aboutsummaryrefslogtreecommitdiff
path: root/target/linux
Commit message (Collapse)AuthorAge
* ath79: add support for ASUS RT-AC59U / ZenWiFi CD6Wenli Looi2023-07-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP, RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12. ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R is the router, and CD6N is the node. Hardware: - SoC: QCN5502 - RAM: 128 MiB - UART: 115200 baud (labeled on boards) - Wireless: - 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n currently unsupported due to missing support for QCN550x in ath9k - 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac - Flash: SPI NOR - RT-AC59U / CD6N: 16 MiB - RT-AC59U v2 / CD6R: 32 MiB - Ethernet: gigabit - RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN - CD6R: 3x LAN 1x WAN - CD6N: 2x LAN - USB: - RT-AC59U / RT-AC59U v2: 1 port USB 2.0 - CD6R / CD6N: none WiFi calibration data contains valid MAC addresses. The initramfs image is uncompressed because I was unable to boot a compressed initramfs from memory (gzip or lzma). Booting a compressed image from flash works fine. Installation: To install without opening the case: - Set your computer IP address to 192.168.1.10/24 - Power up with the Reset button pressed - Release the Reset button after about 5 seconds or until you see the power LED blinking slowly - Upload OpenWRT factory image via TFTP client to 192.168.1.1 Revert to stock firmware using the same TFTP method. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* mediatek: replace hack for MaxLinear 2.5G PHYDaniel Golle2023-07-08
| | | | | | Replace hack with proper patch also for Linux 5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: dts: mt7988a: remove boottrap hackDaniel Golle2023-07-08
| | | | | | | The PHY driver now uses regmap created from pio syscon, we no longer need the boottrap device. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: use backported Ethernet PHY driver also for 5.15Daniel Golle2023-07-08
| | | | | | | Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the driver in files-5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* layerscape: base-files: remove redundant RAMFS_COPY_* additionsMathew McBride2023-07-08
| | | | | | | All the tools (e.g fw_setenv, ubiupdatevol) and config (fw_env.config) needed for sysupgrade are already included in /lib/upgrade/stage2 Signed-off-by: Mathew McBride <matt@traverse.com.au>
* mediatek: dts: mt7988a: wire-up mediatek,pio for PHY LEDsDaniel Golle2023-07-08
| | | | | | | | | | The PHY driver needs to read a register containing the values of the bootstrap pins (which happen to be the PHY LEDs) to determine the LED polarities. Allow regmap access to first pinctrl bank by adding the 'syscon' compatible, and reference the pinctrl in the MDIO bus where the PHY driver will look for it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: remove CRYPTO_BLAKE2S from all >=5.15Christian Svensson2023-07-08
| | | | | | | | | This option was removed from upstream kernel back in 2022. See commits: 2d16803c562ecc644803d42ba98a8e0aef9c014e (>=6.0) 3dd33a09f5dc12ccb0902923c4c784eb0f8c7554 (>=5.15.61 backport) Signed-off-by: Christian Svensson <blue@cmd.nu>
* kernel: add two missing symbols in 6.1Daniel Golle2023-07-08
| | | | | | | Two more new symbols were discovered when building mediatek targets with CONFIG_ALL_KMODS=y. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* apm821xx: fix autoloading of kmod-hw-crypto4xxRani Hod2023-07-08
| | | | | Fixes: 55fbcad20a2d (apm821xx: make crypto4xx as a standalone module) Signed-off-by: Rani Hod <rani.hod@gmail.com>
* kernel: bump 5.15 to 5.15.120John Audia2023-07-07
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: expose testing Linux 6.1 testing kernelDaniel Golle2023-07-07
| | | | | | | Set KERNEL_TESTING_PATCHVER:=6.1 to allow building all subtargets with Linux 6.1. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: adapt kernel configuration for Linux 6.1Daniel Golle2023-07-07
| | | | | | Update kernel configuration to build Linux 6.1 for all subtargets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: copy config-5.15 to config-6.1 for all subtargetsDaniel Golle2023-07-07
| | | | | | | To ease review, first copy all subtargets' kernel config-5.15 to the to-be-adapted config-6.1. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: adapt files and patches for Linux 6.1Daniel Golle2023-07-07
| | | | | | | | | With Linux 6.1 many of our downstream patches and out-of-tree files can be removed or at least replaced by backported upstream commits. Signed-off-by: Daniel Golle <daniel@makrotopia.org> [fix CMDLINE_OVERRIDE for arm64] Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: copy patches and files for Linux 6.1Daniel Golle2023-07-07
| | | | | | | First step only copies patches-5.15 and files-5.15 to patches-6.1 and files-6.1 respectively. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: prepare old rtk switch driver for use with Linux 6.1Daniel Golle2023-07-07
| | | | | | | | | | The old RealTek RTL8367S switch driver which is used for some MT7622 devices needs to be modified to no longer free the GPIO after reset has completed. This is due to Linux 5.19 removing devm_gpio_free via commit 2b038e786f83 ("gpiolib: devres: Get rid of unused devm_gpio_free()") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: 6.1: fix uImage.FIT partitions on mtdblock and ubiblockDaniel Golle2023-07-07
| | | | | | | | | | | When refreshing the hack patches for Linux 6.1 the part of the uImage.FIT partition parser patch which takes care of allowing mtdblock and ubiblock devices to have partitions has been dropped, supposedly by accident. Re-add a that part to the patch, so devices using a uImage.FIT filesystem sub-image as rootfs can work with Linux 6.1. Fixes: 19a246bb65 ("generic: 6.1: manually refresh hack patches") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add missing symbols in 6.1Koen Vandeputte2023-07-07
| | | | | | Found these while playing with video pci media adapter support Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* kernel: add missing symbols in 5.15Koen Vandeputte2023-07-07
| | | | | | Found these while playing with video pci media adapter support Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* kernel: add CONFIG_LOCK_MM_AND_FIND_VMAJohn Audia2023-07-05
| | | | | | | | 6.1.37 introduces a new symbol[1] 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v6.1.37&id2=v6.1.36 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.37John Audia2023-07-05
| | | | | | | | | | Manually rebased: generic/hack-6.1/220-arm-gc_sections.patch armsr/patches-6.1/221-armsr-disable_gc_sections_armv7.patch All other patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.36John Audia2023-07-05
| | | | | | | | | | | | | All patches automatically rebased. Acknowledgment to @john-tho for the changes to fs.mk to accommodate new paths introduced in https://github.com/gregkh/linux/commit/29429a1f5871dbe54ee0da81bb12db8567f15379 Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: modules: add xdp-sockets-diag supportTianling Shen2023-07-05
| | | | | | Support for PF_XDP sockets monitoring interface used by the ss tool. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ipq-wifi: fix upstream board-2.bin ZTE M289F snafuChristian Lamparter2023-07-04
| | | | | | | | | | | | | | | | | | | | The upstream board-2.bin file in the linux-firmware.git repository for the QCA4019 contains a packed board-2.bin for this device for both 2.4G and 5G wifis. This isn't something that the ath10k driver supports. Until this feature either gets implemented - which is very unlikely -, or the upstream boardfile is mended (both, the original submitter and ath10k-firmware custodian have been notified). OpenWrt will go back and use its own bespoke boardfile. This unfortunately means that 2.4G and on some revisions the 5G WiFi is not available in the initramfs image for this device. Fixes: #12886 Reported-by: Christian Heuff <christian@heuff.at> Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86/64: set CONFIG_NVME_HWMON=yJohn Audia2023-07-04
| | | | | | | CONFIG_NVME_HWMON exposes /sys/class/nvme/nvme0/device/hwmon to allow sensors (and others) to see NVMe drive health Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: introduce KERNEL_WERROR config optionPetr Štetiar2023-07-04
| | | | | | | | | | | | | In commit b2d1eb717b65 ("generic: 5.15: enable Werror by default for kernel compile") CONFIG_WERROR=y was enabled and all warnings/errors reported with GCC 12 were fixed. Keeping this in sync with past/future GCC versions is going to be uphill battle, so lets introduce new KERNEL_WERROR config option, enable it by default only for tested/known working combinations and on buildbots. References: #12687 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86: set CONFIG_X86_AMD_PLATFORM_DEVICEJohn Audia2023-07-03
| | | | | | Needed by AMD processors using Carrizo and later chipsets Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: mt7621: add TP-Link EAP613 v1Sander Vanheule2023-07-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: fix broken 02_network scriptWenli Looi2023-07-02
| | | | | | Script was broken by an extraneous space. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* mediatek: define NMBM management region for WAX220David Bauer2023-07-02
| | | | | | | | The NETGEAR WAX220 employs NMBM on SPI-NAND. In order to avoid dealing with invalid factory data, enable NMBM in the area preceding the UBI volume. Signed-off-by: David Bauer <mail@david-bauer.net>
* realtek: Use MDIO_* constants from <linux/mdio.h>Pascal Ernster2023-07-01
| | | | | | | | | | | | | | | | | | | | To improve code readability in drivers/net/phy/rtl83xx-phy.c, replace constants MMD_AN and MMD_VEND2 from drivers/net/phy/rtl83xx-phy.h with MDIO_MMD_AN and MDIO_MMD_VEND2 from <linux/mdio.h>. Also, replace BIT(0) with MDIO_EEE_2_5GT, BIT(1) with MDIO_EEE_100TX, BIT(2) with MDIO_EEE_1000T, BIT(9) with MDIO_AN_CTRL1_RESTART, BIT(12) with MDIO_AN_CTRL1_ENABLE, 32 with MDIO_AN_10GBT_CTRL, 60 with MDIO_AN_EEE_ADV, and 62 with MDIO_AN_EEE_ADV2 from <linux/mdio.h>. Suggested-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: Pascal Ernster <git@hardfalcon.net>
* realtek: Use ADVERTISE_* and MII_PHYSID* from <linux/mii.h>Pascal Ernster2023-07-01
| | | | | | | | | | Replace BIT(x) and numerical values in drivers/net/phy/rtl83xx-phy.c with constants from <linux/mii.h> to improve code readability. To make reviewing easier, this commit only addresses ADVERTISE_* and MII_PHYSID* constants. Signed-off-by: Pascal Ernster <git@hardfalcon.net>
* realtek: Use MII_BMCR and BMCR_* constants from <linux/mii.h>Pascal Ernster2023-07-01
| | | | | | | | | | | | Replace numerical values, BIT(x) and (1 << x) in drivers/net/phy/rtl83xx-phy.c with constants from <linux/mii.h> to improve code readability. To make reviewing easier, this commit only addresses MII_BMCR and BMCR_* constants. Suggested-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: Pascal Ernster <git@hardfalcon.net>
* ramips: Add support for ComFast CF-E390AXUsama Nassir2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for ComFast CF-E390AX. It is a 802.11 wifi6 cieling AP, based on MediaTek MT7261AT. Specifications: SoC: MediaTek MT7621AT RAM: 128 MiB Flash: 16 MiB NOR (Macronix mx25l12805d) Wireless: MT7915E (2.4G) 802.11ax/b/g/n MT7915E (5G) 802.11ac/ax/n Ethernet: 2 x 1Gbs Button: 1 x "Reset" button LED: 1x Blue LED + 1x Red LED + 1x green LED Power: PoE Manufacturer Page: http://en.comfast.com.cn/index.php?m=content&c=index&a=show&catid=84&id=75 Flash Layout: 0x000000000000-0x000000030000 : "bootloader" 0x000000030000-0x000000040000 : "config" 0x000000050000-0x000000060000 : "factory" 0x000000090000-0x000001000000 : "firmware" First install: 1. Set device into http firmware fail safe upload mode by pressing the reset button for 10 seconds while powering it on. Once the LED stops flashing, safe mode will be running. 2. Set PC IP address to 192.168.1.2 3. Browse to 192.168.1.1 and upload the factory image using the web interface. Signed-off-by: Usama Nassir <usama.nassir@gmail.com>
* ath79: add support for COMFAST CF-E380AC v2Joao Henrique Albuquerque2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) COMFAST MAC addresses : Though the OEM firmware has four adresses in the usual locations, it appears that the assigned addresses are just incremented in a different way: Interface address location Lan *:00 0x0 2.4g *:0A n/a (0x0 + 10) 5g *:02 0x6 Unused Addresses found in ART hexdump address location *:01 0x1002 *:03 0x5006 To keep code consistency the MAC address assignments are made based on increments of the one found in 0x0; Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
* ramips: add support for Sercomm S1500 devicesMikhail Zhilkin2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: sercomm.mk: preparation for Sercomm s1500 devices supportMikhail Zhilkin2023-07-01
| | | | | | | | | | | | | This commit moves a part of the code from the "sercomm-factory-cqr" recipe to the separate "sercomm-mkhash" recipe. This simplifies recipes and allows insert additional recipes between these code blocks (required for the future support for Beeline SmartBox PRO router). dd automatically fills the file by 0x00 if the filesize is less than offset where we start writing. We drop such dd command so we need to add --extra-padding-size 0x190 to the sercomm-pid.py call. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ath79: DTS improvement for buzzer on RB951G-2HnDPavel Pernička2023-07-01
| | | | | | | | | | Mikrotik RB951 router has a buzzer on the board, which makes annoying noises due to the interference caused by PoE input or Wifi transmission when no GPIO pin state is set. I added buzzer node to device's DTS in order to set deault level to 1 and to provide easier access for it. Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com>
* layerscape: remove Traverse LS1043 boardsMathew McBride2023-07-01
| | | | | | | | | | | | | | | | The Traverse LS1043 boards were not publicly released, all the production has been going to OEM customers who do not use the image format defined in the OpenWrt tree. Only a few samples were circulated outside Traverse and our OEM customers. The public release (then called Five64) of this series was cancelled in favour of our LS1088A based design (Ten64). It is best to remove these boards to avoid wasting OpenWrt project and contributor resources. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* mediatek: filogic: add H3C Magic NX30 Pro supportChukun Pan2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: W25N01GVZEIG 128MB RAM: NT5CB128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. PC run command: "telnet 192.168.124.1 99" Username: H3C, password is the web login password of the router. 2. Download preloader.bin and bl31-uboot.fip 3. PC run command: "python3 -m http.server 80" 4. Download files in the telnet window: "wget http://192.168.124.xx/xxx.bin" Replace xx with your PC's IP and the preloader.bin and bl31-uboot.fip. 5. Flushing openwrt's uboot: "mtd write xxx-preloader.bin BL2" "mtd write xxx-bl31-uboot.fip FIP" 6. Connect to the router via the Lan port, set a static ip of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Download initramfs image, reboot router, waiting for tftp recovery to complete. 8. After openwrt boots up, perform sysupgrade. Note: 1. The u-boot-env partition on mtd is empty, OEM stores their env on ubi:u-boot-env. 2. Back up all mtd partitions before flashing. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: add support for Netgear EX6250v2 seriesWenli Looi2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac (Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work currently as there is no driver. Related: https://github.com/openwrt/openwrt/pull/5084 For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2. Specifications: * MT7629, 256 MiB RAM, 16 MiB SPI NOR * MT7761N (2.4GHz) / MT7762N (5GHz) - no driver * Ethernet: 1 port 10/100/1000 * UART: 115200 baud (labeled on board) Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * After installation, perform a factory reset. Wait for the device to boot, then hold the reset button for 10 seconds. This is needed because sysupgrade in the stock firmware will attempt to preserve its configuration using sysupgrade.tgz. See https://github.com/openwrt/openwrt/pull/4182 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ramips: add support for Netgear EAX12 seriesWenli Looi2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6) extenders that share the SoC, WiFi chip, and image format with the WAX202. Specifications: * MT7621, 256 MiB RAM, 128 MiB NAND * MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC) * Ethernet: 1 port 10/100/1000 * UART: 115200 baud (labeled on board) All LEDs and buttons appear to work without state_default. Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in GPL source: https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz * target/linux/ramips/dts/mt7621-rfb-ax-nand.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* image: add additional fields to Netgear encrypted imageWenli Looi2023-07-01
| | | | | | | | | | | | | | | | These fields are used for EAX12 and EX6250v2 series, and perhaps other devices. Compatibility is preserved with the WAX202 and WAX206. In addition, adds the related vars to DEVICE_VARS so that the variables work correctly with multiple devices. References in GPL source: https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz * tools/imgencoder/src/gj_enc.c Contains code that generates the encrypted image. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* mxs: add testing kernel 6.1Zoltan HERPAI2023-07-01
| | | | | | Runtime-tested on Olinuxino Maxi. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* treewide: remove CONFIG_FRAME_WARN from kernel configsRobert Marko2023-07-01
| | | | | | | CONFIG_FRAME_WARN is set dynamically, so there is no need for it to be set in target kernel configs, so lets remove it from all configs. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* generic: filter out CONFIG_FRAME_WARNRobert Marko2023-07-01
| | | | | | | | | | | | | CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the target type dynamically since commit: 16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target"). However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up in multiple target configs during refreshes. So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it ending up in more target configs. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* kernel: bump 5.15 to 5.15.119John Audia2023-07-01
| | | | | | | | Build system: x86_64 Build-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3 Run-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* mxs: rework image generationZoltan HERPAI2023-06-30
| | | | | | | | Migrate to "new" image generation method. Device profiles will be generated based on image/Makefile instead of profiles/ , which will also allow to automatically build images for all supported devices via buildbot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ramips/mt7621: disable the cpufreq driverFelix Fietkau2023-06-30
| | | | | | It causes a noticeable performance decrease Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: net: phy: realtek: fix rtl822x_probe on unsupported devicesMartin Schiller2023-06-27
| | | | | | | | Calling rtl822x_probe() on phy devices which uses the rtl822x_read_mmd() and rtl822x_write_mmd() functions makes no sense and the probe ends with an EOPNOTSUPP error. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Powered by cgit, Themed by Ted Yin.