aboutsummaryrefslogtreecommitdiff
path: root/target
Commit message (Collapse)AuthorAge
...
* generic: kernel: add missing symbolPawel Dembicki2023-10-19
| | | | | | It was found during work on layerscape target. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: port "-Werror" fix from NXP treePawel Dembicki2023-10-19
| | | | | | | | | | | | | | | | At this moment, 702-phy-Add-2.5G-SGMII-interface-mode.patch cause error durring kernel compilation: CC drivers/net/phy/phylink.o drivers/net/phy/phylink.c: In function 'phylink_get_capabilities': drivers/net/phy/phylink.c:443:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch] 443 | switch (interface) { | ^~~~~~ cc1: all warnings being treated as errors NXP take care of it. Let's port their patch. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: add 6.1 kernel as testingPawel Dembicki2023-10-18
| | | | | | It allow to test 6.1 kernel in Layerscape. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: 6.1: refresh kernel configPawel Dembicki2023-10-18
| | | | | | Done by 'make kernel_oldconfig'. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: copy config 5.15 to 6.1Pawel Dembicki2023-10-18
| | | | | | Configs was just copied. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: refresh kernel configPawel Dembicki2023-10-18
| | | | | | Done by 'make kernel_oldconfig'. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* layerscape: copy patches 5.15 to 6.1Pawel Dembicki2023-10-18
| | | | | | | | | | | | Patches recreated from NXP 6.1 tree: 400-LF-20-3-mtd-spi-nor-Use-1-bit-mode-of-spansion-s25fs.patch 701-staging-add-fsl_ppfe-driver.patch 702-phy-Add-2.5G-SGMII-interface-mode.patch Patch 703 includes changes made by Christian Marangi, extracted from commit 0d4a547905d4. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* Revert "ramips: convert MT7915 EEPROM to NVMEM format"Shiji Yang2023-10-17
| | | | | | | | | | | | | | | | Some MT7915 devices need to load the second part of the eeprom to work properly. The mt76 driver is not yet ready to read the pre-cal data via the NVMEM cell. Therefore, partially revert commit to fix the device probe issue on some devices. P.S. Except for D-Link and Ubnt devices, It is still uncertain whether pre-cal data is required for other devices in the patch. This partially reverts commit 9ac891f8c44124e931c15f1257347cd8ba311a19. Fixes: https://github.com/openwrt/openwrt/issues/13700 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add missing mt76 packages for Telco Electronics X1Shiji Yang2023-10-17
| | | | | | | | Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are driven by kmod-mt7603 and kmod-mt76x2. Ref: 73e0f52b6e4e ("ramips: add support for Telco Electronics X1") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix factory partition size for SNR-CPE-W4NShiji Yang2023-10-17
| | | | | | | | | The starting address of 'factory' partition is 0x40000, and the starting address of the next partition is 0x50000. It's obvious that the correct size for the 'factory' is 0x10000, just like other MT7620 devices. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix frequency limit property for some Edimax devicesShiji Yang2023-10-17
| | | | | | | | These three devices uses MT7612E PCIe NIC and supported by the 'mt76' driver. So the right frequency limit property should be `ieee80211-freq-limit`. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: remove useless status property from wmac dts nodeShiji Yang2023-10-17
| | | | | | | | On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by default except mt7628. There is no need to mark them as 'okay' again. So these useless properties can be removed. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert mt76 PCIe NIC EEPROM to NVMEM format for legacy SoCsShiji Yang2023-10-17
| | | | | | | | | | This patch converts MT761{0,2,3} PCIe WiFi calibration data to NVMEM format for legacy Ralink SoCs (MT7620 and Mt7628). The EEPROM size of the MT7610 and MT7612 is 0x200. there are only three devices uses MT7613 NIC, ASUS RT-AC1200 V2, COMFAST CF-WR758AC V2 and Keenetic KN-1613. The EEPROM size of them is 0x4da8. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert MT7628 EEPROM to NVMEM formatShiji Yang2023-10-17
| | | | | | | This patch converts MT7628 WiFi calibration data to NVMEM format. The EEPROM size is 0x400. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert rt2x00 EEPROM to NVMEM formatShiji Yang2023-10-17
| | | | | | | This patch converts legacy Ralink SoCs and MT7620 WiFi calibration data to NVMEM format. The EEPROM size is 0x200. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix mtd partition node names for Phicomm PSG1208Shiji Yang2023-10-17
| | | | | | | | The mtd partition node name should be "partition@${offset}". However, the offsets of the PSG1208 don't match the partition 'reg' properties. This patch correct the wrong offsets. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix DTS EEPROM property for some MT7628 devicesShiji Yang2023-10-17
| | | | | | | The MT7628 integrated wireless is driven by `mt76`, so the right EEPROM property name is `mediatek,mtd-eeprom`. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert the remaining mtd-mac-address to NVMEM formatShiji Yang2023-10-17
| | | | | | | | `mtd-mac-address` has been abandoned. Therefore, convert them to NVMEM format. This patch also removes some useless mtd-mac-address properties. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* qualcommax: ipq8074: use upstreamed CPUFreq NVMEM supportRobert Marko2023-10-16
| | | | | | | | | | IPQ8074 CPUFreq NVMEM support has finally landed upstream, so lets use the upstreamed version. This has a benefit of also supporting IPQ8174 (Oak) family for which SMEM SoC ID-s were also upstreamed. Signed-off-by: Robert Marko <robimarko@gmail.com>
* lantiq: update binding for ralink EEPROM swapChristian Marangi2023-10-16
| | | | | | | | | Binding for ralink EEPROM swap changed from ralink,mtd-eeprom-swap to ralink,eeprom-swap. Update every entry. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: fix ZyXEL NR7101 bricking typoBjørn Mork2023-10-15
| | | | | | | | | | A typo snuck in with the addition of Cudy M1800, changing "nr7101" to "nt7101". The result is a default network config for NR7101 without the only ethernet interface on the NR7101, thereby soft bricking it. Fixes: f6d394e9f2fd ("ramips: add support for Cudy M1800") Signed-off-by: Bjørn Mork <bjorn@mork.no>
* qualcommax: add pending GPLL parent fixesRobert Marko2023-10-15
| | | | | | | | | | | | | | | | | | | | SBL will configure IPQ807x cores to boot at 800MHz as a safe default frequency that is provided by GPLL0, but GPLL0 is not currently configured as a possible parent in the APSS clock driver not being passed to it via DTS which will then cause the kernel to not properly identify the current CPU frequency during booting and will think that CPU is currently at XO frequency of 19.2MHz instead of 800MHz cores are actually at and print: cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 19200 KHz, changing to: 1017600 KHz So, lets import patches pending upstream to prevent GPLL scaling and feed the GPLL0 clock to APSS clock driver so we get: cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz This is mostly cosmetic fix, but with all of the possible SBL and FW versions there could be edge cases resolved by this and not scaling GPLL-s anymore. Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: bump 6.1 to 6.1.57John Audia2023-10-14
| | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.57 Manually rebased: generic/pending-6.1/702-net-ethernet-mtk_eth_soc-enable-threaded-NAPI.patch Removed upstreamed: qualcommax/patches-6.1/0134-PCI-qcom-Fixing-broken-pcie-enumeration-for-2_3_3-co.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.57&id=2dfb5f324d799f4545e17631415aba6d302a8e2b Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: John Audia <therealgraysky@proton.me>
* config-6.1: disable CONFIG_ARM64_ERRATUM_2966298John Audia2023-10-14
| | | | | | | | Disable new ksym globally as OpenWrt does not have any targets that use A520 cores. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: wpj563: enable 2nd USB controllerKoen Vandeputte2023-10-13
| | | | | | | | | | | | The compex WPJ563 actually has both usb controllers wired: usb0 --> pci-e slot usb1 --> pin header As the board exposes it for generic use, enable this controller too. fixes: #13650 Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* bcm53xx: build a single device per profileRani Hod2023-10-13
| | | | | | | | | | | | | | So far every build of a single bcm53xx Target Profile (it means: when NOT using CONFIG_TARGET_MULTI_PROFILE) resulted in all target devices images being built. Now it only builds the one matching selected profile. Fixes: #13572 Suggested-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com> [rmilecki: update commit subject + body & move PROFILES line] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.15 to 5.15.135John Audia2023-10-12
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.135 All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* lantiq: Fix an sleeping function called from invalid contextHauke Mehrtens2023-10-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ifx_pcie_bus_enum_hack() function is called in ifx_pcie_read_config() while holding the ifx_pcie_lock spinlock. The ifx_pcie_bus_enum_hack() function calls pci_get_slot() which could sleep. Add a new function for pci_get_slot() which does not use a semaphore, the mutex should be sufficient. This fixes the sleep in atomic context which could cause a hang of the system. This fixes the following warning seen with CONFIG_KERNEL_DEBUG_ATOMIC_SLEEP=y. [ 12.264300] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 12.272226] BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1487 [ 12.280684] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 9, name: kworker/u4:0 [ 12.288781] CPU: 0 PID: 9 Comm: kworker/u4:0 Not tainted 5.15.134 #0 [ 12.295135] Workqueue: events_unbound deferred_probe_work_func [ 12.300964] Stack : 80e70000 8008ac80 00000000 00000004 807c776c 8145b9ec 81424c00 800520ec [ 12.309316] 808a0000 8145ba2b 8145b844 8145b838 80414178 00000001 8145b9f8 81439ea0 [ 12.317674] 00000000 00000000 807c776c 8145b838 ffffefff 00000000 00000000 ffffffea [ 12.326030] 00000081 8145b844 00000081 808a6f50 807c776c 00000000 00000000 80910000 [ 12.334391] 00111bef 00000000 00000001 00000000 00000018 00000030 00000000 80e40000 [ 12.342741] ... [ 12.345177] Call Trace: [ 12.347613] [<8000c1d0>] show_stack+0x28/0xf0 [ 12.351974] [<8038ba1c>] dump_stack_lvl+0x60/0x80 [ 12.356667] [<8005eefc>] ___might_sleep+0x124/0x138 [ 12.361547] [<806daf30>] down_read+0x24/0x88 [ 12.365807] [<803cdd20>] pci_get_slot+0x2c/0xc0 [ 12.370333] [<806d56ac>] ifx_pcie_read_config+0x164/0x330 [ 12.375735] [<803be610>] pci_bus_read_config_dword+0x6c/0xd0 [ 12.381399] [<803c20cc>] pci_bus_generic_read_dev_vendor_id+0x3c/0x1a8 [ 12.387915] [<803c27ec>] pci_scan_single_device+0x88/0x154 [ 12.393404] [<803c2928>] pci_scan_slot+0x70/0x134 [ 12.398099] [<803c3bf0>] pci_scan_child_bus_extend+0x5c/0x320 [ 12.403849] [<803c4178>] pci_scan_root_bus_bridge+0xd0/0xec [ 12.409414] [<806d45a8>] pcibios_scanbus+0xe4/0x21c [ 12.414293] [<806d4908>] register_pci_controller+0xb8/0x11c [ 12.419858] [<806d5f9c>] ifx_pcie_bios_probe+0x724/0x940 [ 12.425174] [<80417574>] platform_probe+0x38/0x90 [ 12.429868] [<80414d68>] really_probe.part.0+0xac/0x354 [ 12.435103] [<80415298>] driver_probe_device+0x4c/0x154 [ 12.440313] [<80415904>] __device_attach_driver+0xd0/0x15c [ 12.445802] [<804129d8>] bus_for_each_drv+0x70/0xb0 [ 12.450676] [<80415610>] __device_attach+0xdc/0x194 [ 12.455545] [<80413ca8>] bus_probe_device+0x9c/0xb8 [ 12.460419] [<8041420c>] deferred_probe_work_func+0x94/0xd4 [ 12.465995] [<8004fcb4>] process_one_work+0x27c/0x4c8 [ 12.471044] [<80050710>] worker_thread+0x34c/0x5f8 [ 12.475825] [<800587a8>] kthread+0x168/0x18c [ 12.480090] [<80006ef8>] ret_from_kernel_thread+0x14/0x1c Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: add support for HPE 1920-8g-poe+ (65W)Kevin Jilissen2023-10-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware information: --------------------- - RTL8380 SoC - 8 Gigabit RJ45 PoE ports (built-in RTL8218B) - 2 SFP ports (built-in SerDes) - RJ45 RS232 port on front panel - 32 MiB NOR Flash - 128 MiB DDR3 DRAM - PT7A7514 watchdog - PoE chip - Fanless Known issues: --------------------- - PoE LEDs are uncontrolled. (Manual taken from f2f09bc) Booting initramfs image: ------------------------ - Prepare a FTP or TFTP server serving the OpenWrt initramfs image and connect the server to a switch port. - Connect to the console port of the device and enter the extended boot menu by typing Ctrl+B when prompted. - Choose the menu option "<3> Enter Ethernet SubMenu". - Set network parameters via the option "<5> Modify Ethernet Parameter". Enter the FTP/TFTP filename as "Load File Name" ("Target File Name" can be left blank, it is not required for booting from RAM). Note that the configuration is saved on flash, so it only needs to be done once. - Select "<1> Download Application Program To SDRAM And Run". Initial installation: --------------------- - Boot an initramfs image as described above, then use sysupgrade to install OpenWrt permanently. After initial installation, the bootloader needs to be configured to load the correct image file - Enter the extended boot menu again and choose "<4> File Control", then select "<2> Set Application File type". - Enter the number of the file "openwrt-kernel.bin" (should be 1), and use the option "<1> +Main" to select it as boot image. - Choose "<0> Exit To Main Menu" and then "<1> Boot System". NOTE: The bootloader on these devices can only boot from the VFS filesystem which normally spans most of the flash. With OpenWrt, only the first part of the firmware partition contains a valid filesystem, the rest is used for rootfs. As the bootloader does not know about this, you must not do any file operations in the bootloader, as this may corrupt the OpenWrt installation (selecting the boot image is an exception, as it only stores a flag in the bootloader data, but doesn't write to the filesystem). Example PoE config file (/etc/config/poe): --------------------- config global option budget '65' config port option enable '1' option id '1' option name 'lan8' option poe_plus '1' option priority '2' config port option enable '1' option id '2' option name 'lan7' option poe_plus '1' option priority '2' config port option enable '1' option id '3' option name 'lan6' option poe_plus '1' option priority '2' config port option enable '1' option id '4' option name 'lan5' option poe_plus '1' option priority '2' config port option enable '1' option id '5' option name 'lan4' option poe_plus '1' option priority '2' config port option enable '1' option id '6' option name 'lan3' option poe_plus '1' option priority '2' config port option enable '1' option id '7' option name 'lan2' option poe_plus '1' option priority '2' config port option enable '1' option id '8' option name 'lan1' option poe_plus '1' option priority '2' Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
* realtek: rename hpe,1920-8g-poe to match hardwareKevin Jilissen2023-10-09
| | | | | | | | | | | | | There are two hardware models of the HPE 1920-8g-poe switch. The version currently in the repository is the model with a PoE budget of 180W. In preparation of the addition of the 65W model, the existing model is renamed to clarify the hardware version it targets. As suggested by Pawel, the 'SUPPORTED_DEVICES' includes the old target name to enable an upgrade path of builds with the old name. Suggested-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
* ath79: add WWAN serial driver for GL.iNET GL-XE300David Bauer2023-10-09
| | | | | | | | | | | The driver for the cellular modems serial interface was missing from the default device packages. The driver is required to interact with the modem using AT commands. Other devices with a 4G modem also ship with this package, thus let's add it to the default packages for the board. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: fix broken onhub dtsiChristian Marangi2023-10-09
| | | | | | | | | | Fix broken onhub dtsi. The gmac node have a redundant phy-handle that doesn't point to the swconfig phy node as they got dropped in the DSA conversion. Drop these extra binding to restore correct compilation of this subtarget. Fixes: 337e36e0ef98 ("ipq806x: convert each device to DSA implementation") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: convert MT7915 EEPROM to NVMEM formatShiji Yang2023-10-09
| | | | | | | This patch converts MT7915 WiFi calibration data to NVMEM format. The EEPROM size is 0xe00. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert MT7613 and MT7615 EEPROM to NVMEM format for MT7621Shiji Yang2023-10-09
| | | | | | | This patch converts MT7613 and MT7615 WiFi calibration data to NVMEM format. The EEPROM size is 0x4da8. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert MT7610 and MT7612 EEPROM to NVMEM format for MT7621Shiji Yang2023-10-09
| | | | | | | This patch converts MT7610 and MT7612 WiFi calibration data to NVMEM format. The EEPROM size is 0x200. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: convert MT7603 EEPROM to NVMEM formatShiji Yang2023-10-09
| | | | | | | This patch converts MT7603 WiFi calibration data to NVMEM format. The EEPROM size is 0x400. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: correct NVMEM MAC address node name and label for Bolt ArionShiji Yang2023-10-09
| | | | | | | The node name&label should match the address in the 'reg' property, so it's better to change the incorrect offset to the 0x28. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: fix EEPROM size for I-O DATA WN-DEAX1800GRShiji Yang2023-10-09
| | | | | | | | I-O DATA WN-DEAX1800GR uses MT7915 PCIe NIC. The correct EEPROM size is 0xe00. Fixes: ac68fbf526d ("ramips: add support for I-O DATA WN-DEAX1800GR") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: bump 6.1 to 6.1.56John Audia2023-10-08
| | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.56 Removed upstreamed: bcm53xx/patches-6.1/032-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.56&id=226590fbd96717fce218878044df3568c825ba8e Build system: x86/64 Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.134John Audia2023-10-07
| | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.134 Removed upstreamed: generic/backport-5.15/894-Fix-up-backport-for-13619703038.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.134&id=d7acb7031758141225844bea073860b48fd92092 Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* generic: 6.1: backport qca8k fixes for big endian and MDIOChristian Marangi2023-10-06
| | | | | | | | Backport qca8k fixes for big endian system (to make them working again) and a patch fixing MDIO conflicts if other PHY are connected and mgmt eth is used to control the switch. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 6.1: add patch enabling assisted learning for qca8kChristian Marangi2023-10-06
| | | | | | | Add patch enabling assisted learning for qca8k to fix roaming issue between BSS and BSS on the same L2 broadcast domain. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 6.1: fix compilation warning for CONFIG_PROC_STRIPPEDChristian Marangi2023-10-06
| | | | | | | | | | | | | | Fix compilation warning for CONFIG_PROC_STRIPPED for kernel 6.1. Fix compilation warning: make[4]: Leaving directory '/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-ath79_tiny/linux-6.1.55' net/ipv4/inet_timewait_sock.c: In function '__inet_twsk_schedule': net/ipv4/inet_timewait_sock.c:272:22: error: unused variable 'kill' [-Werror=unused-variable] 272 | bool kill = timeo <= 4*HZ; | ^~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 6.1: add missing config SPI_BCM63XX_HSSPIChristian Marangi2023-10-06
| | | | | | | Add missing config SPI_BCM63XX_HSSPI for kernel 6.1 triggered on compilation of bcm4908. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ath79: mikrotik: fix build error with kernel 6.1Koen Vandeputte2023-10-06
| | | | | | | | | | | | | | | | drivers/mfd/rb4xx-cpld.c:167:19: error: initialization of 'void (*)(struct spi_device *)' from incompatible pointer type 'int (*)(struct spi_device *)' [-Werror=incompatible-pointer-types] 167 | .remove = rb4xx_cpld_remove, | ^~~~~~~~~~~~~~~~~ drivers/mfd/rb4xx-cpld.c:167:19: note: (near initialization for 'rb4xx_cpld_driver.remove') cc1: some warnings being treated as errors make[8]: *** [scripts/Makefile.build:250: drivers/mfd/rb4xx-cpld.o] Error 1 make[7]: *** [scripts/Makefile.build:500: drivers/mfd] Error 2 make[6]: *** [scripts/Makefile.build:500: drivers] Error 2 make[5]: *** [Makefile:2012: .] Error 2 As the allocated function does nothing, simply delete it. Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* generic: rtl8366_smi: rename and drop conflicting vlan GPL symbolsChristian Marangi2023-10-06
| | | | | | | | | | | | Symbol rtl8366_enable_vlan and rtl8366_reset_vlan are also present in the DSA driver upstream and conflicts as they are EXPORTED. Rename them to rtl8366_smi_enable_vlan and rtl8366_smi_reset_vlan to fix the conflict. While at it also make them static and drop the EXPORT_SYMBOL_GPL as they are not actually used by any other driver and exporting them is useless. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* armsr: armv8: Enable KASLR in kernel 6.1Javier Tia2023-10-05
| | | | | | | In userspace, ASLR is enabled, but it's missing to enable KASLR on the kernel side to improve security as part of SystemReady recommendations. Signed-off-by: Javier Tia <javier.tia@linaro.org>
* mediatek: fix wrong variable name in patch for Linux 6.1Daniel Golle2023-10-05
| | | | | | | | | | The name of the variable holding the pointer to the private struct has changed between Linux 5.15 and Linux 6.1 and adding the identical patch fixing PCIe #PERST de-assert broke the build on Linux 6.1. Also change the name in the patch to fix the build. Fixes: 6a2e17d5c1 ("mediatek: fix PCIe #PERST being de-asserted too early") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq806x: fix wrong QCA8K LED definition for NEC Aterm WG2600HP3Christian Marangi2023-10-05
| | | | | | | | | | | Fix copy-paste error in migrating NEC Aterm WG2600HP3 to new LED implementation for the QCA8K switch. Correct define the missing additional LED pin used for each port and fix wrong color for LED 2 for each port. Also add the required function-enumerator as all 3 LED have the same color and function. Fixes: c707cff6c94b ("ipq806x: add LEDs definition for non-standard qca8k LEDs") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq806x: add support for Extreme Networks AP3935Glen Lee2023-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee <g2lee@yahoo.com>
Powered by cgit, Themed by Ted Yin.