionFelix Fietkau2023-06-23
| | | | | Fixes: 9219b0660a91 ("mac80211: fix HE issues with AP_VLAN interfaces") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix HE issues with AP_VLAN interfacesFelix Fietkau2023-06-23
| | | | | | Fixes issues with aggregation Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: update to the latest versionFelix Fietkau2023-06-23
| | | | | | | | 1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices b719f189f243 bridge: make hotplug-added vlans default to tagged edf3aced9f9a bridge: add support for adding vlan ranges via hotplug Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: always use mac80211 loss detectionDavid Bauer2023-06-23
| | | | | | | | | | | | ath10k does not report excessive loss in case of broken block-ack sessions. The loss is communicated to the host-os, but ath10k does not trigger a low-ack events by itself. The mac80211 framework for loss detection however detects this circumstance well in case of ath10k. So use it regardless of ath10k's own loss detection mechanism. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Aruba AP-115David Bauer2023-06-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU Qualcomm Atheros QCA9558 RAM 256MB DDR2 FLASH 2x 16M SPI-NOR (Macronix MX25L12805D) WIFI Qualcomm Atheros QCA9558 Atheros AR9590 Installation ============ 1. Attach to the serial console of the AP-105. Interrupt autoboot and change the U-Boot env. $ setenv rb_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; netget 0x80060000 ap115.bin; go 0x80060000" $ setenv fb_openwrt "bank 1; cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000" $ setenv bootcmd "run fb_openwrt" $ saveenv 2. Load the OpenWrt initramfs image on the device using TFTP. Place the initramfs image as "ap105.bin" in the TFTP server root directory, connect it to the AP and make the server reachable at 192.168.1.66/24. $ run rb_openwrt 3. Once OpenWrt booted, transfer the sysupgrade image to the device using scp and use sysupgrade to install the firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* netifd: update to the latest versionFelix Fietkau2023-06-22
| | | | | | | 077e05f2b129 vlan/vlandev: pass through extra vlan information passed via hotplug 40fad91eb5be wireless: add network_vlan config attribute Signed-off-by: Felix Fietkau <nbd@nbd.name>
* filogic: add support for Netgear WAX220Flole Systems2023-06-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: MediaTek MT7986 RAM: 1024MB DDR3 FLASH: 128MB SPI-NAND (Winbond) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect the TFTP server to the WAX220. Conect to the serial console, interrupt the autoboot process by pressing '0' when prompted. 3. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.2.1 $ setenv serverip 192.168.2.2 $ tftpboot openwrt.bin $ bootm 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Signed-off-by: Flole Systems <flole@flole.de> Signed-off-by: Stefan Agner <stefan@agner.ch>
* qualcommax: move ipq807x support to subtargetRobert Marko2023-06-16
| | | | | | | | | | | | Now that qualcommax exists as a target and dependencies have been updated let move ipq807x support to subtarget of qualcommax. This is mostly copy/paste with the exception of having to update SSDK and NSS-DP to use CONFIG_TARGET_SUBTARGET. This is a preparation for later addition of IPQ60xx and IPQ50xx support. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq807x: rename target to qualcommaxRobert Marko2023-06-16
| | | | | | | | | | | | | Currently, ipq807x only covers Qualcomm IPQ807x SoC-s. However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid duplicating kernel patches and everything lets make a common target with per SoC subtargets. Start doing that by renaming ipq807x to qualcommax so that dependencies on ipq807x target can be updated. Signed-off-by: Robert Marko <robimarko@gmail.com>
* hostapd: add UCI option for Multiple BSSIDStijn Tintel2023-06-16
| | | | | | | | | | | | | | | Add an UCI option to enable Multiple BSSID Advertisement. Enabling this will announce all BSSIDS on a phy in a single beacon frame. The interface that is brought up first will be the transmitting profile, all others are non-transmitting profiles and will be advertised in the Multiple BSSID element in Beacon and Probe Response frames of the first interface. This depends on driver and client support. Enabling this will result in all but the first interface not being visible at all for clients that do not support it. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* base-files: upgrade: nand: add JFFS2 cleanmarkers supportÁlvaro Fernández Rojas2023-06-15
| | | | | | | | Some Broadcom MIPS devices require JFFS2 cleanmarkers to be present on the kernel partition or the bootloader will identify the partition as corrupt and won't boot the kernel. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* openssl: passing cflags to configureJitao Lu2023-06-14
| | | | | | | | openssl sets additional cflags in its configuration script. We need to make it aware of our custom cflags to avoid adding conflicting cflags. Fixes: #12866 Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
* ppp: backport patches improving ppp interface creationChristian Marangi2023-06-14
| | | | | | | | | Backport patches improving ppp interface creation. As a side effect this also fix a bug from using netdev trigger that suffer from LED state wrongly set due to using old ioctl for ppp creation. Tested-by: Csaba Sipos <metro4@freemail.hu> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* restool: update source.codeaurora.org repository linkChristian Marangi2023-06-11
| | | | | | | | source.codeaurora.org project has been shut down and the nxp repositories has been moved to github. Update the repository link to the new location. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ls-dpl: update source.codeaurora.org repository linkChristian Marangi2023-06-11
| | | | | | | | source.codeaurora.org project has been shut down and the nxp repositories has been moved to github. Update the repository link to the new location. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* uqmi: do not start 464xlat for dual-stack configurationsLech Perczak2023-06-11
| | | | | | | | If dual-stack configuration is in use, and dhcpv6 option is set, do not start 464xlat sub-interface for dhcpv6 sub-interace , as the configuration already provides IPv4 connectivty, be it through single or dual APN configuration. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* uqmi: support split-APN IPv4 and IPv6 dual-stackLech Perczak2023-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add two new "v6apn" and "v6profile" properties, to support split-APN dual-stack onfiguration. This extends the existing ipv4v6 PDP type, allowing simultaneous connection to two distinct APNs, one for IPv4 and one for IPv6. The parameters override existing 'apn' and 'profile' respectively, if set, but only for IPv6 part of the connection. If unset, they default to their original values, constituting a standard IPv4v6 setup. If a different APN is set for IPv6, a corresponding profile MUST also be configured, with a different ID, than the IPv4 profile, for example, profile 2. Both APNs must match ones configured through QMI or through 'AT+CGDCONT' command. Example configuration in UCI: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option autoconnect '1' option pdptype 'ipv4v6' option apn 'internet' option v6apn 'internetipv6' option profile '1' option v6profile '2' Corresponding profile configuration: AT+CGDCONT? +CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0 +CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0 Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* swconfig: fix memory leak when cli call swlib_get_attr()nichel Chen2023-06-11
| | | | | | | The cli is a one-time run, and memory leaks would have been irrelevant. But people call libsw with cli programs as samples. Doing a good job of memory management calls means that people who call libsw are not so easy to make mistakes. Signed-off-by: nichel Chen <nichelnich@gmail.com>
* ramips: Add support for Beeline SmartBox TURBO+Maximilian Weinmann2023-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router. Device specification -------------------- SoC Type: MediaTek MT7621AT (880 MHz, 2 cores) RAM (Nanya NT5CC64M16GP): 128 MiB Flash (Macronix MX30LF1G18AC): 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615N): a/n/ac, 4x4 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) USB ports: 1xUSB3.0 Buttons: 2 button (reset, wps) LEDs: Red, Green, Blue Zigbee (EFR32MG1B232GG): 3.0 Stock bootloader: U-Boot 1.1.3 Power: 12 VDC, 1.5 A Installation (fw 2.0.9) ----------------------- 1. Login to the web interface under SuperUser (root) credentials. Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the device written on the backplate stick. 2. Navigate to Setting -> WAN. Add: Name - WAN1 Connection Type - Static IP Address - 172.16.0.1 Netmask - 255.255.255.0 Save -> Apply. Set default: WAN1 3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add: Protocol - SSH Port - 22 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN Interface - WAN1 Save ->Apply Add: Protocol - HTTP Port - 80 IP Address - 172.16.0.1 Netmask - 255.255.255.0 WAN interface - WAN1 Save -> Apply 4. Set up your PC ethernet: Connection Type - Static IP Address - 172.16.0.2 Netmask - 255.255.255.0 Gateway - 172.16.0.1 5. Connect PC using ethernet cable to the WAN port of the router 6. Connect to the router using SSH shell under SuperUser account 7. Make a mtd backup (optional, see related section) 8. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 9. Login to the router web interface under admin account 10. Remove dots from the OpenWrt factory image filename 11. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 171.16.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses (fw 2.0.9) ------------------------ +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:e8 | | WAN | label + 1 | *:e9 | | 2g | label + 4 | *:ec | | 5g | label + 5 | *:ed | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 Factory image format -------------------- +---+-------------------+-------------+--------------------+ | # | Offset | Size | Description | +---+-------------------+-------------+--------------------+ | 1 | 0x0 | 0x200 | Tag Header Factory | | 2 | 0x200 | 0x100 | Tag Header Kernel1 | | 3 | 0x300 | 0x100 | Tag Header Kernel2 | | 4 | 0x400 | SIZE_KERNEL | Kernel | | 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) | +---+-------------------+-------------+--------------------+ Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com> Signed-off-by: Maximilian Weinmann <x1@disroot.org>
* uboot-armsr: add support for QEMU armv7/armv8Petr Štetiar2023-06-10
| | | | | | | | | | | Add new package so we can use self-compiled bootloader during QEMU based testing and development. Backported fix[1] is needed for EFI boot from virtio devices. 1. https://patchwork.ozlabs.org/project/uboot/patch/20230424134946.v10.7.Ia5f5e39c882ac22b5f71c4d576941b34e868eeba@changeid/ Signed-off-by: Petr Štetiar <ynezz@true.cz>
* wolfssl: change armvirt reference to armsrMathew McBride2023-06-10
| | | | | | armvirt target has been renamed to armsr (Arm SystemReady). Signed-off-by: Mathew McBride <matt@traverse.com.au>
* kernel: netdevices: change armvirt references to armsrMathew McBride2023-06-10
| | | | | | armvirt target has been renamed to armsr (Arm SystemReady) Signed-off-by: Mathew McBride <matt@traverse.com.au>
* grub2: change armvirt reference to armsrMathew McBride2023-06-10
| | | | | | | The armvirt target has been renamed to armsr (Arm SystemReady), so the GRUB configuration also needs to change. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* ipq807x: add initial support for prpl Foundation Haze boardPetr Štetiar2023-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Haze is prpl Foundation's reference board (WNC LVRP). Board info: - IPQ8072A SoC - 2 GiB RAM - 4 GiB eMMC - 8MiB SPI NOR (MX25U6435F) - 3x 1GigE ports (QCA8075) - 1x 10GigE port (AQR113C) - 1x SFP cage - WiFi 6GHz 160MHz (QCN9074) - WiFi 5GHz 80+80MHz (QCN5054) - WiFi 2.4G (QCN5024) - ARM Standard 20-pin 2.54mm/0.1" JTAG (1V8 !!!) - Bluetooth v5.0 + EDR with integrated Class 1 PA (CYW20704) - 1x M.2 B-key socket with PCIe 3.0 - 1x USB 3.0 port - UART marked J6 is 4-pin 2.54mm/0.1" connector 3V3(arrow),RX,TX,GND (115200 8N1) - Reset and WPS buttons Flashing instructions: 1. From U-Boot boot OpenWrt using initramfs image: IPQ807x# tftpboot openwrt-ipq807x-generic-prpl_haze-initramfs-uImage.itb && bootm 2. In OpenWrt running from initramfs execute sysupgrade: root@OpenWrt:/# sysupgrade -n /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin Work in progress/known issues: * SFP feature not implemented/tested * M.2 feature not implemented/tested * Bluetooth feature not implemented/tested * 6GHz wireless should be working, but not tested * MAC address assigments for LAN interfaces Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq-wifi: update to version 2023-06-03Petr Štetiar2023-06-10
| | | | | | | | | | | | | Contains following updates: * ipq8074: update RegDB in new submitted BDF * Revert "ipq8074: update RegDB in new submitted BDF" * qcn9074: update RegDB in new submitted BDF * ipq8074: update RegDB in new submitted BDF * qca-wireless: ipq40xx: add BDFs for ZTE MF287+ * Add BDFs for prpl Foundation Haze board Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: qca-ssdk: renumber patchesRobert Marko2023-06-10
| | | | | | Lets reexport the patches in order to have them renumbered from 0 again. Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: qca-ssdk: drop 5.15 supportRobert Marko2023-06-10
| | | | | | | There is no need for SSDK to support 5.15 anymore since the only user and possible future ones are on 6.1. Signed-off-by: Robert Marko <robimarko@gmail.com>
* uboot-envtools: Add u-boot env config for GL-MT3000Jianhui Zhao2023-06-09
| | | | | | | | This commit add u-boot env config for GL-MT3000, so that we can use fw_printenv to print u-boot env and use fw_setenv to set u-boot env in GL-MT3000. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
* kernel: modules: fix mdio-bus-mux descriptionLuiz Angelo Daros de Luca2023-06-09
| | | | | | | Simple error during copy/paste Fixes: 2dbeb607251b ("kernel: add mdio-bus-mux support") Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* openssl: update to 3.0.9Ivan Pavlov2023-06-09
| | | | | | | | | | | | | | CVE-2023-2650 fix Remove upstreamed patches Major changes between OpenSSL 3.0.8 and OpenSSL 3.0.9 [30 May 2023] * Mitigate for very slow OBJ_obj2txt() performance with gigantic OBJECT IDENTIFIER sub-identities. (CVE-2023-2650) * Fixed buffer overread in AES-XTS decryption on ARM 64 bit platforms (CVE-2023-1255) * Fixed documentation of X509_VERIFY_PARAM_add0_policy() (CVE-2023-0466) * Fixed handling of invalid certificate policies in leaf certificates (CVE-2023-0465) * Limited the number of nodes created in a policy tree (CVE-2023-0464) Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
* kernel: ltq-ptm: do not write directly to dev->addrAleksander Jan Bajkowski2023-06-06
| | | | | | | | | | One is never to write to dev->addr directly. In 6.1 it will be a const and with the newly enabled WERROR, we get a failing grade. Lets fix this ahead of time. Ref: https://github.com/torvalds/linux/commit/adeef3e32146a8d2a73c399dc6f5d76a449131b1 Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* uboot-mediatek: adapt BPi-R3 and BPi-R64 to new device tree overlayDaniel Golle2023-06-05
| | | | | | | | Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new device tree overlay mechanism now that support for multiple device tree overlays has been added. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "ipq807x: add initial support for prpl Foundation Haze board"Petr Štetiar2023-06-05
| | | | | | | This reverts commit 48603a271e6ff9e5cd851e873429893115e00c94 as this was commited by accident, its still work in progress. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "ipq-wifi: add board files for prpl Foundation Haze board"Petr Štetiar2023-06-05
| | | | | | | This reverts commit 6845c53ec3bb25dbbb0e8bbcf435fc380502fc56. as this was commited by accident, its still work in progress. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "WIP: ipq-wifi: use my fork temporarily until upstreamed"Petr Štetiar2023-06-05
| | | | | | | This reverts commit 1bad93c42669061b0248ca5cff1d83e399a2ef1a as this was commited by accident, its still work in progress. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "ath11k-firmware: update to WLAN.HK.2.9.0.1-01713-QCAHKSWPL_SILICONZ-1"Robert Marko2023-06-05
| | | | | | | | | | | This reverts commit 5d2de0055504727503a050731c3ca8c75b51f185. I received multiple reports that in various configurations this FW version is not stable and crashes, so lets revert to 01385 revision which works. Fixes #12815 Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixes tag]
* WIP: ipq-wifi: use my fork temporarily until upstreamedPetr Štetiar2023-06-05
| | | | Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq-wifi: add board files for prpl Foundation Haze boardPetr Štetiar2023-06-05
| | | | | | | | | | | | QSDK based factory firmware was setting following board_ids in DTS: ath11k_pci 0001:01:00.0: chip_id 0x0 chip_family 0x0 board_id 0xa4 soc_id 0xffffffff ath11k c000000.wifi1: chip_id 0x0 chip_family 0x0 board_id 0x294 soc_id 0xffffffff Thus board-prpl_haze.qcn9074` was extracted from `bus=...qmi-board-id=164.bin` file and `board-prpl_haze.ipq8074` from `bus=...qmi-board-id=660.bin` file. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq807x: add initial support for prpl Foundation Haze boardPetr Štetiar2023-06-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Haze is prpl Foundation's reference board (WNC LVRP). Board info: - IPQ8072A SoC - 2 GiB RAM - 4 GiB eMMC - 8MiB SPI NOR (MX25U6435F) - 3x 1GigE ports (QCA8075) - 1x 10GigE port (AQR113C) - 1x SFP cage - WiFi 6GHz 160MHz (QCN9074) - WiFi 5GHz 80+80MHz (QCN5054) - WiFi 2.4G (QCN5024) - ARM Standard 20-pin 2.54mm/0.1" JTAG (1V8 !!!) - Bluetooth v5.0 + EDR with integrated Class 1 PA (CYW20704) - 1x M.2 B-key socket with PCIe 3.0 - 1x USB 3.0 port - UART 4-pin 3V3(arrow),RX,TX,GND (115200 8N1) - Reset and WPS buttons Flashing instructions: 1. From U-Boot boot OpenWrt using initramfs image: IPQ807x# tftpboot openwrt-ipq807x-generic-prpl_haze-initramfs-uImage.itb && bootm 2. In OpenWrt running from initramfs execute sysupgrade: root@OpenWrt:/# sysupgrade -n /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin Work in progress/known issues: * SFP feature not implemented/tested * M.2 feature not implemented/tested * Bluetooth feature not implemented/tested * 6GHz wireless should be working, but not tested * MAC address assigments for LAN interfaces Signed-off-by: Petr Štetiar <ynezz@true.cz>
* qca-nss-dp: fix oops in nss_dp_probePetr Štetiar2023-06-05
| | | | | | | | | | | | | | | | | | | Currently kernel crashes when of_phy_connect has issues: Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000308 ... pc : phy_attached_print+0x28/0x1b0 lr : phy_attached_info+0x14/0x20 ... Call trace: phy_attached_print+0x28/0x1b0 phy_attached_info+0x14/0x20 nss_dp_adjust_link+0x544/0x6c4 [qca_nss_dp] of_phy_connect returns either pointer or NULL, so can't be checked with IS_ERR macro. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* libubox: update to the latest versionFelix Fietkau2023-06-04
| | | | | | | | | | | | b09b316aeaf6 blobmsg: add blobmsg_parse_attr function eac92a4d5d82 blobmsg: add blobmsg_parse_array_attr ef5e8e38bd38 usock: fix poll return code check 6fc29d1c4292 jshn.sh: Add pretty-printing to json_dump 5893cf78da40 blobmsg: Don't do at run-time what can be done at compile-time 362951a2d96e uloop: fix uloop_run_timeout 75a3b870cace uloop: add support for integrating with a different event loop Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: update to the latest versionFelix Fietkau2023-06-04
| | | | | | ec9dba721245 system-linux: fix memory leak in system_bridge_vlan_check Signed-off-by: Felix Fietkau <nbd@nbd.name>
* unetd: update to the latest versionFelix Fietkau2023-06-04
| | | | | | | | | | | 412d03012f13 network: prevent adding endpoint routes for addresses on the network faaf9cee6ef4 utils: fix ipv4 checksum issue 0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init 51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips 7d3986b7a5a2 wg-linux: increase default messages size Signed-off-by: Felix Fietkau <nbd@nbd.name>
Powered by cgit, Themed by Ted Yin.