From 44168fda7800dfdd28c8d51fa92b4863f4fd6ea9 Mon Sep 17 00:00:00 2001
From: Mantas Pucka <mantas@8devices.com>
Date: Mon, 22 Jan 2024 11:28:32 +0200
Subject: qualcommax: ipq60xx: Add 8devices Mango DVK

8devices Mango DVK is a single board computer / devkit for 8devices Mango
system-on-module (SoM).

Specifications:
* CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz
* RAM: 512 MB
* Storage:
    * 32 MB serial NOR flash (on SoM)
    * 256 MB parallel NAND flash (on DVK)
* Ethernet:
    * 2x1G RJ45 ports(QCA8072 or QCA8075)
    * 1x2.5G RJ45 port (QCA8081)
    * 1xSFP (shares SGMII with QCA8081)
* Switch: Qualcomm Atheros IPQ6010
* WLAN:
    * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate
    * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate
* USB:
    * 1x USB3.0 Type-A port
    * 1x USB2.0 available at mini PCIe slot
* PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s)
* SD/eMMC (on a single shared bus - only one can be active):
    * micro SD slot
    * eMMC module connector
* LEDs:
    * Green power led (not controllable)
    * Green 2.4GHz radio led (GPIO 67)
    * Green 5GHz radio led (GPIO 66)
* Buttons:
    * 1x (WPS GPIO79) button
* GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level)
* UART: 4-pin UART header (3.3V level)
    * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2)
* Power:
    * PoE IN on 2.5G port (passive 24-48V)
    * DC power terminal (12-58V)

Installation instructions:

Vendor image format is compatible with squashfs-sysupgrade image. Run:

sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin

Signed-off-by: Mantas Pucka <mantas@8devices.com>
---
 .../ipq60xx/base-files/etc/board.d/02_network      | 28 ++++++++++++++++++++++
 .../etc/hotplug.d/firmware/11-ath11-caldata        | 20 ++++++++++++++++
 .../ipq60xx/base-files/lib/upgrade/platform.sh     | 17 +++++++++++++
 3 files changed, 65 insertions(+)
 create mode 100644 target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
 create mode 100644 target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
 create mode 100644 target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh

(limited to 'target/linux/qualcommax/ipq60xx')

diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
new file mode 100644
index 0000000000..081d894e1e
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
@@ -0,0 +1,28 @@
+#
+# Copyright (c) 2015 The Linux Foundation. All rights reserved.
+# Copyright (c) 2011-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+
+ipq60xx_setup_interfaces()
+{
+	local board="$1"
+
+	case "$board" in
+	8devices,mango-dvk)
+		ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
+		;;
+	*)
+		echo "Unsupported hardware. Network interfaces not initialized"
+		;;
+	esac
+}
+
+board_config_update
+board=$(board_name)
+ipq60xx_setup_interfaces $board
+board_config_flush
+
+exit 0
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
new file mode 100644
index 0000000000..c14722c799
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
@@ -0,0 +1,20 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions/caldata.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath11k/IPQ6018/hw1.0/cal-ahb-c000000.wifi.bin")
+	case "$board" in
+	8devices,mango-dvk)
+		caldata_extract "0:ART" 0x1000 0x20000
+		;;
+	esac
+	;;
+*)
+	exit 1
+	;;
+esac
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
new file mode 100644
index 0000000000..3d3c17b3b9
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
@@ -0,0 +1,17 @@
+PART_NAME=firmware
+REQUIRE_IMAGE_METADATA=1
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv head'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+platform_check_image() {
+	return 0;
+}
+
+platform_do_upgrade() {
+	case "$(board_name)" in
+	*)
+		default_do_upgrade "$1"
+		;;
+	esac
+}
-- 
cgit v1.2.3