aboutsummaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAge
...
* rockchip: add NanoPi R5S supportTianling Shen2023-11-26
| | | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3568 ARM64 (4 cores) 2GB or 4GB LPDDR4X RAM 1x 1000 Base-T 2x 2500 Base-T 4 LEDs (LAN1 / LAN2 / WAN / POWER) 8GB eMMC on-board Micro-SD Slot M.2 Slot 2x USB 3.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Tested-by: Packet Please <pktpls@systemli.org> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: add NanoPi R5S supportTianling Shen2023-11-26
| | | | | | | Add support for the FriendlyARM NanoPi R5S support. Tested-by: Packet Please <pktpls@systemli.org> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: armv8: broaden boardnameTianling Shen2023-11-26
| | | | | | Now we have rk356x support :-) Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: enable drivers for rk356xTianling Shen2023-11-26
| | | | | | | Enable all necessary drivers for the rk356x SoCs, including PHY, SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: remove kernel 5.15 patches and configTianling Shen2023-11-26
| | | | | | As we switched to kernel 6.1, these files can go. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: switch to kernel 6.1Tianling Shen2023-11-26
| | | | | | Required by the following rk3568 support. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: move image generation command to defaultTianling Shen2023-11-26
| | | | | | | | It's applicable for all devices so move it to default to reduce redudant code. Addtionally introduce a new variable `BOOT_SCRIPT` to allow custom boot script (if necessary). Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rkbin: add new TF-A package for rk35xxTianling Shen2023-11-26
| | | | | | | Currently there's no usable mainline (open source) TF-A implementation for rk35xx SoCs, so pack the prebuilt firmware from the vendor. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: Update to 2023.07.02Tianling Shen2023-11-26
| | | | | | | | | | | | | | | * Removed swig hacks and prebuilt of-platdata * Removed upstreamed patches - 101-rock64pro-disable-CONFIG_USE_PREBOOT.patch - 102-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R2C.patch * Reordered patches * Introduced new dependencies check * Overrided default PATH to avoid race condition (host python3 vs hostpkg python3) * Switched to use UBOOT_CUSTOMIZE_CONFIG for config update Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-sunxi: use intree dtc explicitlyTianling Shen2023-11-26
| | | | | | This replaces pylibfdt hack. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-sifiveu: use intree dtc explicitlyTianling Shen2023-11-26
| | | | | | This replaces pylibfdt hack. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: use intree dtc explicitlyTianling Shen2023-11-26
| | | | | | This replaces pylibfdt hack. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* u-boot: introduce dependencies check for swig and pyelftoolsTianling Shen2023-11-26
| | | | | | | They are required by modern u-boot builds, e.g. uboot-rockchip and uboot-sunxi. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ipq40xx: enable UBI size checks for some Linksys NAND devicesTony Ambardar2023-11-26
| | | | | | | | Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300, WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved blocks on NAND devices. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* image: improve UBI image sizing on NAND devicesTony Ambardar2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | Many NAND devices use a build recipe with "append-ubi | check-size" to ensure factory images don't exceed the target flash partition size. However, UBI reserves space for bad block handling and other operational overhead, and thus 'check-size' can overestimate the space available by several MB. In practice, this means a failed check is definitely a failure, while a passing check is only probably a pass. Improve the situation by teaching 'Build/append-ubi' to check image sizes while accounting for UBI reserved blocks. Add new device variable NAND_SIZE and use with existing IMAGE_SIZE to derate the available space. Each UBI device reserves 20 PEBs per 1024 PEBs of the entire NAND device for bad blocks, plus an additional 4 PEBs overhead. Many devices can transparently enable this check by setting NAND_SIZE based on their flash storage, and may then remove any unneeded 'check-size'. Link: http://www.linux-mtd.infradead.org/doc/ubi.html#L_overhead Suggested-by: Shiji Yang <yangshiji66@qq.com> Suggested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* image: fix Linksys image alignment and simplify footer creationTony Ambardar2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current factory image sizes for Linksys devices are 256-byte aligned. This is not an issue writing factory images from the OpenWrt or Linksys GUIs, but can lead to failures using a TFTP client from the Linksys bootloader: NAND write: device 1 offset 0x2800000, size 0xc00100 Attempt to write to non page aligned data NAND write to offset 2800000 failed -22 0 bytes written: ERROR Simplify Linksys footer creation by migrating to a makefile build recipe, and pre-pad the footer (with 0xFF) to ensure the final image is $(PAGESIZE) aligned. Finally, remove the old linksys-image.sh script no longer needed. Linksys footer details are given below for future reference. The 256-byte footer is appended to factory images and tested by both the Linksys Upgrader (observed in EA6350v3) and OpenWrt sysupgrade. Footer format: .LINKSYS. Checked by Linksys upgrader before continuing. (9 bytes) <VERSION> Upgrade version number, unchecked so arbitrary. (8 bytes) <TYPE> Model of device, space padded (0x20). (15 bytes) <CRC> CRC checksum of factory image to flash. (8 bytes) <padding> Padding ('0' + 0x20 * 7) (8 bytes) <signature> Signature of signer, unchecked so arbitrary. (16 bytes) <padding> Padding with nulls (0x00) (192 bytes) Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1358510123 Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1587517739 Reported-by: Stijn Segers <foss@volatilesystems.org> Reported-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* image: use helper function for size unitsTony Ambardar2023-11-26
| | | | | | | | Add the make function 'exp_units' for helping evaluate k/m/g size units in expressions, and use this to consistently replace many ad hoc substitutions like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix typo in Linksys WHW01 image definitionTony Ambardar2023-11-26
| | | | | | | | Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit conversions in build recipes (e.g. 75776k -> 75776*1024). Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for D-link DAP-1720 A1Rani Hod2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa <protectivedad@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ath79: ar: convert to mac-baseRosen Penev2023-11-25
| | | | | | Replacement for deprecated mac-address-increment Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: ar: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: tp9343: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows getting rid of deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qcn: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows getting rid of deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qca: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qca: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: mikrotik: fix dts warningsRosen Penev2023-11-25
| | | | | | property has invalid length Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: nix mac-address-incrementRosen Penev2023-11-26
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: add interrupt-controllerRosen Penev2023-11-26
| | | | | | | | Fixes dtc warning: '#interrupt-cells' found, but node is not an interrupt provider Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620a: use mac-baseRosen Penev2023-11-26
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620a: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows using mac-base to replace mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620n: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | nvmem-cells is deprecated. nvmem-layout allows using mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7628: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7628: use nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow using mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: rtxxxx: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | Deprecated and replaced upstream with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: rtxxxx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-adress-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts and image recipes to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* uboot-envtools: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: remove kmod-usb2 for GL-MT6000Chukun Pan2023-11-25
| | | | | | | The usb driver requires kmod-usb3, not kmod-usb2. Remove the useless kmod-usb2 from default package. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: Cetron CT3003: fixes typo for spi propertiesChukun Pan2023-11-25
| | | | | | | Same as commit 3674689, correct 'buswidth' to 'bus-width'. Also move the nmbm properties outside the partition definition. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ipq40xx: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: fix dtc warnimgRosen Penev2023-11-25
| | | | | | I2C bus unit address format error, expected "62" Signed-off-by: Rosen Penev <rosenp@gmail.com>
* qualcommax: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | nvmem-cells is deprecated Signed-off-by: Rosen Penev <rosenp@gmail.com>
* apm821xx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | nvmem-cells is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AXHauke Mehrtens2023-11-25
| | | | | | | The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX Fixes: c8c2f522625c ("mediatek: add support for Zbtlink ZBT-Z8102AX") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mt76x8 add support for RTC class/driversXiaobo Liu2023-11-25
| | | | | | This commit adds support for RTC class/drivers to the mt76x8 target. Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com>
* f2fs-tools: avoid dead symlinks in rootRosen Penev2023-11-25
| | | | | | | When building on the host, this avoids creating dead symlinks. Matches what is done elsewhere. Signed-off-by: Rosen Penev <rosenp@gmail.com>
Powered by cgit, Themed by Ted Yin.