aboutsummaryrefslogtreecommitdiff
path: root/target/linux/mediatek
Commit message (Collapse)AuthorAge
...
* mediatek: apply stock configuration for WAN-LEDDavid Bauer2023-05-11
| | | | | | | Apply the same LED configuration used by the vendor-firmware for the GPY211 controlled WAN LED in OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: configure TUF-AX4200 LAN LEDsDavid Bauer2023-05-11
| | | | | | | | | | As we can now configure the switch LED configuration, write the switch LED configuration values from the vendor firmware to the switch-IC. Previously, the switch-LEDs did not show any acitvity or link-status whatsoever. Signed-off-by: David Bauer <mail@david-bauer.net>
* generic: enable CONFIG_ARM_CRYPTO for 32bit arm targetsLu jicong2023-05-10
| | | | | | | Fix following error when building 32bit arm targets with kmod-crypto-sha512 ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing. Signed-off-by: Lu jicong <jiconglu58@gmail.com>
* generic: refresh 5.15 kernel configLu jicong2023-05-10
| | | | | | prepare for enabling CONFIG_ARM_CRYPTO on these targets Signed-off-by: Lu jicong <jiconglu58@gmail.com>
* kernel: improve handling of CONFIG_IO_URINGTony Ambardar2023-05-03
| | | | | | | | | | | | | | | | | | | | | | Kernel setting CONFIG_IO_URING supports high-performance I/O for file access and servers, generally for more performant platforms, and adds ~45 KB to kernel sizes. The need for this on less "beefy" devices is questionable, as is the size cost considering many platforms have kernel size limits which require tricky repartitioning if outgrown. The size cost is also large relative to the ~180 KB bump expected between major OpenWRT kernel releases. No OpenWrt packages have hard dependencies on this; samba4 and mariadb can take advantage if available (+KERNEL_IO_URING:liburing) but otherwise build and work fine. Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting in Config-kernel.in (default Y), remove it from those target configs which unconditionally enable it, and update the defaults to enable it conditionally only on more powerful 64-bit x86 and arm devices. It may still be manually enabled as needed for high-performance custom builds. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel: fix handling of CONFIG_DYNAMIC_DEBUGTony Ambardar2023-05-03
| | | | | | | | | | Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG setting in Config-kernel.in (default N), remove or disable it in target configs which unconditionally enable it, along with the related setting CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* mediatek: no longer hard-code WAN PHY of Netgear WAX206Daniel Golle2023-04-30
| | | | | | | | The RealTek 2.5G PHY providing the WAN port of the Netgear WAX206 has previously been hard-coded in the device tree. Now that the PHY can be probed correctly also via Clause-45 MDIO, use that instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: Deactivate CONFIG_COMPATHauke Mehrtens2023-04-29
| | | | | | | | | | | | | | This deactivates the CONFIG_COMPAT kernel option. With CONFIG_COMPAT the kernel will provide syscall interfaces for arm32 binaries in addition to the interfaces needed for arm64 binaries. In OpenWrt the complete userspace is compiled for this specific architecture and support for 32 bit ARM applications is not needed. This reduces the size and the attack surface for the systems. On all other targets CONFIG_COMPAT is already deactivated. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Activate CONFIG_ARM64_SW_TTBR0_PANHauke Mehrtens2023-04-29
| | | | | | | | | | | | | This activates the CONFIG_ARM64_SW_TTBR0_PAN option for all arm64 kernels by default. The CONFIG_ARM64_SW_TTBR0_PAN option prevents the kernel form accessing user space memory directly. This makes it harder to exploit the kernel. This is activated by default and was already activate on all other arm64 targets before. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Activate CONFIG_HARDENED_USERCOPY for all targetsHauke Mehrtens2023-04-29
| | | | | | | | | | | | | | This activates CONFIG_HARDENED_USERCOPY for the remaining targets. This adds additional checks in the copy_from_user() and copy_to_user() functions. This was not activated for ARCHS38 before because of a bug in the Linux kernel 5.4 till 5.14, which as fixed and is described here: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/15 I do not know why this was deactivated for mt7629 and rockchip. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: remove mt753x driverFelix Fietkau2023-04-29
| | | | | | It is unused Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add support for TP-Link TL-XDR4288/608xChukun Pan2023-04-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128MB RAM: ESMT M15T4G16256A 512MB Ethernet (Max Speed): XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan WiFi: XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R) XDR6086/XDR6088: WiFi1: MT7976GN 2.4GHz 4T4R WiFi2: MT7976AN 5GHz 4T4R Button: Reset, WPS, Turbo USB: 1 x USB 3.0 Power: DC 12V 4A Flash instructions: 1. Execute the following operation to open nc shell: https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting 2. Replace the stock bootloader to OpenWrt's: dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip 3. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 4. Download the initramfs image, and restart the router, waiting for tftp recovery to complete. 5. After openwrt boots up, perform sysupgrade. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> [Add uboot build, fit and sysupgrade support, fix RealTek PHYs] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.15 to 5.15.108John Audia2023-04-22
| | | | | | | | | | | | | | | | | Removed upstreamed: backport-5.15/430-v6.3-ubi-Fix-failure-attaching-when-vid_hdr-offset-equals.patch[1] backport-5.15/612-v6.3-skbuff-Fix-a-race-between-coalescing-and-releasing-S.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=85d7a7044b759d865d10395a357632af00de5867 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=906a6689bb0191ad2a44131a3377006aa098af59 Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: filogic: remove redundant code for tuf-ax4200Chukun Pan2023-04-21
| | | | | | Remove redundant code in 02_network. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: move mac address setting togetherChukun Pan2023-04-21
| | | | | | Simultaneously sort in the order of letters. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: fix network config for mt7986a-rfbChukun Pan2023-04-21
| | | | | | | Fix the network configuration according to the device tree. Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: update kernel config-5.15Daniel Golle2023-04-20
| | | | | | | Expose thermal-zone as hwmon sensor, remove thermal emulation driver and add some missing symbols. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r3: allow up to 3W per SFP moduleDaniel Golle2023-04-20
| | | | | | | | | According to SinoVoip up to 3A @ 3.3V are available for both SFP modules together. Raise energy limit from 1W (default) to 3W, however, be aware that using modules consuming more than 1W will require active cooling! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: backport MEMREAD ioctlMichał Kępień2023-04-18
| | | | | | | | | MEMREAD is a new ioctl for MTD character devices that was first included in Linux 6.1. It allows userspace applications to use the Linux kernel's OOB autoplacement mechanism while reading data from NAND devices. The Yafut tool needs this ioctl to do its job. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* mediatek: sync pinctrl-mt7981 and pinctrl-mt7986 driversDaniel Golle2023-04-13
| | | | | | | Now that new pinconf features have been backported sync pinctrl-mt7981 and pinctrl-m7986 with bleeding-edge upstream versions. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: backport new pinctrl featuresDaniel Golle2023-04-13
| | | | | | | | Backport new features for MediaTek pinctrl/pinconf drivers from upstream. This will serve as the base to improve pinconf bias/pull-up/pull-down on MT7981 and MT7986, and also prepare for upcoming support for MT7988. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: introduce KERNEL_LOADADDR to Device/Default templateDaniel Golle2023-04-05
| | | | | | | | | | | | | | | | | | We need to reset KERNEL_LOADADDR if we use it on a per-device base. Otherwise the previous value will be kept in case a device doesn't define KERNEL_LOADADDR and relies on the default. Move initializing KERNEL_LOADADDR to target/linux/mediatek/image/Makefile, similar to how it's done also on the ramips target. This fixes image size related breakage on devices which rely on the default value of KERNEL_LOADADDR. While at it use 0x48000000 which is more common than the previous default 0x44000000 for the filogic subtarget. Fixed: e7c399bee6 ("filogic: add support for ASUS TUF-AX4200") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: make TUF-AX4200 KERNEL simply expandedDavid Bauer2023-04-04
| | | | | | The KERNEL variable was recursively expanded, breaking other devices. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: re-add wireless driver for TUF-AX4200Andrew Sim2023-03-29
| | | | | | | | | | | The wireless driver package was incorrectly removed from the TUF-AX4200 device-packages, resulting in images without wireless functionality. Fixes: d98c4fb8bfab ("mediatek: broaden filogic target description") Signed-off-by: Andrew Sim <andrewsimz@gmail.com> [rework commit description] Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: fix mtk_eth_soc throughput regressions on gigabit PHY portsFelix Fietkau2023-03-29
| | | | | | Fixes issues on MT7621 and MT7623 switch ports, and PHY ports on all SoC Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: broaden filogic target descriptionDaniel Golle2023-03-27
| | | | | | | The filogic subtarget now also supports MT7981 and will in future also support MT7988. Reflect that in the target description. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add device tree include for the MT7981 SoCDaniel Golle2023-03-27
| | | | | | Add mt7981.dtsi so we can start adding MT7981 devices. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for SPI calibrationDaniel Golle2023-03-27
| | | | | | | Newer MediaTek's SoCs need SPI calibration routines for SPI to work reliably. Import patches for that from MediaTek's SDK. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add PWM support for MT7981 SoCDaniel Golle2023-03-27
| | | | | | | Add patch to support PWM on the MT7981 SoC. This patch will also be submitted to upstream Linux soon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add I2C for MT7981 SoCDaniel Golle2023-03-27
| | | | | | | Add patch to support I2C on the MT7981 SoC. This change will also be submitted to upstream Linux soon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: simplify MaxLinear GPY PHY driverDaniel Golle2023-03-27
| | | | | | | | | | | | | | | The mxl-gpy driver apparently was built in the assumption that SGMII auto-negotiation is always switched on at the MAC. This may be true for few rather recent drivers (why?), but certainly isn't for most drivers unless 'managed = "in-band-status"' is set in device tree. Add patch to the mediatek target which reduces mxl-gpy to behave more like an ordinary PHY driver using out-of-band status. This allows to use these PHYs without rate-adaptation which seems to be at least partially broken/racy in some revisions of the PHY and/or internal PHY firmware. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: mtk_eth_soc: switch to external PCS driverDaniel Golle2023-03-27
| | | | | | Backport patch to make use of the new PCS driver in mtk_eth_soc. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: net: pcs: add driver for MediaTek SGMII PCSDaniel Golle2023-03-27
| | | | | | Backport dedicated PCS driver for MediaTek LynxI SGMII/SerDes unit. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: mtk_eth_soc: allow setting MDIO clock frequencyDaniel Golle2023-03-27
| | | | | | | | Backport patch allowing to set the MDIO bus clock frequency. By default the MDIO bus clock runs on 2.5 MHz, allow increasing it up to 25 MHz. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for built-in GE PHYs of newer SoCsDaniel Golle2023-03-27
| | | | | | | | | | | MT7981 and the upcoming MT7988 have built-in Gigabit Ethernet PHYs. While they share some design properties with the PHYs present in MT753x, they do need calibration data from the SoC's efuse. Add driver to support them. Upstreaming it is planned, but there are still some ongoing discussions with MediaTek. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: backport pinctrl driver for MT7981 SoCDaniel Golle2023-03-27
| | | | | | | Backport the pinctrl driver for the MT7981 SoC. The driver has also been submitted upstream and is part of Linux 6.3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: backport clk driver for MT7981 SoCDaniel Golle2023-03-27
| | | | | | | Backport driver for common clocks in MT7981 SoC. The driver has also been submitted upstream and became part of Linux 6.3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.15 to 5.15.103John Audia2023-03-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased: backport-5.15/704-15-v5.19-net-mtk_eth_soc-move-MAC_MCR-setting-to-mac_finish.patch Removed upstreamed: backport-5.15/060-v6.0-01-tools-build-Add-feature-test-for-init_disassemble_in.patch[1] backport-5.15/060-v6.0-02-tools-include-add-dis-asm-compat.h-to-handle-version.patch[2] backport-5.15/060-v6.0-03-tools-perf-Fix-compilation-error-with-new-binutils.patch[3] backport-5.15/060-v6.0-04-tools-bpf_jit_disasm-Fix-compilation-error-with-new-.patch[4] backport-5.15/060-v6.0-05-tools-bpftool-Fix-compilation-error-with-new-binutil.patch[5] pending-5.15/733-02-net-ethernet-mtk_eth_soc-fix-RX-data-corruption-issu.patch[6] bcm47xx/patches-5.15/170-bgmac-fix-initial-chip-reset-to-support-BCM5358.patch[7] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=51b99dc38c1a053e2e732d7f9e2740e343ae7eae 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=451c9d7b16169645ed291ebb2ca9844caa088f2d 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=97f005c0bdbaf656a7808586d234965385a06c58 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=1c27fab243333821375e4d63128d60093fdbe149 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=4441a90091931fd81607567961dc122f24f735bb 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=2adc29350a5b4669544566f71f208d2abaec60ab 7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=04bfc5bcdfc0fdb73587487c71b04d63807ae15a Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* filogic: add support for ASUS TUF-AX4200David Bauer2023-03-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: MediaTek MT7986 RAM: 512MB DDR3 FLASH: 256MB SPI-NAND (Winbond W25N02KV) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: MediaTek MT7531 Switch MaxLinear GPY211C 2.5 N-Base-T PHY UART: 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.66/24. Rename the image to tufax4200.bin. 2. Connect the TFTP server to the AX4200. Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted. 3. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.66 $ tftpboot 0x46000000 tufax4200.bin $ bootm 0x46000000 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Missing features ---------------- - The LAN port LEDs are driven by the switch but OpenWrt does not correctly configure the output. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: enable bootargs-override for filogic subtargetDavid Bauer2023-03-24
| | | | | | | | | The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs. Without overwriting the cmdline, the kernel crashes when trying to attach the rootfs, as OpenWrt uses a different partition than the vendor OS. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add kernel code for supporting offloading wlan->eth and wlan->wlan ↵Felix Fietkau2023-03-23
| | | | | | | | flows Will be enabled by an upcoming mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: update mtk ppe flow accounting patch to the latest versionFelix Fietkau2023-03-23
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: filogic: move ilm, dlm and cpu_boot in dedicated nodesLorenzo Bianconi2023-03-20
| | | | | | | | This fixes issues with legacy boot loaders that don't process reserved memory regions outside of system RAM Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.15 to 5.15.100John Audia2023-03-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.15/950-0421-Support-RPi-DPI-interface-in-mode6-for-18-bit-color.patch bcm27xx/patches-5.15/950-0706-media-i2c-imx219-Scale-the-pixel-clock-rate-for-the-.patch ramips/patches-5.15/810-uvc-add-iPassion-iP2970-support.patch Removed upstreamed: bcm27xx/patches-5.15/950-0707-drm-vc4-For-DPI-MEDIA_BUS_FMT_RGB565_1X16-is-mode-1-.patch[1] bcm27xx/patches-5.15/950-0596-drm-vc4-dpi-Add-option-for-inverting-pixel-clock-and.patch[2] ipq807x/0006-v5.16-arm64-dts-qcom-Fix-IPQ8074-PCIe-PHY-nodes.patch [3] ipq807x/0034-v6.1-arm64-dts-qcom-ipq8074-fix-PCIe-PHY-serdes-size.patch [4] ipq807x/0103-arm64-dts-qcom-ipq8074-fix-Gen2-PCIe-QMP-PHY.patch [5] ipq807x/0104-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-QMP-PHY.patch [6] ipq807x/0105-arm64-dts-qcom-ipq8074-correct-Gen2-PCIe-ranges.patch [7] ipq807x/0108-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-node.patch [8] ipq807x/0109-arm64-dts-qcom-ipq8074-correct-PCIe-QMP-PHY-output-c.patch [9] ipq807x/0132-arm64-dts-qcom-ipq8074-correct-USB3-QMP-PHY-s-clock-.patch [10] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.99&id=d2991e6b30020e286f2dd9d3b4f43548c547caa6 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/gpu/drm/vc4/vc4_dpi.c?h=v5.15.100&id=8e04aaffb6de5f1ae61de7b671c1531172ccf429 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=a55a645aa303a3f7ec37db69822d5420657626da 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=d9df682bcea57fa25f37bbf17eae56fa05662635 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=7e6eeb5fb3aa9e5feffdb6e137dcc06f5f6410e1 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=e88204931d9a60634cd50bbc679f045439c4b91d 7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=1563af0f28afd3b6d64ac79a2aecced3969c90bf 8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=feb8c71f015d416f1afe90e1f62cf51e47376c67 9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=69c7a270357a7d50ffd3471b14c60250041200e3 10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=dd3d021ae5471d98adf81f1e897431c8657d0a18 Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3 Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me> Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36 Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
* mediatek: add missing DTS entries for WED on MT7986Felix Fietkau2023-03-05
| | | | | | Needed to support WLAN offloading Signed-off-by: Felix Fietkau <nbd@nbd.name>
* linux-firmware: add mt7986 offload firmwareFelix Fietkau2023-03-02
| | | | | | | This is needed for WED support on MT7986. Enable it by default for the filogic subtarget. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* treewide: remove label = "cpu" from DSA dt-bindingArınç ÜNAL2023-02-26
| | | | | | | This is not used by the DSA dt-binding, so remove it from all devicetrees. Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* mediatek: add support for Netgear WAX206Marcel Ziswiler2023-02-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7622BV * RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK) * Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ) * Wi-Fi 2.4/5 GHz 4T4R: * 2.4 GHz: MediaTek MT7622BV * 5 GHz: MediaTek MT7915AN/MT7975AN * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY) * Switch: MediaTek MT7531AE * LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4, Wifin and Wifia dual-colour LEDs + Reset pin) * UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v, 115200n8 * Power: 12 VDC, 2.5 A Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * U-Boot allows booting an initramfs image via TFTP as follows: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.100 tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb bootm Known Limitations: * The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the moment. If connected to a multi-gig port the speed has to be manually set to 1G/full either for the switch port or in OpenWrt. For example add the following to /etc/rc.local to set it on boot: /usr/sbin/ethtool -s wan speed 1000 duplex full Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to WAX206 GPL source: https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar * openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts DTS file for this device. * openwrt/target/linux/mediatek/image/mt7622.mk Image creation code for this device Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [fix WAN port (1G only), adjust partition layout, adjust image creation] Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
* mediatek: mtk_thermal: replace with upstream patchDaniel Golle2023-02-15
| | | | | | | Replace local patch adding thermal support for MT7986 with version accepted upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: fix rootfs/ubi detection for Xiaomi AX6SOleg S2023-02-11
| | | | | | | | | | | | | | | | | By specifying the flag "denx,fit" for partition "kernel", the kernel try to find rootfs in the same partition during boot. Reality is that the placement of rootfs is precisely determined by the name of another partition -"ubi". It was also found that on some device (for example devices with NAND chips), the "Denx search engine" manages to find roots at the end of partition "kernel", but such partition doesn't exist and is empty there. Fix this by removing the "denx,fit" flag from partition "kernel". With this change the original behavior of searchif rootfs in partition "ubi" is restored. Signed-off-by: Oleg S <remittor@gmail.com>
Powered by cgit, Themed by Ted Yin.