summaryrefslogtreecommitdiff
path: root/target/linux/ramips/base-files/etc/board.d
Commit message (Collapse)AuthorAge
* ramips: Correct switch configuration for Newifi D1Chuanhong Guo2017-02-13
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Added Onion Omega2 and Omega2+Lazar Demin2017-01-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io>
* ramips: add support for VoCore2Andrew Yong2017-01-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: MiWiFi Nano fixesL. D. Pinney2017-01-02
| | | | | | | | | | | | | | | | Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use D-Link DIR-600 B1 image for B2 versionMathias Kresin2016-12-24
| | | | | | | Everything set for the B1 is identical to the values uses for the B2 version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use destinct 11AC NAS board nameMathias Kresin2016-12-24
| | | | | | | | | | Use a distinct board name even if the board is near to identical to the WeVO W2914NS v2. To make sure that a 11AC NAS image can not be installed on a WeVO W2914NS v2, both board need to use different names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-22
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-22
| | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: Fix led init script for Lenovo Y1/Y1sBangLang Huang2016-12-04
| | | | | | | This commit fix the led init script for Lenovo Y1 and Y1S due to the manual and dts file. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: fix LAN port order of WeVO W2914NS v2Yong-hyu, Ban2016-12-04
| | | | Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
* ramips: improve F5D8235 V1 supportTobias Wolf2016-12-04
| | | | | | | | | | | | | | | | | | | This fixes the partition name for the firmware splitter, the cfi address and adds the mtd-eeprom address for wmac. It adds additional LEDs and make use of them in diag.sh and 01_leds. Please note that the ":blue:wired" LED is used because the ":blue:router" behaviour is unpredictable for failsafe indication. The issue with the router LED is that you have two states only. "off" is steady on and "on" blinks. Therefore the wired LED is more suitable. Furthermore it reuses the correct switch configuration definition to reflect the device ports and numbering. Additionally fixes the issue that the default configuration is not applied as no port 6 exists on this device. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: add support for WeVO W2914NS v2perillamint2016-11-21
| | | | Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-18
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Sitecom WLR-6000Jasper Scholte2016-11-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the file is way to big for only including a kernel. The factory image need to have the dlf file extension. Otherwise the Sitecom firmware rejects the file. The stock firmware uses the following mac addresses: LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr) 2,4: 00:0C:F6:AA:BB:D8 (EEPROM) 5: 00:0C:F6:AA:BB:DC (EEPROM) WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr) Assuming the mac address range :D8 to :DC is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: 2.4GHz: 00:0C:F6:AA:BB:D8 LAN: 00:0C:F6:AA:BB:D9 WAN: 00:0C:F6:AA:BB:DA 5 GHz: 00:0C:F6:AA:BB:DC The first MAC is assigned to the 2.4GHz WiFi interface to keep compatibility with the SSIDs printed on the case, which have the last three sextets of the MAC address appended. There are still issues with the rt2x00 driver. It is not possible to use both wireless interfaces at the same time. The 2.4 GHz wireless (PCIe) only works if the internal 5GHz wireless is/has been enabled or used for scanning. The internal 5GHz wireless only works if the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz after it was enabled will result in stations seeing the 5Ghz AP but are unable to connect. Due to the not optimal working wifi the manufacture, backup and storage partitions of the OEM firmware are kept for now to allow an easy switch back to the Sitecom firmware. Signed-off-by: Jasper Scholte <NightNL@outlook.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Digineo AC1200 ProDominik Menke2016-11-17
| | | | | | This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash. Signed-off-by: Dominik Menke <dom@digineo.de>
* ar71xx, ramips: reduce CPU load and flickering on devices using rssliedsMartin Weinelt2016-11-16
| | | | | | | | | Polling every 40ms causes more than 10% CPU load on weak devices. An interval of 200ms is much more reasonable. Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net> [Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message] Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: add port index in switch config for buffalo WHR-* and WSR-* devicesFelix Fietkau2016-11-14
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: Add support for Wavlink WL-WN575A3Roger Pueyo Centelles2016-11-08
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug wireless router with the following specifications: - CPU: MediaTek MT7628AN 580MHz - Flash: 8MB - RAM: 64MB - Ethernet: 2x 10/100 Mbps (switched) - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm - Antennas: 4x external (2 per radio), non-detachable - LEDs: 4 programmable + LAN, WAN, POWER - Buttons: reset, WPS Flashing instructions: Factory U-boot launches a TFTP client if WPS button is pressed during power-on. Rename the sysupgrade file and configure a TFTP as follows: - Client (WL-WN575A3) IP: 192.168.10.101 - Server IP: 192.168.10.100 - Filename: firmware.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for MikroTik hEX v3 (RB750Gr3)Andrew Yong2016-11-02
| | | | | | | | | | | | | | The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz). RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot. Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware. The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices. A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware. Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: Archer C50 cleanupHenryk Heisig2016-10-31
| | | | | | | | | | | - setting read-only flag to important partitions - enabling PA to improve 2.4 GHz signal strength - add missing leds - rename colour led - add mac adress to 5GHz wlan interface - included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h> Signed-off-by: Henryk Heisig hyniu@o2.pl
* ramips: fix PSG1218 LEDsXuefu Lin2016-10-26
| | | | Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: add support for Planex VR500.YuheiOKAWA2016-10-15
| | | | | | | | | | | | SOC: MT7621A RAM: 256MiB NOR: MX25L51245G Non Wireless Router. Issue: soft reboot problem. SPI Flash do not exit 4byte address mode. Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
* ramips: improve edimax 6200n/nl supportMathias Kresin2016-10-15
| | | | | | | | | | Assign the reset functionality to the wps/reset buttons. Use the wlan switch of the 6200n to enable/disable wlan. Add the internet led of the 6200nl and use the led for boot status indication Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix edimax 6200nl switch configMathias Kresin2016-10-15
| | | | | | | | | | | | | With 3a9752bbd2bc00e407b5dcad21789720f40abf0e and later changes to ramips_set_preinit_iface() the default vlan config applied during preinit was changed. These changes were made without updating the default network config to ensure that vlan interfaces used for lan/wan are still configured. Fix the issue by using the default all LAN portmap and disabling not connected switch ports using portdisable device tree parameter. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: tag the CPU switch portMathias Kresin2016-10-15
| | | | | | | | | | | | With de5102651501e51c036f88fe9c4dbf6974e5158a the explicit tagging of the CPU port was removed. This leads to a not working default network config, with vlans enabled but disabled CPU tagging, for boards where all switch ports are having the same role. In case the ports are having different roles set, tagging is is set implicit for the CPU port by ucidef_add_switch(). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: remove fixed lan/wan interface for switch configsMathias Kresin2016-10-15
| | | | | | | | | | Don't set the lan/wan interface when using ucidef_add_switch. This results into a wan interface albeit all ports a annotated as lan ports. ucidef_add_switch takes care of setting the correct lan/wan interface according to the annotation of the ports. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Zyxel NBG-419N2 (WAP3205v2)Klaus2016-10-04
| | | | | | | | | | | applied bb-final-ramips-add-zyxel-nbg-419n2.patch from 123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65; see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905, modified slightly to fit to CC release and to new lede build system: image/rt305x.mk include file is used now changed NBG-419N2.dts format to fit style of other dts files Signed-off-by: Klaus <k-laus@quantentunnel.de>
* ramips: Add support for Phicomm K2 PSG1218Xuefu Lin2016-10-04
| | | | | | | | | - CPU: MT7620A 580MHz - Flash: 8MB - RAM: 64MB - External PA+LNA on both WLAN2.4 and WLAN5 - 4x LAN ethernet and 1x WAN ethernet Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: Xiaomi MiWiFi Nano: fix status ledCezary Jackiewicz2016-09-29
| | | | | | | - add status led for Xiaomi MiWiFi Nano - revert https://github.com/lede-project/source/commit/af1e70b4a730e91ce1668d506ebc5c1c8cf5abf5 , this should not be added. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips : add support for Newifi D1BangLang Huang2016-09-27
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips : add support for PandoraBox D1BangLang Huang2016-09-27
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: Add support for ZBT-CPE102Cezary Jackiewicz2016-09-27
| | | | | | | | | | - CPU: MT7620N 580MHz - Flash: 8MB - RAM: 64MB - build-in minipcie slot for modem 3G/4G - one ethernet port 10/100Mbps Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-10
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: board.d merge redundant switch/interface configsMathias Kresin2016-09-10
| | | | | | Fix alphabetical order distortions as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Mercury MAC1200R v2Daniel Golle2016-09-09
| | | | | | | | MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM reset button GPIO is still missing (anyone?) bootloader password is 'slp' Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: TEW-691GR: fix switch and wirelessMathias Kresin2016-08-20
| | | | | | | | | Due to the missing phy-mode setting, the switch wasn't initialised. The wireless requires an eeprom to work. Use the same mac addresses as the stock firmware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: TEW-692GR: fix switch and wirelessMathias Kresin2016-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AR8327 initvals were not copied to the DTS during the switch from mach file to device tree and broke the switch on the device. The former used PORT6 related initvals were wrong and have been corrected. The phy mode setting for the switch was missing in the DTS as well. The wireless requires an eeprom to work. The dual band wireless chips have both bands enabled by default but only one band per chip is working. The stock firmware uses the following mac addresses: LAN: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 5 GHz: AA:BB:CC:DD:EE:E8 Assuming the mac address range :E4 to :E8 is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: LAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E5 5 GHz: AA:BB:CC:DD:EE:E8 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support for Thunder TimecloudChuanhong Guo2016-08-10
| | | | | | | Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an SD Card slot. There is no wireless cards. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Add support for TEW-714TRUJimmy Zhong2016-08-10
| | | | Signed-off-by: Jimmy Zhong <mb300sd@mb300sd.net>
* ramips: Rename TP-Link Archer C50 LEDsP.Wassi2016-07-26
| | | | | | | Rename LEDs in TP-Link Archer C50 from [manufacturer name] to [board name] ("tp-link" -> "c50") Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: Improve TP-Link Archer C20i supportP.Wassi2016-07-26
| | | | | | Improve / finalise TP-Link Archer C20i support. Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: unify etc/board.d/01_leds configurationP.Wassi2016-07-24
| | | | | | | Introduce an optional parameter at the local set_usb_led and set_wifi_led function such that they can take a triggering device. If no parameter is passed, behaviour is unchanged. Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: remove indentation in etc/board.d/01_ledsPaul Wassi2016-07-24
| | | | | Remove indentation at end of line in base-files/etc/board.d/01_leds Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ramips: Add support for D-Link DCH-M225Michael Lee2016-07-11
| | | | | | | | D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash, 3.5mm audio out support. but no ethernet and usb ports. so you must default enable wifi. Signed-off-by: Michael Lee <igvtee@gmail.com>
* ramips: Add support for the NixCore X1 ModuleL. D. Pinney2016-07-11
| | | | | | | | | The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module. http://nixcores.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Acked-by: Drew Gaylo <drew@nixcores.com>
* ramips: fix buffalo wmr-300 lan portJohn Crispin2016-07-05
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: set correct LAN/WAN MAC addresses on DIR-860L B1Matthias Schiffer2016-06-30
| | | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add button support and make LEDs known to userspace for DIR-860L B1Matthias Schiffer2016-06-30
| | | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add suport for ZBT APE522IIRoger Pueyo Centelles2016-06-22
| | | | | | | | | The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has 64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with 802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac MT7612E-based 5 GHz radio. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips/base-files: Add support for Archer C50Henryk Heisig2016-06-13
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Powered by cgit, Themed by Ted Yin.