aboutsummaryrefslogtreecommitdiff
path: root/target/linux/qualcommax
Commit message (Collapse)AuthorAge
...
* qualcommax: mark upstreamed patches as suchRobert Marko2023-10-29
| | | | | | The GPLL fixes were merged upstream, so lets mark them as such. Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq807x: add support for Netgear WAX630Kristian Skramstad2023-10-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz * RAM: 1 GiB of DDR3 466 MHz * Flash: NAND 512 MiB (Winbond W29N04GZ) * 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L * UART: One 4-pin populated header next to the heatsink and a chip. GND RXD TXD, beginning from the external antennas. 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at * One 100/1000 Gigabit Ethernet Wlan: * 4x4 in 2.4GHz : 802.11b/g/n/ax * 4x4 in 5.0GHz L: 802.11a/n/ac/ax * 4x4 in 5.0GHz H: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H) Power: * 802.3bt/at 30.1W * DC 12V/3.5A Mounting: Wall and ceiling ``` ``` 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to the console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* qualcommax: ipq807x: alphabetically sort Netgear WAX family.Kristian Skramstad2023-10-28
| | | | | | | | | | | | | As requested by the maintainers, the order for the WAX family should be alphabetically. WAX620 is now after WAX218. Files changed: +ipq807x.mk +01_leds No changes to the content. Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* qualcommax: ipq8074: use upstreamed CPUFreq NVMEM supportRobert Marko2023-10-16
| | | | | | | | | | IPQ8074 CPUFreq NVMEM support has finally landed upstream, so lets use the upstreamed version. This has a benefit of also supporting IPQ8174 (Oak) family for which SMEM SoC ID-s were also upstreamed. Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: add pending GPLL parent fixesRobert Marko2023-10-15
| | | | | | | | | | | | | | | | | | | | SBL will configure IPQ807x cores to boot at 800MHz as a safe default frequency that is provided by GPLL0, but GPLL0 is not currently configured as a possible parent in the APSS clock driver not being passed to it via DTS which will then cause the kernel to not properly identify the current CPU frequency during booting and will think that CPU is currently at XO frequency of 19.2MHz instead of 800MHz cores are actually at and print: cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 19200 KHz, changing to: 1017600 KHz So, lets import patches pending upstream to prevent GPLL scaling and feed the GPLL0 clock to APSS clock driver so we get: cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz This is mostly cosmetic fix, but with all of the possible SBL and FW versions there could be edge cases resolved by this and not scaling GPLL-s anymore. Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: bump 6.1 to 6.1.57John Audia2023-10-14
| | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.57 Manually rebased: generic/pending-6.1/702-net-ethernet-mtk_eth_soc-enable-threaded-NAPI.patch Removed upstreamed: qualcommax/patches-6.1/0134-PCI-qcom-Fixing-broken-pcie-enumeration-for-2_3_3-co.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.57&id=2dfb5f324d799f4545e17631415aba6d302a8e2b Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: John Audia <therealgraysky@proton.me>
* ipq807x: add support for Netgear WAX620Kristian Skramstad2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz * RAM: 1 GiB of DDR4 600 MHz * Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC) * 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz * UART: Two 4-pin unpopulated headers under the LEDs. Use the header closest to LED 4 and 5. They are marked with a white stroke. TX RX GND, beginning from "4". 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081) Wlan: * 4x4 in 2.4GHz: 802.11b/g/n/ax * 4x4 in 5.0GHz: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz) Power: * PoE+ 802.3at/af 25.5W * DC 12V 2.5A ``` ``` Note: The OpenWrt image is setup with DHCP and not a static IP. 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* kernel: backport v6.6 nvmem changesRafał Miłecki2023-08-31
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq807x: add support for Netgear RAX120v2Thomas Kupper2023-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
* qualcommax: remove upstreamed TRIM quirksRobert Marko2023-08-10
| | | | | | | | | | | | | | TRIM disable quirks for eMMC-s were merged upstreamed and backported to stable in 6.1.39, however they were not dropped during the kernel update and quilt is not complaining at all. So, lets manually remove them as they are part of 6.1.39 [1] [2]. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/mmc/core/quirks.h?h=v6.1.39&id=182bf07a24c4c1022bf83c90be619d60427745c3 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/mmc/core/quirks.h?h=v6.1.39&id=69bc3203513c4fcd6ca84b0185de454bacf87883 Fixes: fec22f8375b4 ("kernel: bump 6.1 to 6.1.39") Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: refresh kernel configRobert Marko2023-08-10
| | | | | | Refresh the kernel config to keep in sync with the generic one. Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq807x: fix Gen2 PCIe portRobert Marko2023-07-31
| | | | | | | | | | | | | | Gen2 PCIe port recently got broken on IPQ807x during update to 6.1.39 as upstream backported: ("PCI: qcom: Remove PCIE20_ prefix from register definitions") [1] So, fix it by adding a pending upstream fix for it [2]. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/pci/controller/dwc/pcie-qcom.c?h=v6.1.39&id=db962c7a711c3393a80a18219960cd54fb33c53d [2] https://patchwork.kernel.org/project/linux-arm-msm/patch/20230724063429.3980462-1-quic_srichara@quicinc.com/ Fixes: fec22f8375b4 ("kernel: bump 6.1 to 6.1.39") Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq807x: prpl-haze: fix sysupgrade flashing from bootloaderPetr Štetiar2023-07-28
| | | | | | | | | | | | | | | | | | | | While flashing sysupgrade image from U-Boot, then the rootfs_data overlay filesystem formatting is left for the fstools during firstboot, but that wont work as mkfs.f2fs is missing in the sysupgrade image: mount_root: overlay filesystem in /dev/loop0 has not been formatted yet mount_root: no usable overlay filesystem found, using tmpfs overlay sh: mkfs.f2fs: not found Filesystem Size Used Available Use% Mounted on /dev/loop0 139.6M 46.9M 92.6M 34% /overlay Number Start (sector) End (sector) Size Code Name 20 98850 406349 150.1 MiB FFFF rootfs So lets fix it by adding f2fs support to the sysupgrade image. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 6.1 to 6.1.40John Audia2023-07-25
| | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-6.1/701-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1] generic/pending-6.1/160-workqueue-fix-enum-type-for-gcc-13.patch[2] qualcommax/patches-6.1/0022-v6.5-soc-qcom-mdt_loader-Fix-unconditional-call-to-scm_pa.patch[3] Manually rebased: bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch bcm53xx/patches-6.1/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=685b57a1221c38ec8b456f968264d2496715820c 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=2d57a1590f4d8c516f5aaf8fd5bb4f52d67275d8 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=33f8dff6e1cbba5c2ec85fa5649c0a759a7e685c Build system: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod Build-tested: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.39John Audia2023-07-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-6.1/803-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[1] generic/pending-6.1/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[2] bcm27xx/patches-6.1/950-0034-drm-bridge-Introduce-pre_enable_upstream_first-to-al.patch[3] bcm27xx/patches-6.1/950-0439-nvmem-Use-NVMEM_DEVID_AUTO.patch[4] bcm4908/patches-6.1/040-mtd-parsers-refer-to-ARCH_BCMBCA-instead-of-ARCH_BCM.patch[5] bcm53xx/patches-6.1/031-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[6] bcm53xx/patches-6.1/031-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[7] mediatek/patches-6.1/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch[8] qualcommax/patches-6.1/0008-v6.2-clk-qcom-reset-support-resetting-multiple-bits.patch[9] Manually rebased: bcm27xx/patches-6.1/950-0035-drm-panel-Add-prepare_upstream_first-flag-to-drm_pan.patch bcm27xx/patches-6.1/950-0404-drm-panel-panel-ilitek9881c-Add-prepare_upstream_fir.patch bcm27xx/patches-6.1/950-0699-Bluetooth-hci_sync-Add-fallback-bd-address-prop.patch mediatek/patches-6.1/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ab0bd172d6289310a05a0cd15e1432e828d386ae 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=6df680709d901346831ef8f221cc90a42062c526 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=5044e5f2511c9afdf9880d2bb6b9d37dfc345dac 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=e27948f329f7e02591ed1feb9a7710c2ccf89a83 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ad2928e7f3f6120a0bd18aa1056b3b24068027c5 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=2b55a985727833f37c39911f34096b3fdf2a367d 7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=90d4c487cd658b51212eb65ae804ab11af193672 8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=7e3ee25e8c7c7be1eacdfc6d9f5f0e550a2af241 9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=b20854ef6c4955be3310975a72f02d92cb01d6d4 Build system: x86/64 Build-tested: x86/64 Run-tested: x86/64 Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de> Co-authored-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: John Audia <therealgraysky@proton.me> [ rebase bcm27xx and mediatek patches, refresh commit description ] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> [ minor fixup to bcm27xx patches, refresh commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: migrate FORCE_MAX_ZONEORDER to ARCH_FORCE_MAX_ORDER for 6.1Stefan Kalscheuer2023-06-25
| | | | | | | | | | The flag FORCE_MAX_ZONEORDER was renamed to ARCH_FORCE_MAX_ORDER in Kernel 6.1 [1]. Rename the flag in generic Kconfig and remove it from target configs. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=0192445cb2f7ed1cd7a95a0fc8c7645480baba25 Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* qualcommax: ipq807x: use upstreamed thermal trips patchRobert Marko2023-06-17
| | | | | | | Critical thermal trips patch got merged upstream, so use the upstreamed patch and mark it as backport along with the future 6.5 kernel version. Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq807x: include BDF for Compex WPQ873Robert Marko2023-06-16
| | | | | | | | | Currently, Compex WPQ873 images are not including the ath11k BDF-s at all and this means that there is no WLAN support, so lets include the BDF as its already packaged. Fixes: 07c45c085908 ("ipq807x: add support for Compex WPQ873") Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: move ipq807x support to subtargetRobert Marko2023-06-16
| | | | | | | | | | | | Now that qualcommax exists as a target and dependencies have been updated let move ipq807x support to subtarget of qualcommax. This is mostly copy/paste with the exception of having to update SSDK and NSS-DP to use CONFIG_TARGET_SUBTARGET. This is a preparation for later addition of IPQ60xx and IPQ50xx support. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq807x: rename target to qualcommaxRobert Marko2023-06-16
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s. However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid duplicating kernel patches and everything lets make a common target with per SoC subtargets. Start doing that by renaming ipq807x to qualcommax so that dependencies on ipq807x target can be updated. Signed-off-by: Robert Marko <robimarko@gmail.com>
Powered by cgit, Themed by Ted Yin.