aboutsummaryrefslogtreecommitdiff
path: root/target
Commit message (Collapse)AuthorAge
...
* mediatek: add support for Confiabits MT7981Luis Mita2023-11-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981. Specification: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 128 MiB SPI NAND - RAM: 256 MiB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax) - Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN) - USB 2.0 port - Buttons: 1 Reset button, 1 Mesh button. - LEDs: 7x light-blue, 2x warm-white - Serial console: internal 4-pin header, 115200 8n1 - Power: 12 VDC, 1.5 A MAC addresses in stock firmware and in this commit: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 00:0c:43:xx:xx:e1 | label+1 | | LAN | 00:0c:43:xx:xx:e0 | label | | WLAN 2g | 00:0c:43:xx:xx:e0 | label | | WLAN 5g | 02:0c:43:xx:xx:e0 | | +---------+-------------------+-----------+ The label MAC was found in 'Factory', 0x4 Installation: The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image with the 'Keep settings' option turned off. Signed-off-by: Luis Mita <luis@luismita.com>
* target: Make TARGET_SERIAL independent of GRUB configurationHauke Mehrtens2023-11-29
| | | | | | | | | | | | | GRUB_SERIAL is also used for the default serial on the target and not only in grub. When no grub was build it was not available and the build fails. Rename GRUB_SERIAL to TARGET_SERIAL and make it always available on x86 and armsr targets. Fixes: #14063 Fixes: b10768476f9d ("x86,armsr: interpolate GRUB_SERIAL into /etc/inittab") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.15 to 5.15.140John Audia2023-11-29
| | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.140 Removed upstreamed: mvebu/patches-5.15/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.140&id=06d320ca170b4e59bb261e2ce3ffe84e9154d42b Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.64John Audia2023-11-29
| | | | | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.64 Removed upstreamed: ixp4xx/patches-6.1/0001-mtd-cfi_cmdset_0001-Byte-swap-OTP-info.patch[1] mvebu/patches-6.1/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[2] qualcommax/patches-6.1/0026-v6.7-clk-qcom-ipq8074-drop-the-CLK_SET_RATE_PARENT-flag-f.patch[3] Manually rebased: bcm27xx/patches-6.1/950-0111-MMC-added-alternative-MMC-driver.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=3b93096d29c5b9ca2af94be4ee9949c1767acf17 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=b3fd9db79e30d5eb5f76ef1f5b7e4f444af574ea 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=877080a3490102da26b8d969588159b2385f739e Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: add kmod-usb3 to default package set of the ZBT-Z8102AXDaniel Golle2023-11-29
| | | | | | | Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are required to be able to use the USB-connected M.2 slots for 4G/5G modems. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: copy config for Acer Predator W6David Bauer2023-11-27
| | | | | | Config was previously not copied on sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add support for GL.iNet GL-MT2500David Bauer2023-11-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7981BA RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR) MMC: 8GB eMMC (Samsung 8GTF4R) ETH: 1000Base-T LAN (ePHY) 2500Base-T WAN (MaxLinear GPY211C) BTN: 1x Reset Button LED: System (blue/white) VPN (white) USB: 1x USB-A (USB 3.0) UART: 115200 8N1 - Pinout on board next to LAN port Don't connect 3.3V! Known Issues ------------ U-Boot vendor recovery does not seem to accept any images, neither GL.iNet images nor OpenWrt images. Recovery requires serial access! Installation ------------ Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to not retain existing settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: require image metadataDavid Bauer2023-11-27
| | | | | | | | | All devices in the rockchip target have appended image-metadata. Enforce the presence of this metadata to avoid flashing incomplete images. This is the de-facto standard for almost all OpenWrt targets. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fortinet-fap-221-b: convert to nvmem-layoutLech Perczak2023-11-27
| | | | | | | | | | | | | Now that MAC address parser supports the hex format (without delimiters), use the canonical MAC address stored in U-boot partition. Get rid of the userspace adjustments which are no longer necessary. While at that, move the mac-base to the common part, as it is again exactly the same in both models. And convert ART partition too - keep that one separate, as calibration data length differs between the models. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: fortinet-fap-220-b: convert to nvmem-layoutLech Perczak2023-11-27
| | | | | | | | | Now that MAC address parser supports the hex format (without delimiters), use the canonical MAC address stored in U-boot partition. Get rid of the "mac-address-increment" binding. While at that, convert ART partition too. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: fortinet-fap-220-b: fix WLAN MAC addressesLech Perczak2023-11-27
| | | | | | | | Addresses were swapped compared to the factory firmware. In addition to that, one of them was shifted by -1. Fix that by setting wlan0 MAC offset to 9, and wlan1 MAC offset to 2. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* x86 64: Add new device Cordoba Edge PlatformXiaojun Liu2023-11-26
| | | | | | | | | | | | Add new device Cordoba Edge Platform hardware specifications: CPU - Intel Atom C3000 Ethernet - 2 10Gbps ixgbe SPF+ 2 1Gbps ixgbe RJ45/SPF 4 2.5Gbps igc RJ45 WiFi - mt7915e LED - 3 multicolor(red|blue|green) LEDs Signed-off-by: Xiaojun Liu <xiaojun.liu@silicom.co.il>
* rockchip: add NanoPi R5C supportTianling Shen2023-11-26
| | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3568 ARM64 (4 cores) 1GB or 4GB LPDDR4X RAM 2x 2500 Base-T 4 LEDs (LAN / WAN / WIFI / POWER) 1 Button (Reset) 8GB or 32GB eMMC on-board Micro-SD Slot M.2 Slot 2x USB 3.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: add NanoPi R5S supportTianling Shen2023-11-26
| | | | | | | | | | | | | | | | | | | | | | Hardware -------- RockChip RK3568 ARM64 (4 cores) 2GB or 4GB LPDDR4X RAM 1x 1000 Base-T 2x 2500 Base-T 4 LEDs (LAN1 / LAN2 / WAN / POWER) 8GB eMMC on-board Micro-SD Slot M.2 Slot 2x USB 3.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Tested-by: Packet Please <pktpls@systemli.org> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: armv8: broaden boardnameTianling Shen2023-11-26
| | | | | | Now we have rk356x support :-) Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: enable drivers for rk356xTianling Shen2023-11-26
| | | | | | | Enable all necessary drivers for the rk356x SoCs, including PHY, SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: remove kernel 5.15 patches and configTianling Shen2023-11-26
| | | | | | As we switched to kernel 6.1, these files can go. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: switch to kernel 6.1Tianling Shen2023-11-26
| | | | | | Required by the following rk3568 support. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: move image generation command to defaultTianling Shen2023-11-26
| | | | | | | | It's applicable for all devices so move it to default to reduce redudant code. Addtionally introduce a new variable `BOOT_SCRIPT` to allow custom boot script (if necessary). Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ipq40xx: enable UBI size checks for some Linksys NAND devicesTony Ambardar2023-11-26
| | | | | | | | Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300, WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved blocks on NAND devices. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* image: use helper function for size unitsTony Ambardar2023-11-26
| | | | | | | | Add the make function 'exp_units' for helping evaluate k/m/g size units in expressions, and use this to consistently replace many ad hoc substitutions like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix typo in Linksys WHW01 image definitionTony Ambardar2023-11-26
| | | | | | | | Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit conversions in build recipes (e.g. 75776k -> 75776*1024). Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for D-link DAP-1720 A1Rani Hod2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa <protectivedad@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ath79: ar: convert to mac-baseRosen Penev2023-11-25
| | | | | | Replacement for deprecated mac-address-increment Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: ar: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: tp9343: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows getting rid of deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qcn: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows getting rid of deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qca: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qca: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: mikrotik: fix dts warningsRosen Penev2023-11-25
| | | | | | property has invalid length Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: nix mac-address-incrementRosen Penev2023-11-26
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: add interrupt-controllerRosen Penev2023-11-26
| | | | | | | | Fixes dtc warning: '#interrupt-cells' found, but node is not an interrupt provider Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620a: use mac-baseRosen Penev2023-11-26
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620a: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows using mac-base to replace mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620n: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | nvmem-cells is deprecated. nvmem-layout allows using mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7628: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7628: use nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow using mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: rtxxxx: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | Deprecated and replaced upstream with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: rtxxxx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-adress-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts and image recipes to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: remove kmod-usb2 for GL-MT6000Chukun Pan2023-11-25
| | | | | | | The usb driver requires kmod-usb3, not kmod-usb2. Remove the useless kmod-usb2 from default package. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: Cetron CT3003: fixes typo for spi propertiesChukun Pan2023-11-25
| | | | | | | Same as commit 3674689, correct 'buswidth' to 'bus-width'. Also move the nmbm properties outside the partition definition. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ipq40xx: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: fix dtc warnimgRosen Penev2023-11-25
| | | | | | I2C bus unit address format error, expected "62" Signed-off-by: Rosen Penev <rosenp@gmail.com>
* qualcommax: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | nvmem-cells is deprecated Signed-off-by: Rosen Penev <rosenp@gmail.com>
* apm821xx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | nvmem-cells is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
Powered by cgit, Themed by Ted Yin.