aboutsummaryrefslogtreecommitdiff
path: root/target/linux
Commit message (Collapse)AuthorAge
* rockchip: enable drivers for rk356xTianling Shen2023-11-26
| | | | | | | Enable all necessary drivers for the rk356x SoCs, including PHY, SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: remove kernel 5.15 patches and configTianling Shen2023-11-26
| | | | | | As we switched to kernel 6.1, these files can go. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: switch to kernel 6.1Tianling Shen2023-11-26
| | | | | | Required by the following rk3568 support. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rockchip: move image generation command to defaultTianling Shen2023-11-26
| | | | | | | | It's applicable for all devices so move it to default to reduce redudant code. Addtionally introduce a new variable `BOOT_SCRIPT` to allow custom boot script (if necessary). Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ipq40xx: enable UBI size checks for some Linksys NAND devicesTony Ambardar2023-11-26
| | | | | | | | Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300, WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved blocks on NAND devices. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* image: use helper function for size unitsTony Ambardar2023-11-26
| | | | | | | | Add the make function 'exp_units' for helping evaluate k/m/g size units in expressions, and use this to consistently replace many ad hoc substitutions like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix typo in Linksys WHW01 image definitionTony Ambardar2023-11-26
| | | | | | | | Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit conversions in build recipes (e.g. 75776k -> 75776*1024). Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for D-link DAP-1720 A1Rani Hod2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa <protectivedad@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com>
* ath79: ar: convert to mac-baseRosen Penev2023-11-25
| | | | | | Replacement for deprecated mac-address-increment Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: ar: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: tp9343: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows getting rid of deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qcn: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows getting rid of deprecated mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qca: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: qca: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: mikrotik: fix dts warningsRosen Penev2023-11-25
| | | | | | property has invalid length Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: nix mac-address-incrementRosen Penev2023-11-26
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621: add interrupt-controllerRosen Penev2023-11-26
| | | | | | | | Fixes dtc warning: '#interrupt-cells' found, but node is not an interrupt provider Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620a: use mac-baseRosen Penev2023-11-26
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620a: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | Allows using mac-base to replace mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7620n: convert to nvmem-layoutRosen Penev2023-11-26
| | | | | | nvmem-cells is deprecated. nvmem-layout allows using mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7628: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7628: use nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow using mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: rtxxxx: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | Deprecated and replaced upstream with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: rtxxxx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-adress-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts and image recipes to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: remove kmod-usb2 for GL-MT6000Chukun Pan2023-11-25
| | | | | | | The usb driver requires kmod-usb3, not kmod-usb2. Remove the useless kmod-usb2 from default package. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: Cetron CT3003: fixes typo for spi propertiesChukun Pan2023-11-25
| | | | | | | Same as commit 3674689, correct 'buswidth' to 'bus-width'. Also move the nmbm properties outside the partition definition. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ipq40xx: remove mac-address-incrementRosen Penev2023-11-25
| | | | | | nvmem-layout allows removal Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Allows replacing mac-address-increment with mac-base. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: fix dtc warnimgRosen Penev2023-11-25
| | | | | | I2C bus unit address format error, expected "62" Signed-off-by: Rosen Penev <rosenp@gmail.com>
* qualcommax: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | nvmem-cells is deprecated Signed-off-by: Rosen Penev <rosenp@gmail.com>
* apm821xx: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | nvmem-cells is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AXHauke Mehrtens2023-11-25
| | | | | | | The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX Fixes: c8c2f522625c ("mediatek: add support for Zbtlink ZBT-Z8102AX") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mt76x8 add support for RTC class/driversXiaobo Liu2023-11-25
| | | | | | This commit adds support for RTC class/drivers to the mt76x8 target. Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com>
* ramips: add support for TP-Link EX220 v1Darlan Pedro de Campos2023-11-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is very similar, if not identical, to the TP-Link AX23 v1 but is targeted at service providers and features a completely different flash layout. Hardware -------- CPU: MediaTek MT7621 DAT RAM: 128MB DDR3 (integrated) FLASH: 16MB SPI-NOR WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax SERIAL: 115200 8N1 LEDs - (3V3 - GND - RX - TX) - ETH ports Installation ------------ Flashing is only possible via a serial connection using the sysupgrade image; the factory image must be signed. You can flash the sysupgrade image directly through the U-Boot console, or preferably, by booting the initramfs image and flashing with the sysupgrade command. Follow these steps for sysupgrade flashing: 1. Establish a UART serial connection. 2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image there. 3. Power on the device and press any key to interrupt normal boot. 4. Load the initramfs image using tftpboot. 5. Boot with bootm. 6. If you haven't done so already, back up all stock mtd partitions. 7. Copy the sysupgrade image to the router. 8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember not to attempt saving settings. Revert to stock firmware ------------------------ Flash stock firmware via OEM web-recovery mode. If you don't have access to the stock firmware image, you will need to restore the firmware partition backed up earlier. Web-Recovery ------------ The router supports an HTTP recovery mode: 1. Turn off the router. 2. Press the reset button and power on the device. 3. When all LEDs start flashing, release reset and quickly press it again. The interface is reachable at 192.168.0.1 and supports installation of the OEM factory image. Note that flashing OpenWrt this way is not possible, as mentioned above. Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
* ramips: Add support for Cudy WR1300 v3Filip Milivojevic2023-11-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7613BE - Switch: 1 WAN, 4 LAN (Gigabit) - Buttons: Reset, WPS - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS - Power: DC 12V 1A tip positive Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common nodes are extracted to .dtsi and new v2 and v3 dts are created. Cudy WR1300 v2 dts now contains ieee80211-freq-limit and has eeprom_factory_8000 length fixed. The same manufacturer's built OpenWRT image is provided for both v2 and v3 devices as a step in installing, but for proper WiFi functionality, a separate build is required. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html Signed-off-by: Filip Milivojevic <zekica@gmail.com>
* mediatek: add Zyxel EX5601-T0 with uboot custom partitionValerio 'ftp21' Mancini2023-11-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The flash procedure is similar to the Xiaomi AX6000 router. Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot: tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb bootm 0x46000000 Load mtd-rw insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1 Format ubi and create ubootenv partitions ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition. If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit. ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb Copy preloader and uboot to /tmp and write them in the mtd mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2 mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip Now write the firmware: sysupgrade -n /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'. Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message: The Power LED was not working correctly and not reacting to the boot process and statuses. The board has space (footprint) for an unpopulated Zigbee chip, while we dont know the device model having this chip populated we have to assure that the common dts doesnt enable interfaces that share pins with such device. In this instance the PCIe and the uart1 and uart2 are disabled. Some of the control PCIE pins seems to be used for the Zigbee chip, UART1 seems to be used as a flash port while UART2 should be the main comunication interface of Zigbee chip. The Zigbee chip should be a EFR32MG21. But the pins used for UART seems to be not on standard PINS used by other adapters. So it cannot run firmwares shared on the web. But it should be possible to build a custom firmware with the corrtect pinmux. This commit also contains the following squashed commit from hitech95 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod Changes and fixes added in common board: - added aliases for boot status leds. - added aliases for the mac-label-device. - added pin claims for core features (MDIO and UART 0) - added default LEDs configuration (01_leds) - added default network configuration (02_network) - added missing kmod-usb3 module for USB3 - fixed LED names - fixed reset pin for SLIC chip - removed unused pinmux configurations and devices - fix LAN (switch) port numbering - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom" - proper factory partition and mac address handling - cleaned up spi_nand sections and partition Changes and fixxes added in stock layout: - added NMBM, if u-boot has it, the kernel must be informed. Co-authored-by: Nicolò Veronese <nicveronese@gmail.com> Co-developed-by: Nicolò Veronese <nicveronese@gmail.com> Signed-off-by: Nicolò Veronese <nicveronese@gmail.com> Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
* mediatek: remove DTS property added by mistakeDaniel Golle2023-11-25
| | | | | | | Remove bogus 'phy-handle = <&phy0>;', an undefined reference. Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Sercomm CPJ routersMikhail Zhilkin2023-11-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Rostelecom RT-FL-1 (Serсomm RT-FL-1) - Rostelecom S1010 (Serсomm S1010.RT) The devices are almost identical and the only difference is one bit in the factory image PID (thanks to Maximilian Weinmann <x1@disroot.org> (@MaxS0niX) for the info and idea to make one PR for two devices at once). Devices specification --------------------- SoC: MediaTek MT7620A, MIPS RAM: 64 MB Flash: 16 MB SPI NOR Wireless 2.4: MT7620 (b/g/n, 2x2) Wireless 5: MT7612EN (a/n/ac, 2x2) Ethernet: 5xFE (WAN, LAN1-4) BootLoader: U-Boot Buttons: 2 (wps, reset) LEDs: 1 amber and 1 green status GPIO leds 5 green ethernet GPIO leds 1 green GPIO 2.4 GHz WLAN led 1 green PHY 5 GHz WLAN led 1 green unmanaged power led USB ports: No Power: 12 VDC, 1 A Connector: Barrel OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Wait until green status led stops blinking (can take several minutes) 4. Login to OpenWrt initramsfs. It's recommended to make a backup of the mtd partitions at this point. 4. Perform sysupgrade using the following command (or use Luci): sysupgrade -n sysupgrade.bin 5. Wait until green status les stops blinking (can take several minutes) 6. Mission acomplished Return to Stock --------------- Option 1. Restore firmware Slot1 from a backup (firmware2.bin): cd /tmp mtd -e Firmware2 write firmware2.bin Firmware2 printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2 reboot Option 2. Decrypt, ungzip and split stock firmware image into the parts, take Slot1 parts (kernel2.bin, rootfs2.bin) and write them: cd /tmp mtd -e Kernel2 write kernel2.bin Kernel2 mtd -e RootFS2 write rootfs2.bin RootFS2 printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2 reboot More about stock firmware decryption: Link: https://github.com/Psychotropos/sercomm_fwutils/ Debricking ---------- Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a recovery image. Link: https://github.com/danitool/sercomm-recovery MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 48:3e:xx:xx:xx:1e | label | | LAN | 48:3e:xx:xx:xx:1e | label | | WAN | 48:3e:xx:xx:xx:28 | label+10 | | WLAN 2g | 48:3e:xx:xx:xx:20 | label+2 | | WLAN 5g | 48:3e:xx:xx:xx:24 | label+6 | +---------+-------------------+-----------+ Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: mt7620: drop unnecessary trailing tabsMikhail Zhilkin2023-11-25
| | | | | | Let's tidy up a bit (drop unnecessary trailing tabs). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: sercomm.mk: make common recipe to set a bit in pidMikhail Zhilkin2023-11-25
| | | | | | | | This commit makes a common recipe to set bit in Sercomm factory pid since this is necessary for several devices (WiFire S1500.nbn, Rostelecom RT-FL-1) at different offsets. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ipq40xx: refresh patchesRobert Marko2023-11-25
| | | | | | CI reported that ipq40xx needed a refresh, so lets refresh it. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mediatek: add support for Zbtlink ZBT-Z8102AXDaniel Golle2023-11-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 1024MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 4 LAN (Gigabit) USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by Ian Ishmael C. Oderon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: 6.1: backport upstream Aquantia PHY firmware loader patchesChristian Marangi2023-11-24
| | | | | | | | | | | | Backport merged upstream patch that adds support for firmware loader from NVMEM or attached filesystem for Aquantia PHYs. Refresh all kernel patches affected by this change. Also update the path for aquantia .ko that got moved to dedicated directory upstream. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: convert to nvmem-layoutRosen Penev2023-11-24
| | | | | | nvmem-cells is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 5.15 to 5.15.139John Audia2023-11-23
| | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.139 Removed upstreamed: backport-5.15/830-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch[1] backport-5.15/830-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch[2] x86/patches-5.15/120-hwrng-geode-fix-accessing-registers.patch[3] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=aec3706971b332af8321b2beccba981b8061489a 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=893eedf596dd81c7a7f0cd80b345956ae000eab9 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=a5c83c8043d70b9a28d1bd78a2dbbab340f43889 Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.63John Audia2023-11-23
| | | | | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.63 Removed upstreamed: generic/backport-6.1/815-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch generic/backport-6.1/815-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch ixp4xx/patches-6.1/0007-watchdog-ixp4xx-Make-sure-restart-always-works.patch Manually rebased: bcm27xx/patches-6.1/950-0606-hwrng-bcm2835-sleep-more-intelligently.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=7d0e60e4ff840e97fb18afb2a7344442c10a6fdf 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=63cdeb20ee3bfef820b045b8d3b8395f9f815a74 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=8803da01fe1b4ca3d37745283f7e73c6c2558c0c Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
Powered by cgit, Themed by Ted Yin.