aboutsummaryrefslogtreecommitdiff
path: root/target/linux/mediatek
Commit message (Collapse)AuthorAge
...
* mediatek: fixes typo for spi propertiesChukun Pan2024-01-14
| | | | | | Same as commit 3674689, correct 'buswidth' to 'bus-width'. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: YunCore AX835: convert to nvmem-layoutChukun Pan2024-01-14
| | | | | | | The nvmem-cells is deprecated. Also simplify mac address settings. Fixes: b4086f4 ("mediatek: add support for YunCore AX835") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: Cudy WR3000: simplify mac address setupChukun Pan2024-01-14
| | | | | | | | The mac address of the network port under the switch is the same as the corresponding gmac by default, so there is no need to repeat the setting. Compile test only. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: Cetron CT3003: move mac address setup to dtsChukun Pan2024-01-14
| | | | | | | It looks like we can put the mac address setting into the device tree. Compile test only. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: refresh kernel configChukun Pan2024-01-14
| | | | | | | Refresh kernel config with 'make kernel_oldconfig'. Also disable the useless rtl8367s gsw driver. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: mt7622: refresh kernel configChukun Pan2024-01-14
| | | | | | Refresh kernel config with 'make kernel_oldconfig'. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: fix BPI-R3 wifi mac addressFelix Fietkau2024-01-09
| | | | | | | | Setting/clearing bits on the first byte of the mac address causes collisions when using multiple SSIDs on both PHYs. Change the allocation to alter the last byte instead. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: disable btif for mt7622 devicesFelix Fietkau2024-01-09
| | | | | | It breaks built-in SoC WLAN. Can be re-enabled after we've figured out the cause Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add support for YunCore AX835Leon M. Busch-George2024-01-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 16MB NOR RAM: 256MB Ethernet: 2x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset Power: DC 12V 1A, PoE 802.3af 48V Flash instructions: Option #1 - SSH I was able to SSH into the stock firmware of my device. 1. Attach the router to the network 2. Use scp (-O) to copy the sysupgrade image 3. Connect using SSH and run `sysupgrade -n` Option #2 - U-Boot One way to use the bootloader for flashing is using TFTP: 1. Connect to the router using an ethernet cable 2 Spin up a TFTP server serving the sysupgrade file 3. Open the case and attach a UART 4. Attach power to the router and interrupt the countdown by pressing any key 5. Select option #2 (Upgrade firmware) 6. Enter IP address information and image name 7. Wait patiently Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net> Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
* mediatek: GL-MT6000: Add missing LED state definitionsHannu Nyman2024-01-09
| | | | | | | | | | | | | | | | | | | | Adjust LED names and provide the OpenWrt status indicator aliases to actually use LEDs by the OpenWrt boot & sysupgrade processes. * Name both LEDs clearly by the color * Add the missing OpenWrt LED status indicator aliases and remove the now unnecessary default status from blue LED After this commit, the LEDs are used as: * bootloader, really early Linux boot: blue LED is on * preinit/failsafe: white LED blinks rapidly * late boot: white LED blinks slowly * boot completed, running normally: blue LED is on * sysupgrade: white LED blinks Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* mediatek: filogic: add support for Xiaomi AX3000TDim Fish2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **SoC**: MediaTek MT7981B 2x A53 **Flash**: ESMT F50L1G41LB 128MB **RAM**: NT52B128M16JR-FL 256MB **Ethernet**: 4x 10/100/1000 Mbps **Switch**: MediaTek MT7531AE **WiFi**: MediaTek MT7976C **Buttons**: Reset, Mesh **Power**: DC 12V 1A 1. Get ssh access. Supported stock firmware **1.0.47** ``` curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A ``` 2. Backup stock partitions ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then transfer them to your computer in a safe place. 3. Get firmware information `cat /proc/cmdline` 4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash If **firmware=0** ``` ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` If **firmware=1** ``` ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` Then reboot your router, it should boot to the OpenWrt initramfs system now. 5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin` 1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` `reboot` 2. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 3. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 4. *(Optional **-10Mb** free space) Add recovery boot feature.* ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb ``` 5. Flash Openwrt U-Boot ``` mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2 mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP ``` 6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb` 1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock images from backup ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Signed-off-by: Dim Fish <dimfish@gmail.com>
* kernel: bump 6.1 to 6.1.71John Audia2024-01-06
| | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.71 Manually rebased: gemini/patches-6.1/0002-usb-fotg210-Collect-pieces-of-dual-mode-controller.patch All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.146John Audia2024-01-06
| | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.146 Removed upstreamed: generic/hack-5.15/940-ksmbd-have-a-dependency-on-cifs-arc4.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.146&id=ac385518598f50dd1b9b41bd05f50ce9795481d5 Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: MERCUSYS MR90X v1: remove deprecated led "label" propertiesMikhail Zhilkin2024-01-06
| | | | | | | | | | | This commit: 1. Removes deprecated "label" property from the dts leds subnnodes; 2. Updates "01_leds" script. Link: https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml Link: https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/leds-gpio.yaml Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* mediatek: Add support for D-Link EAGLE PRO AI R32Roland Reinl2024-01-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | R32 is like the M32 part of the EAGLE PRO AI series from D-Link. Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 2 LEDs (Status and Internet, both can be either orange or white) - 2 buttons (WPS and Reset) Compared to M32, the R32 has the following differences: - 4 LAN ports instead of 2 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001 - Individual LEDs for power and internet - MAC address is stored at another offset in the ODM partition MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x81 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment. The support for the M32/R32 already includes support for flashing from the OEM web interface: - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap) Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* mediatek: filogic: Asus TUF AX6000 fix inverted LED for 2.5Gb LAN portPatryk Kowalczyk2024-01-02
| | | | | | | | Router Asus TUF AX6000 have second MaxLinear GPY211 PHY controller for 2.5Gb LAN port. The 5'th LAN port have inverted status of the LED. Based on the commit from main branch 90fbec8 we could set proper status of the LED. Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
* mediatek: filogic: add support ASUS RT-AX59UXavier Franquet2023-12-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (based on support for ASUS RT-AX59U by liushiyou006) SOC: MediaTek MT7986 RAM: 512MB DDR4 FLASH: 128MB SPI-NAND (Winbond W25N01GV) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: MediaTek MT7531 Switch UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Upgrade from AsusWRT to OpenWRT using UART Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin. Connect the PC with TFTP server to the RT-AX59U. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0) Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.70 $ tftpboot 0x46000000 rtax59u.bin $ bootm 0x46000000 Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Upgrade from AsusWRT to OpenWRT using WebUI Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file Wait for OpenWRT to boot (192.168.1.1). Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT. We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g when bit 28 is already set. : Stock : OpenWrt WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4 WLAN 2g (2) : : CA:xx:xx:0D:xx:D4 WLAN 2g (3) : : CE:xx:xx:0D:xx:D4 WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5 WLAN 5g (2) : : CE:xx:xx:1D:xx:D5 WLAN 5g (3) : : C2:xx:xx:1D:xx:D5 WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE WLAN 2g (2) : : 0A:xx:xx:76:xx:BE WLAN 2g (3) : : 0E:xx:xx:76:xx:BE WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF WLAN 5g (2) : : 0E:xx:xx:76:xx:BF WLAN 5g (3) : : 02:xx:xx:76:xx:BF Signed-off-by: Xavier Franquet <xavier@franquet.es>
* mediatek: filogic: reorder nodes in mt7988a.dtsiRafał Miłecki2023-12-29
| | | | | | | | Use order described as preferred in DTS Coding Style: 1. Sort bus nodes by unit address 2. Use alpha-numerical order for the rest Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: add support for Routerich AX3000Mikhail Zhilkin2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR is continuation of work under "mediatek: add support for Routerich AX3000" #13703 by the agreement with PR #13703 original author (Maximilian Weinmann <x1@disroot.org>). All reviews from the previous PR were taken into into account. Routerich AX3000 is a wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 256 MiB (ESMT M15T2G16128A) - Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MIMO 2x2 - 5 GHz : a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE) - USB : 1x 2.0 - UART : through-hole on PCB - [J500] GND, TX, RX, 3.3V (115200n8) - Buttons : Mesh, Reset - LEDs : 1x Power (Blue) 1x WiFi 2.4 GHz (Blue) 1x WiFi 5 GHz (Red) 1x Mesh (Blue) 3x LAN activity (Blue) 1x WAN activity (Blue) 2x WAN no-internet (Red) - Power : 12 VDC, 1.5 A Installation ------------ Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface (without keeping settings). Return to stock --------------- Install stock firmware image (without keeping settings) using OpenWrt sysupgrade method. Recovery -------- Connect uart, use u-boot menu to flash stock firmware image or boot OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:b4 | label | | LAN | 24:0f:5e:xx:xx:b5 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* mediatek: add support for Zbtlink ZBT-Z8103AXIan Oderon2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND No. of Antennas: 6 Note: Upon opening the router, only 5 antennas were connected to the mainboard. Led Layout: Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi Buttons: Reset-Mesh Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Signed-off-by: Ian Oderon <ianoderon@gmail.com>
* mediatek: enable mt7981-wo-firmware package by defaultRobert Senderek2023-12-25
| | | | | | | | | Add support for wireless offload package in default configuration for -Cudy WR3000 -Confiabits MT7981 For some reason those ware missing. I confirm this work for my Cudy WR3000 Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
* kernel: bump 5.15 to 5.15.143John Audia2023-12-19
| | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.143 Removed upstreamed: generic/backport-5.15/795-v6.6-12-r8152-Rename-RTL8152_UNPLUG-to-RTL8152_INACCESSIBLE.patch[1] Manually rebased: mediatek/patches-5.15/100-dts-update-mt7622-rfb1.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.143&id=00beca907a7be61da935bb687f9601420fc5f8a8 Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.68John Audia2023-12-19
| | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.68 Removed upstreamed: generic/backport-6.1/795-v6.6-12-r8152-Rename-RTL8152_UNPLUG-to-RTL8152_INACCESSIBLE.patch[1] Manually rebased: mediatek/patches-6.1/100-dts-update-mt7622-rfb1.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.68&id=3759e735562a31e44fee825498f05c06e64b25a8 Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.66John Audia2023-12-12
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.66 All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: bananapi-r3: add overlay for ReSpeaker 2-mic hatDaniel Golle2023-12-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DT overlay to allow using the ReSpeaker 2-mic hat connected to the 26-pin header of the BananaPi BPi-R3. Supported sample formats: S16_LE, S24_LE, S32_LE Supported sample rates: 8/12/16/24/32/48/96/192 kHz | BPi-R3 | ReSpeaker 2-mic Signal | 26-pin | 40-pin ----------+----------+------------------- VCC 5V | 2 | 2 I2C SDA | 3 | 3 I2C SCL | 5 | 5 GND | 6 | 6 PCM CLK | 12 | 12 PCM FS | 15 | 35 PCM DIN | 26 | 38 GND | 25 | 39 PCM DOUT | 22 | 40 Once connected, install the driver and tell U-Boot to apply the DT overlay: opkg kmod-sound-soc-mt7986-wm8960 fw_setenv bootconf_base "config-mt7986a-bananapi-bpi-r3#mt7986a-bananapi-bpi-r3-respeaker-2mics" reboot To setup the ReSpeaker for Stereo out on the Headphone plug: amixer sset 'Right Output Mixer PCM' on amixer sset 'Left Output Mixer PCM' on amixer sset 'PCM Playback -6dB' off amixer sset 'O018 I150_Switch' on amixer sset 'O019 I151_Switch' on amixer sset 'O124 I032_Switch' on amixer sset 'O125 I033_Switch' on amixer sset 'Headphone' 121 amixer sset 'Playback' 255 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: backport MT7986 audio driverMaso Huang2023-12-11
| | | | | | | | Pick commits adding drivers for audio engine found in MT7986 from Linux 6.6 as well as follow-up fixes from Linux 6.7. Signed-off-by: Maso Huang <maso.huang@mediatek.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Adtran SmartRG Bonanza Peak seriesDaniel Golle2023-12-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s Wi-Fi 6 residential gateway, access point and mesh router products. All of them come with an eMMC to boot from, are powered via USB-C and got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531 Bluetooth module connected via UART. If the device was previously running stock firmware, the BT chip's internal flash has been loaded with firmware and it can be attached using hciattach when using OpenWrt. SOC: MediaTek MT7986A RAM: 2 GiB DDR4 eMMC: 8 GiB Bluetooth: BLE5 (DA14531) Serial: 3.3V level, 115200 8n1 on 4-pin connector * SDG-8612 - Dual-band RJ-45 gateway 2x 2.5G MaxLinear PHY for WAN port 3x 1GE LAN ports via MT7531 switch * SDG-8614 - Dual-band SFP gateway 1x SFP cage with up to 2.5G speed 1x 2.5G MaxLinear PHY for LAN port 3x 1GE LAN ports via MT7531 switch * SDG-8622 - Tri-band mesh router 2x 2.5G MaxLinear PHY The MT7986 2G and 5G are used as 2G and 5G high band. There’s a MT7915 PCIe card for 5G low band. * SDG-8632 - Tri-band mesh router with 6 GHz 2x 2.5G MaxLinear PHY The MT7986 serves the 2G and 6G bands. There’s a MT7915 PCIe card for 5G. Installation via U-Boot serial console: 0. setup TFTP server with IP 192.168.1.10/24, place initramfs image renamed to openwrt.XXX where XXX is the internal product number: SDG-8612: XXX = 412 SDG-8614: XXX = 414 SDG-8622: XXX = 422 SDG-8632: XXX = 432 1. connect to the serial console and power on the device. Interrupt the bootloader by pressing 'st' 2. setenv boot_mode openwrt ; saveenv 3. run boot1 Load firmware via TFTP and write to flash 4. run boot2 Now OpenWrt initramfs should boot 5. upload sysupgrade.bin via scp to /tmp 6. sysupgrade Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: import driver for Adtran SmartRG RGBW LEDDaniel Golle2023-12-10
| | | | | | | Import driver for I2C-connected HolTek MCU controlling the RGBW LED found in Adtran SmartRG devices. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: hack: support inverted LEDs on MaxLinear GPY211 PHYDaniel Golle2023-12-10
| | | | | | | | Add downstream DT property to setup the PHY LEDs of the MaxLinear GPY211 PHY in such way that the VDD of the LED is driven by the SoC pin rather than the GND (which is the default). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: backport upstream mediatek WED changesFelix Fietkau2023-12-08
| | | | | | Reorder and update existing patches Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add SPDX header for Confiabits MT7981 DTSLuis Mita2023-12-06
| | | | | | Fixing ambiguous licensing. Signed-off-by: Luis Mita <luis@luismita.com>
* mediatek: filogic: add Acelink EW-7886CAX supportRafał Miłecki2023-12-05
| | | | | | | | | | | | | | | | | Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point. It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and on-SoC Wi-Fi. There is no printed MAC label (on my unit). My unit came with Mediatek's firmware (based on OpenWrt 21.02) installed. It was possible to simply upgrade using OpenWrt's sysupgrade tool. Another verified upgrade method is using U-Boot (requires UART). During every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade firmware" allows using U-Boot's tftp client to load and flash factory image. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: remove wireless packages for GL-MT2500David Bauer2023-12-03
| | | | | | | This device does not have wireless hardware, thus we don't need to ship neither hostapd nor wireless drivers. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: make GL-MT2500 image work with U-Boot recoveryDavid Bauer2023-12-03
| | | | | | | | | | | | | | | | | | | | | Append metadata in the special GL.iNet format. This also enables use of the web-based U-Boot recovery. U-Boot-Recovery =============== The GL-MT2500 provides web-based U-Boot recovery. For this, hold the reset button pressed for 5 seconds when attaching power to the device. The LED will blink 5 times. Release the reset button. The OpenWrt sysupgrade image can be installed by navigating to http://192.168.1.1 in a web-browser. The device does not work as a DHCP server, so manual IP configuration is required. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: remove kernel build-directives for GL-MT2500David Bauer2023-12-03
| | | | | | | The build-directives for the GL-MT2500 are not required, as the default ones produce working images. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add missing eMMC packages for GL-MT2500David Bauer2023-12-03
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: filogic: Update bootcount init script permissionsChen Minqiang2023-12-02
| | | | | | | | Change permissions of the bootcount init script from old mode 100644 to new mode 100755 to ensure its executability. Fixes: 6cc14bf66aa9 ("filogic: support Telenor branded ZyXEL EX5700") Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* mediatek: add support for Confiabits MT7981Luis Mita2023-11-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981. Specification: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 128 MiB SPI NAND - RAM: 256 MiB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax) - Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN) - USB 2.0 port - Buttons: 1 Reset button, 1 Mesh button. - LEDs: 7x light-blue, 2x warm-white - Serial console: internal 4-pin header, 115200 8n1 - Power: 12 VDC, 1.5 A MAC addresses in stock firmware and in this commit: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 00:0c:43:xx:xx:e1 | label+1 | | LAN | 00:0c:43:xx:xx:e0 | label | | WLAN 2g | 00:0c:43:xx:xx:e0 | label | | WLAN 5g | 02:0c:43:xx:xx:e0 | | +---------+-------------------+-----------+ The label MAC was found in 'Factory', 0x4 Installation: The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image with the 'Keep settings' option turned off. Signed-off-by: Luis Mita <luis@luismita.com>
* kernel: bump 5.15 to 5.15.140John Audia2023-11-29
| | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.140 Removed upstreamed: mvebu/patches-5.15/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.140&id=06d320ca170b4e59bb261e2ce3ffe84e9154d42b Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.64John Audia2023-11-29
| | | | | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.64 Removed upstreamed: ixp4xx/patches-6.1/0001-mtd-cfi_cmdset_0001-Byte-swap-OTP-info.patch[1] mvebu/patches-6.1/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[2] qualcommax/patches-6.1/0026-v6.7-clk-qcom-ipq8074-drop-the-CLK_SET_RATE_PARENT-flag-f.patch[3] Manually rebased: bcm27xx/patches-6.1/950-0111-MMC-added-alternative-MMC-driver.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=3b93096d29c5b9ca2af94be4ee9949c1767acf17 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=b3fd9db79e30d5eb5f76ef1f5b7e4f444af574ea 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=877080a3490102da26b8d969588159b2385f739e Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: add kmod-usb3 to default package set of the ZBT-Z8102AXDaniel Golle2023-11-29
| | | | | | | Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are required to be able to use the USB-connected M.2 slots for 4G/5G modems. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: copy config for Acer Predator W6David Bauer2023-11-27
| | | | | | Config was previously not copied on sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add support for GL.iNet GL-MT2500David Bauer2023-11-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7981BA RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR) MMC: 8GB eMMC (Samsung 8GTF4R) ETH: 1000Base-T LAN (ePHY) 2500Base-T WAN (MaxLinear GPY211C) BTN: 1x Reset Button LED: System (blue/white) VPN (white) USB: 1x USB-A (USB 3.0) UART: 115200 8N1 - Pinout on board next to LAN port Don't connect 3.3V! Known Issues ------------ U-Boot vendor recovery does not seem to accept any images, neither GL.iNet images nor OpenWrt images. Recovery requires serial access! Installation ------------ Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to not retain existing settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* image: use helper function for size unitsTony Ambardar2023-11-26
| | | | | | | | Add the make function 'exp_units' for helping evaluate k/m/g size units in expressions, and use this to consistently replace many ad hoc substitutions like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* mediatek: use mac-baseRosen Penev2023-11-25
| | | | | | mac-address-increment is deprecated. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: convert to nvmem-layoutRosen Penev2023-11-25
| | | | | | Will allow removing mac-address-increment. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts and image recipes to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: remove kmod-usb2 for GL-MT6000Chukun Pan2023-11-25
| | | | | | | The usb driver requires kmod-usb3, not kmod-usb2. Remove the useless kmod-usb2 from default package. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: Cetron CT3003: fixes typo for spi propertiesChukun Pan2023-11-25
| | | | | | | Same as commit 3674689, correct 'buswidth' to 'bus-width'. Also move the nmbm properties outside the partition definition. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AXHauke Mehrtens2023-11-25
| | | | | | | The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX Fixes: c8c2f522625c ("mediatek: add support for Zbtlink ZBT-Z8102AX") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Powered by cgit, Themed by Ted Yin.