aboutsummaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAge
...
* qualcommax: ipq807x: alphabetically sort Netgear WAX family.Kristian Skramstad2023-10-28
| | | | | | | | | | | | | As requested by the maintainers, the order for the WAX family should be alphabetically. WAX620 is now after WAX218. Files changed: +ipq807x.mk +01_leds No changes to the content. Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* mediatek: add CMCC RAX3000M supportTianling Shen2023-10-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 64GB eMMC or 128 MB SPI-NAND RAM: 512MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A - UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | GND TX VCC RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface, and download the configuration. 2. Enter fakeroot, decompress the configuration: tar -zxf cfg_export_config_file.conf 3. Edit 'etc/config/dropbear', set 'enable' to '1'. 4. Edit 'etc/shadow', update (remove) root password: 'root::19523:0:99999:7:::' 5. Repack 'etc' directory: tar -zcf cfg_export_config_file.conf etc/ * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat', just ignore it. 6. Upload new configuration via web interface, now you can SSH to RAX3000M. Check stroage type: Check the label on the back of the device: "CH EC CMIIT ID: xxxx" is eMMC version "CH CMIIT ID: xxxx" is NAND version eMMC Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'factory' part. ('data' partition can be ignored, it's useless.) 2. Write new GPT table: dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync 3. Erase and write new BL2: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync 4. Erase and write new FIP: dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync 5. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 6. Serve OpenWrt initramfs image using TFTP server. 7. Cut off the power and re-engage, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. 9. Additionally, if you want to have eMMC recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync NAND Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'Factory' part. 2. Erase and write new BL2: mtd erase BL2 mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2 3. Erase and write new FIP: mtd erase FIP mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP 4. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 5. Serve OpenWrt initramfs image using TFTP server. 6. Cut off the power and re-engage, wait for TFTP recovery to complete. 7. After OpenWrt has booted, erase UBI volumes: ubidetach -p /dev/mtd0 ubiformat -y /dev/mtd0 ubiattach -p /dev/mtd0 8. Create new ubootenv volumes: ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB 9. Additionally, if you want to have NAND recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb 10. Perform sysupgrade. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: add support for CMCC RAX3000MTianling Shen2023-10-28
| | | | | | | The OEM U-Boot uses dual boot and signature verification which does not support by OpenWrt. So add a custom U-Boot build for OpenWrt. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* arm-trusted-firmware-mediatek: add emmc/spim-nand ddr4 build for mt7981Tianling Shen2023-10-28
| | | | | | They will be used on CMCC RAX3000M. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* sunxi: enable cpufreq driver for H6 SoCChukun Pan2023-10-28
| | | | | | | Allwinner H6 needs this driver to enable DVFS support. May also be used with H616/H618 SoC in the future. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* sunxi: fixes led for nanopi boardsChukun Pan2023-10-28
| | | | | | | | | | | | Kernel 5.15 already supports the NanoPi R1 and NanoPi R1S H5, and they use new LED bindings that do not match the existing settings in 01_leds. Update led settings to fixes that. List the led node on NanoPi R1S H5: root@OpenWrt:~# ls /sys/class/leds/ green:lan green:wan red:status Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ucode: fix build on macosFelix Fietkau2023-10-28
| | | | | | | Remove ABI version, since its format is not accepted by the linker. Enable rpath to avoid clash with system libraries Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport nvmem v6.6 fixes and v6.7 changesRafał Miłecki2023-10-28
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.15 to 5.15.137John Audia2023-10-27
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.137 All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* ucode: update to latest Git HEADJo-Philipp Wich2023-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Introduces signal handling facilities - Fixes potentially incorrect object equality tests - Introduces debug library - Introduces log library - ABI version bump due to changed VM structure layout - Revised packaging Changelog: 07c0317 jsdoc: switch to own custom theme 6ca08b0 jsdoc: properly handle indented documentation blocks 2a67f22 lib: add/improve documentation for require(), loadfile(), loadstring() 9993ccb uci: fix potential memory leaks in `configs()` f56394f ci: re-trigger workflows on pull request pushes 1c18993 lib: various documentation fixes d25dcb1 uci: add module documentation 4a8ece2 docs: use CSS and local JavaScript fixups to improve formatting 8f21cfa lib: introduce log library 8a3aefe build: auto-enable module depending on present libraries 6a01adc build: convert CMakeLists.txt into lowercase 8700665 ci: don't skip pull request workflows for `master` branch 0184d23 include: fix execvpe compat function on macOS 8b23884 uloop: rename environ variable to avoid clashing with system macro on macOS 7c209d7 types: ensure double serializatiion with decimal places d150425 rtnl: update the link attr TODOs d394174 rtnl: add IFLA_TARGET_NETNSID for operating in other namespaces 1227733 lib: fix documented return value for `splice()` c9982de docs: add struct module documentation 7dde493 docs: add missing headline to debug module documentation 8f852ea types: improve comparison reliability of binary strings 6940c28 lib: introduce debug library be07107 treewide: consolidate platform specific code in platform.c 2593270 uloop: interrupt on VM signals 97a5292 lib: add `signal()` stdlib function 1dbbb6a main: enable signal dispatching in the standalone cli interpreter 1623245 types: treat signal handler array as GC root 29b1c0d vm: introduce basic signal handling infrastructure 093684d fs: explicitly compare isatty() result 4f4f38f types: don't rely on implicit type conversion in ucv_compare() 4bee0ef docs: disable GitHub Jekyll post processing 5efb7a0 docs: further rework 33bc7bf docs: fix markup quirks 9d5e420 docs: add information about memory management and operator precedence f1190ef docs: various improvements f0cc841 fs: use `fseeko()` and `ftello()` cba0c3c fs: complete function documentation coverage f9260f7 github: drop superfluous CNAME file c85bc74 Create CNAME 5309294 lib: add JSDoc documentation b0f2f90 fs: add JSDoc documentation fe086da math: add JSDoc documentation 70f9348 docs: add initial JSDoc infrastructure 24f1a56 source: fix source offset accounting 9df9160 lexer: don't count EOF token as newline b9d8f06 ci: switch to official openwrt/gh-action-sdk Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: usb-audio remove Kconfig USB_AUDIOLiangbin Lian2023-10-26
| | | | | | | | CONFIG_USB_AUDIO is a "USB Audio Gadget" driver, not a usb device driver CONFIG_USB_AUDIO is "USB Audio support" before linux 2.6 Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
* kernel: Enable hwmon for nvmeLuca Barbato2023-10-26
| | | | | | | | | Expose the temperature sensors as hwmon, it improves the overall user experience since on tiny boards the nvme can become a substantial source of heat. Signed-off-by: Luca Barbato <lu_zero@gentoo.org> Reviewed-by: Robert Marko <robimarko@gmail.com>
* kernel: bump 5.15 to 5.15.136John Audia2023-10-26
| | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.136 Removed bcm53xx patch backported from 5.15.136: target/linux/bcm53xx/patches-5.15/081-xhci-Keep-interrupt-disabled-in-initialization-until.patch [1] All other patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 1. https://github.com/openwrt/openwrt/pull/13751#issuecomment-1781206937 Signed-off-by: John Audia <therealgraysky@proton.me> [rmilecki: updated commit description & tested on Luxul XWR-3150] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport XHCI patch modifying xhci_run_finished()Rafał Miłecki2023-10-26
| | | | | | | This will help switching to newer 5.15 kernels. This backport required rebasing Northstar's USB host patch. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: add missed spin unlock to USB host patchRafał Miłecki2023-10-26
| | | | | Fixes: 265071af7c45 ("bcm53xx: add testing support for kernel 6.1") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 6.1 to 6.1.60John Audia2023-10-26
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.60 All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* bcm53xx: backport 1 more late DT patch accepted for v6.7Rafał Miłecki2023-10-26
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* openssl: update to 3.0.12Hauke Mehrtens2023-10-26
| | | | | | | Major changes between OpenSSL 3.0.11 and OpenSSL 3.0.12 [24 Oct 2023] * Mitigate incorrect resize handling for symmetric cipher keys and IVs. (CVE-2023-5363) Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uqmi: update to latest HEADDavid Bauer2023-10-25
| | | | | | | | | c8c9f10 uim: fix help formatting aac0776 uqmi: add APN profile commands ffc5eea uim: support SIM card power-up/down d6c963d uim: add application state to SIM status Signed-off-by: David Bauer <mail@david-bauer.net>
* mtd-utils: update to 2.1.6Nick Hainke2023-10-25
| | | | | | | Release Notes: https://lists.infradead.org/pipermail/linux-mtd/2023-August/100922.html Signed-off-by: Nick Hainke <vincent@systemli.org>
* ixp4xx: Add USRobotics USR8200 supportLinus Walleij2023-10-25
| | | | | | | This brings back USRobotics USR8200 support to the IXP4xx target. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ixp4xx: Add a ixp4xx hardware crypto kernel moduleLinus Walleij2023-10-25
| | | | | | | | The IXP4xx crypto module must be loaded after the rootfs is up as it depends on loading some NPE microcode from the file system. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ixp4xx: Resurrect IXP4xx support using device treeLinus Walleij2023-10-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This resurrects the support for IXP4xx using device tree rather than the old (deleted) board files. The final pieces of IXP4xx board files were deleted in Linux v5.19. Ext4 root filesystems on CF and USB are supported by the default config. We support these three initial targets: - The Gateworks Avila GW2348 reference design has 64MB of RAM and 32MB of flash and also supports USB and CompactFlash. - The Gateworks Cambria GW2358 reference design has 128MB of RAM and 32MB of flash and also supports USB and CompactFlash. - The old and stable Linksys NSLU2 works fine as well, albeit it only has 32MB of RAM so it has been marked as non-default. The 8MB of flash can only fit the kernel, so it has been patched to boot from exteral media on USB. I have used it successfully as a NAS with ksmbd and LUCI web API, see: https://dflund.se/~triad/krad/ixp4xx/ Signed-off-by: Howard Harte <hharte@magicandroidapps.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* firmware: Resurrect the ixp4xx microcode packageLinus Walleij2023-10-25
| | | | | | | | | | | | The firmware package for the IXP4xx microcode was deleted but the source files are still in the file cache so we can easily resurrect it. The firmware either supports ethernet (the most common) or WAN (less common), image targets select the firmware they want depending on usecase. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* generic: Support Altima AMI101L PHYLinus Walleij2023-10-25
| | | | | | | | This is a backport of the patch to support the Altima AMI101L PHY which is merged for the v6.7 kernel. This PHY is used in the IXP4xx-based USRobotics USR8200. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* generic: RTC7301 byte-addressed IOLinus Walleij2023-10-25
| | | | | | | | This is a backport of the patch for byte addressed IO to the Epson RTC7301 driver. This is used by the IXP4xx-based USRobotics USR8200. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* kernel: netdevices: Package AMD PHYLinus Walleij2023-10-25
| | | | | | | This adds a package for the AMD and Altima PHY, found in some odd devices. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* image: Fix the CONFIG_EXTERNAL_CPIO logicLuca Barbato2023-10-24
| | | | | | | | Fix the qstrip call. Fixes: #13776. Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
* sifiveu: remove 5.15 supportZoltan HERPAI2023-10-24
| | | | | | With 6.1 as the default kernel, there is no reason to keep 5.15 around. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sifiveu: switch to kernel v6.1Zoltan HERPAI2023-10-24
| | | | | | Enable kernel v6.1 as the default kernel for sifiveu. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* bcm53xx: disable unused switch ports in downstream patchRafał Miłecki2023-10-24
| | | | | | | | This makes Linux use correct switch ports again. Fixes: a4792d79e899 ("bcm53xx: backport DT changes from v6.5") Fixes: https://github.com/openwrt/openwrt/issues/13548 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport DT changes queued for v6.7Rafał Miłecki2023-10-24
| | | | | | | | Among other changes this commit makes Linux use correct switch ports again. Fixes: a4792d79e899 ("bcm53xx: backport DT changes from v6.5") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: simplify patch adding switch portsRafał Miłecki2023-10-24
| | | | | | | We now have all raw ports defined in bcm-ns.dtsi. Leave only lables in custom device files. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* base-files: functions.sh: Add prepend() homologue to append()Philip Prindeville2023-10-23
| | | | | | | | | | | | | Sometimes it's useful to be able to prepend to a variable as well, such as when dealing with domain names, e.g. prepend fdqn "$subdomain" "." will result in: fqdn="$subdomain.$fqdn" Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* kernel: ath79, bmips: refresh 5.15 patchesMarek Behún2023-10-23
| | | | | | | One LED patch for ath79 and one LED patch for bmips need to be refreshed. Signed-off-by: Marek Behún <kabel@kernel.org>
* kernel: 5.15: Backport Turris Omnia LED patchesMarek Behún2023-10-23
| | | | | | | | | | | | | | | | | | | | | This backports patches leds: turris-omnia: convert to use dev_groups leds: turris-omnia: Use sysfs_emit() instead of sprintf() leds: turris-omnia: Drop unnecessary mutex locking leds: turris-omnia: Do not use SMBUS calls leds: turris-omnia: Make set_brightness() more efficient leds: turris-omnia: Support HW controlled mode via private trigger leds: turris-omnia: Add support for enabling/disabling HW gamma correction leds: turris-omnia: Fix brightness setting and trigger activating into backport-5.15. The above patches replace: leds: turris-omnia: support HW controlled mode via private trigger leds: turris-omnia: initialize multi-intensity to full leds: turris-omnia: change max brightness from 255 to 1 from mvebu/patches-5.15. Signed-off-by: Marek Behún <kabel@kernel.org>
* bcm53xx: update patch fixing NVMEM driver for NVRAMRafał Miłecki2023-10-23
| | | | | | | 1. Avoid corrupting (replacing '=' with '\0') NVRAM content 2. Check actual NVRAM data length to avoid allocating huge buffers Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Revert "lantiq: xrx200: mark subtarget as source-only"Hauke Mehrtens2023-10-23
| | | | | | | | | | | | | | | | | | | This reverts commit 0c117e1f6ccbee684ea0589d9024ca9dec4679c9. Activate the lantiq/xrx200 target again. There are still some problems with the GSWIP, but it is not leaking packets to the wrong bridge in normal operations. It shows some error messages at configuration like these: [ 54.308861] gswip 1e108000.switch: port 5 failed to add ce:9d:84:d1:81:f0 vid 1 to fdb: -22 [ 54.325633] gswip 1e108000.switch: port 5 failed to add e8:de:27:95:c1:b4 vid 0 to fdb: -22 [ 54.351242] gswip 1e108000.switch: port 5 failed to add e8:de:27:95:c1:b4 vid 1 to fdb: -22 [ 54.358311] gswip 1e108000.switch: port 5 failed to delete ce:9d:84:d1:81:f0 vid 1 from fdb: -2 The problems are described in this pull request: https://github.com/openwrt/openwrt/pull/13200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-mediatek: fix global pll clock override on mtk_spimNicolò Veronese2023-10-22
| | | | | | | | | | | | With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch a new system to calculate the SPI clocks has been added. Unfortunately, the do_div macro overrides the global priv->pll_clk_rate field. This will cause to have a reduced clock rate on each subsequent SPI call. Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu> Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* libnl: add support for cliKoen Vandeputte2023-10-22
| | | | | | | | | | Some packages (like wavemon >= 0.9.4) depend on libnl-cli. Add support for this part of the lib. libnl-cli itself depends on libnl-genl and libnl-nf. On MIPS, this component adds 81kB. Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com> (punctuation correction and reorganisation of commit message) Signed-off-by: Nick Hainke <vincent@systemli.org>
* bcm53xx: Linksys EA9200 nvram and 02_network fixesRani Hod2023-10-22
| | | | | | | | | | 1) clear nvram partialboots upon successful boot This behavior is already defined for EA9500; enabled for EA9200 too. 2) fix MAC address in board.d/02_network Use the correct nvram variable to derive lan/wan MAC address. Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ramips: TP-link archer A6/C6 device tree updatesRani Hod2023-10-22
| | | | | | | | | | | | | | | | Set correct GPIO (10) for the WPS button. This matches GPIO settings in vendor GPL sources. Note that GPL sources also mention a USB indicator LED (GPIO 13) but the device has neither an external USB port nor a USB LED. In addition, prefixes (button-, led-) are added to relevant DT entries, as well as color and function specifications for LEDs. Closes: #13736 Reported-by: Waldemar Czabaj <kaball@wp.pl> Signed-off-by: Rani Hod <rani.hod@gmail.com> (added led mitigations for wifi leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* uboot-mvebu: armada 388 clearfog: support additional ddr configurationsJosua Mayer2023-10-22
| | | | | | | | | Fixes Issue #13632. Patches as submitted in v1 to u-boot mailinglist: https://lists.denx.de/pipermail/u-boot/2023-October/533148.html Signed-off-by: Josua Mayer <josua@solid-run.com>
* tools: mold: update to v2.3.1Andre Heider2023-10-22
| | | | | | | | Release notes: https://github.com/rui314/mold/releases/tag/v2.3.0 https://github.com/rui314/mold/releases/tag/v2.3.1 Signed-off-by: Andre Heider <a.heider@gmail.com>
* kernel: bump 6.1 to 6.1.59John Audia2023-10-21
| | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.59 Manually rebased: bcm27xx/patches-6.1/950-0124-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch Removed upstreamed: generic/backport-6.1/781-v6.6-02-net-dsa-qca8k-fix-potential-MDIO-bus-conflict-when-a.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.59&id=881050b25b1dda7b0f14d40d1b09bf38cb3b427c Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.58John Audia2023-10-21
| | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.58 All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: fix missing regmap-mmio dependency for rtc-r7301Christian Marangi2023-10-20
| | | | | | | Add missing regmap-mmio dependency for rtc-r7301 to fix packaging error. Fixes: f2bc4c1f1588 ("kernel: Add kmod-rtc-r7301") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: 6.1: Backport Turris Omnia LED patchesMarek Mojík2023-10-20
| | | | | | | | | | | | | | | | | | | | This backports patches leds: turris-omnia: Use sysfs_emit() instead of sprintf() leds: turris-omnia: Drop unnecessary mutex locking leds: turris-omnia: Do not use SMBUS calls leds: turris-omnia: Make set_brightness() more efficient leds: turris-omnia: Support HW controlled mode via private trigger leds: turris-omnia: Add support for enabling/disabling HW gamma correction leds: turris-omnia: Fix brightness setting and trigger activating into backport-6.1. The above patches replace: leds: turris-omnia: support HW controlled mode via private trigger leds: turris-omnia: initialize multi-intensity to full leds: turris-omnia: change max brightness from 255 to 1 from mvebu/patches-6.1. Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
* toolchain: link ldd when using external toolchainArien Judge2023-10-20
| | | | | | | | When using an external toolchain, ldd is not linked into the rootfs. This causes subsequent upgrades to fail with 'Failed to exec upgraded'. This patch adds the symlink when using an external toolchain and musl. Signed-off-by: Arien Judge <arienjudge@outlook.com>
* uboot-mediatek: fix typo in bootmenu for GL-MT6000Jianhui Zhao2023-10-20
| | | | | | Fixes: fe10f97 ("filogic: add support for GL.iNet GL-MT6000") Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Powered by cgit, Themed by Ted Yin.