aboutsummaryrefslogtreecommitdiff
path: root/target/linux/mediatek
Commit message (Collapse)AuthorAge
...
* mediatek: filogic: remove stray quoteDaniel Golle2023-08-28
| | | | | | | | When adapting the network configuration for MT7988 RFB a stray quote was left in a script. Remove it to fix generating the default network configuration. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* generic: sync MediaTek Ethernet driver with upstreamDaniel Golle2023-08-28
| | | | | | | Import commits from upstream Linux replacing some downstream patches. Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Ubiquiti UniFi 6 LR v3Daniel Golle2023-08-28
| | | | | | | | | Some recent models of the Ubiquiti Networks UniFi 6 LR access point come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add build for this variant so we can support Ethernet with the PHY. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: generate bootloader artifacts for mt7988_rfbDaniel Golle2023-08-28
| | | | | | | Switch to OpenWrt uImage.FIT bootmethod and include various bootloader artifacts with the generated binaries. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: improve mt7981.dtsiDaniel Golle2023-08-28
| | | | | | | * re-factor WED components to boot fine also on limited loaders * add LEDs of integrated GE PHY Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: improve pinctrl driversDaniel Golle2023-08-28
| | | | | | | Set correct pull-type data and add additional uart groups for MT7981. Assign functions to configure pin bias for MT7986. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: i2c: mt65xx: allow optional pmic clockDaniel Golle2023-08-28
| | | | | | | | | | | | | Using the I2C host controller on the MT7981 SoC requires 4 clocks to be enabled. One of them, the pmic clk, is only enabled in case 'mediatek,have-pmic' is also set which has other consequences which are not desired in this case. Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty is not present and the bus is not used to connect to a pmic, but may still require to enable the pmic clock. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: re-add dropped properties on BPi-R3Daniel Golle2023-08-28
| | | | | | | | | | | Unfortunately some device tree properties have slipped under the table when switching from our downstream device tree. Bring back 3W power for SFP cages and restore thermal trip points to make sense again. Fixes: 7a0ec001ff ("mediatek: sync MT7986 device trees with upstream") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 6.1 to 6.1.47John Audia2023-08-26
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.47 All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: enable NMBM remapping for NWA50AX Pro UBIDavid Bauer2023-08-25
| | | | | | | | | Don't skip remapping of the UBI area for the ZyXEL NWA50AX Pro. This is due to the kernel being loaded from the UBI partition by U-Boot. Link: https://github.com/openwrt/openwrt/pull/13335 Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: enable NWA50AX Pro eth LEDsDavid Bauer2023-08-22
| | | | | | | | | | | | | Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as well as activity. Both LED's are configured pulsing. AMBER | 10/100 GREEN | 1000 A+G | 2500 Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: filogic: wax220: cleanup device treeStefan Agner2023-08-22
| | | | | | | Fix compatible string to match what is supported upstream, fix alignment and order MTD partitions according to offset. Signed-off-by: Stefan Agner <stefan@agner.ch>
* mediatek: filogic: wax220: support factory imageStefan Agner2023-08-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable building a factory image which can be flashed through the OEM firmware's web interface. It seems that the web interface requires a minimum file size of 10MiB, otherwise it will not accept the image. The update image is a regular sysupgrade tarball packed in a Netgear encrypted image. The Netgear encrypted image is the same as used in WAX202 or WAX206, including the encryption keys and IV. This adds a script which creates the rootfs_data volume on first startup. This is required since the OEM firmware's sysupgrade scripts do not create such a paritition. Note that any script ordered after 70_initramfs_test will not get executed on initramfs. Hence this new script 75_rootfs_prepare won't create the rootfs_data volume when using the recovery initramfs. Also, this deletes the kernel_backup and rootfs_backup volumes in case we have to create the rootfs_data volumes. This makes sure that OpenWrt is the actual backup firmware instead of the stock firmware. References in WAX220 GPL source: https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz * package/base-files/files/lib/upgrade/nand.sh:186 Creation of rootfs_data is disabled * Uboot-upstream/board/mediatek/common/ubi_helper.c Automatic creation of UBI backup volumes Signed-off-by: Stefan Agner <stefan@agner.ch>
* mediatek: add missing packages for Acer Predator W6David Bauer2023-08-22
| | | | | | Add missing packages for creating the overlay filesystem. Signed-off-by: David Bauer <mail@david-bauer.net>
* filogic: support Telenor branded ZyXEL EX5700Bjørn Mork2023-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Telenor quirks -------------- The operator specific firmware running on the Telenor branded ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt installation. Notable changes to U-Boot include - environment is stored in RAM and reset to defaults when power cycled - dual partition scheme with "nomimal" or "rescue" systems, falling back to "rescue" unless the OS signals success in 3 attempts - several runtime additions to the device-tree Some of these modifications have side effects requiring workarounds - U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash unless this node exists - U-Boot verifies that the selected rootfs UBI volume exists, and refuses to boot if it doesn't. The chosen "rootfs" volume must contain a squashfs signature even for tftp or initramfs booting. - U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr" variable to the label mac. But "factoryparams" does not always exist. Instead there is a "RIP" volume containing all the factory data. Copying the "RIP" volume to "factoryparams" will fix this Hardware -------- SOC: MediaTek MT7986 RAM: 1GB DDR4 FLASH: 512MB SPI-NAND (Mikron xxx) WIFI: Mediatek MT7986 802.11ax 5 GHz Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz ETH: MediaTek MT7531 Switch + SoC 3 x builtin 1G phy (lan1, lan2, lan3) 2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan) USB: 1 x USB 3.2 Enhanced SuperSpeed port UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.2/24. Rename the image to C0A80101.img. 2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial console, Interrupt the autoboot process by pressing ESC when prompted. 3. Download and boot the OpenWrt initramfs image. $ env set uboot_bootcount 0 $ env set firmware nominal $ tftpboot $ bootm 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Missing features ---------------- - The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but OpenWrt does not correctly configure the output. - The "lan4" and "wan" port LEDs are driven by the GPH211C phys and not configured by OpenWrt. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: filogic: set wan label in preinitBjørn Mork2023-08-20
| | | | | | | | | Implement the functionality of target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch in userspace, since the driver patch has been rejected as a generic solution: https://github.com/openwrt/openwrt/pull/11435 Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: filogic: mt7988: mark RTC clock as criticalDaniel Golle2023-08-13
| | | | | | | | A dependency of the MT7988 MMC host controller on the SoC's RTC clock being running has been discovered. Mark RTC clock as critical to fix MMC host on MT7988. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.15 to 5.15.126John Audia2023-08-13
| | | | | | | | | | | | | | | 1. Disable unneeded errata Kconfig symbols 2. Update kernel Changelog: https://lore.kernel.org/stable/2023081111-unlocking-synopsis-d7d5@gregkh/ All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.44John Audia2023-08-09
| | | | | | | | | | | | Changelog: https://lore.kernel.org/stable/2023080822-repost-unfiled-2f01@gregkh/ All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.43John Audia2023-08-09
| | | | | | | | | | | | | | | | | | | | | 1. Disable Ampere errata fix in target/linux/generic/config-6.1 2. Update kernel Changelog: https://lore.kernel.org/stable/2023061431-modular-data-8489@gregkh/ Manually rebased: bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch bcm27xx/patches-6.1/950-0520-xhci-constrain-XHCI_VLI_HUB_TT_QUIRK-to-old-firmware.patch All other patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.125John Audia2023-08-09
| | | | | | | | | | 1. Add new symbols to generic config 2. Bump kernel Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/ All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.124John Audia2023-08-09
| | | | | | | | | | | | | Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/ 1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk due to upstream moving vxlan to its own directory[1]. @john-tho suggested using the the 6.1 xvlan FILES to circumvent. 2. All patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103 Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: add support for Acer Predator W6David Bauer2023-08-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: MediaTek MT7986A RAM: 1GB DDR4 FLASH: 4GB eMMC WiFi: 2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC 4x4 5 GHz 802.11 a/n/ac/ax MT7986 2x2 6 GHz 802.11ax MT7916 DBDC ETH: 4x LAN 1Gbit/s (MT7531) 1x WAN 2.5Gbit/s (GPY211) BTN: RESET, WPS LED: Antenna LEDs (GPIO) Mood-LED (Kinetic KTD2601) - unsupported UART: Header nest to USB port - 3V3 115200 8N1 [BUTTON] GND - RX - TX [USB] Installation ------------ 1. Connect to the device using serial console. 2. Interrupt the Autoboot process when promted by sending '0' twice. 3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name the image "predator.bin" and conenct the TFTP server to the routers LAN port. 4. Configure U-Boot to allow loading unsigned images from MMC $ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000'; saveenv 5. Transfer the image from U-Boot $ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 6. Wait for OpenWrt to boot 7. Transfer the OpenWrt sysupgrade image to the router using scp. 8. Install OpenWrt using sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: filogic: restore non-const type in pinctrl-mt7988 driverDaniel Golle2023-08-03
| | | | | | | | When building with Linux 5.15 the 'const' type results in warnings. Restore the original non-const type in those cases. Fixes: 36d0aa9c2d ("mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: update MT7988 device treeDaniel Golle2023-08-03
| | | | | | | | * move ethernet to mt7988a.dtsi * move switch definition to mt7988a.dtsi * add PHY LEDs Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDKDaniel Golle2023-08-03
| | | | | | Update pinctrl driver for the MT7988 with driver from mtk-openwrt-feeds. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: enable driver for MediaTek XS-PHYDaniel Golle2023-07-31
| | | | | | | Enable driver for MediaTek SuperSpeedPlus XS-PHY transceiver for the USB3.1 GEN2 controllers found in the MT7988 SoC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.15 to 5.15.123John Audia2023-07-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased: bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*] Removed upstreamed: backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1] backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2] pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3] pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4] bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5] bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499 Build system: x86/64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Audia <therealgraysky@proton.me> [rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: filogic: fix broken sysupgrade scriptPetr Štetiar2023-07-28
| | | | | | | | | Changes introduced in commit 54dc1cde48a4 ("mediatek: filogic: add support for Xiaomi WR30U") missed to end the case item with mandatory `;;` which lead to a broken sysupgrade. Fixes: 54dc1cde48a4 ("mediatek: filogic: add support for Xiaomi WR30U") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mediatek: filogic: add specific layout for WR30UHank Moretti2023-07-27
| | | | | | | | | Because this device enable NMBM by default, most users use custom U-Boot with NMBM-Enabled in Chinese forums. This layout is the same as the ubootmod layout but enabling NMBM. Signed-off-by: Hank Moretti <mchank9999@gmail.com>
* mediatek: filogic: add support for Xiaomi WR30UHank Moretti2023-07-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: ESMT F50L1G41LB 128MB RAM: NT52B128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A Flash instructions: 1. Get ssh access Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22 2. Backup import partitions ``` dev: size erasesize name mtd1: 00100000 00020000 "BL2" mtd2: 00040000 00020000 "Nvram" mtd3: 00040000 00020000 "Bdata" mtd4: 00200000 00020000 "Factory" mtd5: 00200000 00020000 "FIP" mtd8: 02200000 00020000 "ubi" mtd9: 02200000 00020000 "ubi1" mtd12: 00040000 00020000 "KF" ``` Use these commands blow to backup your stock partitions. ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then, transfer them to your computer via scp, netcat, tftp or others and keep them in a safe place. 3. Setup Nvram Get the current stock: `cat /proc/cmdline` If you find `firmware=0` or `mtd=ubi`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` If you find `firmware=1` or `mtd=ubi1`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` 4. Flash stock-initramfs-factory.ubi If you find `firmware=0` or `mtd=ubi`: `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi` If you find `firmware=1` or `mtd=ubi1`: `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 5. Setup uboot-env Now it will be setup automatically in upgrade process, you can skip this step. If your `fw_setenv` did not work, you need run this command: `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config` Then setup uboot-env: ``` fw_setenv boot_wait on fw_setenv uart_en 1 fw_setenv flag_boot_rootfs 0 fw_setenv flag_last_success 1 fw_setenv flag_boot_success 1 fw_setenv flag_try_sys1_failed 8 fw_setenv flag_try_sys2_failed 8 fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata), 2048k(factory),2048k(fip),256k(crash),256k(crash_log), 34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)" ``` 6. Flash stock-squashfs-sysupgrade.bin Use shell command: `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin` Or go to luci web. If you need to change to Openwrt U-Boot layout, do next. If you do not need, please ignore it. Change to OpenWrt U-Boot: 1. Flash ubootmod-initramfs-factory.ubi Check mtd partitions: `cat /proc/mtd` ``` mtd7: 00040000 00020000 "KF" mtd8: 02200000 00020000 "ubi_kernel" mtd9: 04e00000 00020000 "ubi" ``` Run following command: `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 2. Check mtd again ``` mtd7: 00040000 00020000 "KF" mtd8: 07000000 00020000 "ubi" ``` Make sure mtd8 is ubi. 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Clean up pstore Run Command: `rm -f /sys/fs/pstore/*` 5. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 6. (Optional) Add recovery boot feature. ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb ``` 7. Flash Openwrt U-Boot ``` mtd write /tmp/ubootmod-preloader.bin BL2 mtd write /tmp/ubootmod-bl31-uboot.fip FIP ``` 6. Flash ubootmod-squashfs-sysupgrade.itb Use shell command: `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb` Or go to luci web. Now everything is done, Enjoy! Go Back to stock from Openwrt U-Boot: 1. Force flash ubootmod-initramfs-recovery.itb Use shell command: `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb` Or go to luci web. Then it should boot to the openwrt initramfs system now. 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock U-Boot and ubi ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. Go Back to stock from stock layout Openwrt: Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Notes: 1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM. Please make your backup safe. Signed-off-by: Hank Moretti <mchank9999@gmail.com>
* kernel: bump 6.1 to 6.1.40John Audia2023-07-25
| | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-6.1/701-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1] generic/pending-6.1/160-workqueue-fix-enum-type-for-gcc-13.patch[2] qualcommax/patches-6.1/0022-v6.5-soc-qcom-mdt_loader-Fix-unconditional-call-to-scm_pa.patch[3] Manually rebased: bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch bcm53xx/patches-6.1/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=685b57a1221c38ec8b456f968264d2496715820c 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=2d57a1590f4d8c516f5aaf8fd5bb4f52d67275d8 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=33f8dff6e1cbba5c2ec85fa5649c0a759a7e685c Build system: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod Build-tested: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.39John Audia2023-07-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-6.1/803-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[1] generic/pending-6.1/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[2] bcm27xx/patches-6.1/950-0034-drm-bridge-Introduce-pre_enable_upstream_first-to-al.patch[3] bcm27xx/patches-6.1/950-0439-nvmem-Use-NVMEM_DEVID_AUTO.patch[4] bcm4908/patches-6.1/040-mtd-parsers-refer-to-ARCH_BCMBCA-instead-of-ARCH_BCM.patch[5] bcm53xx/patches-6.1/031-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[6] bcm53xx/patches-6.1/031-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[7] mediatek/patches-6.1/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch[8] qualcommax/patches-6.1/0008-v6.2-clk-qcom-reset-support-resetting-multiple-bits.patch[9] Manually rebased: bcm27xx/patches-6.1/950-0035-drm-panel-Add-prepare_upstream_first-flag-to-drm_pan.patch bcm27xx/patches-6.1/950-0404-drm-panel-panel-ilitek9881c-Add-prepare_upstream_fir.patch bcm27xx/patches-6.1/950-0699-Bluetooth-hci_sync-Add-fallback-bd-address-prop.patch mediatek/patches-6.1/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ab0bd172d6289310a05a0cd15e1432e828d386ae 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=6df680709d901346831ef8f221cc90a42062c526 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=5044e5f2511c9afdf9880d2bb6b9d37dfc345dac 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=e27948f329f7e02591ed1feb9a7710c2ccf89a83 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ad2928e7f3f6120a0bd18aa1056b3b24068027c5 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=2b55a985727833f37c39911f34096b3fdf2a367d 7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=90d4c487cd658b51212eb65ae804ab11af193672 8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=7e3ee25e8c7c7be1eacdfc6d9f5f0e550a2af241 9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=b20854ef6c4955be3310975a72f02d92cb01d6d4 Build system: x86/64 Build-tested: x86/64 Run-tested: x86/64 Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de> Co-authored-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: John Audia <therealgraysky@proton.me> [ rebase bcm27xx and mediatek patches, refresh commit description ] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> [ minor fixup to bcm27xx patches, refresh commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mediatek: add missing SPDX headerDavid Bauer2023-07-22
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: filogic: set DEVICE_DTS_LOADADDR for BPi-R3Daniel Golle2023-07-22
| | | | | | | U-Boot complains that the overlayed DT needs relocation, so set DEVICE_DTS_LOADADDR to have it relocated. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for ZyXEL NWA50AX ProDavid Bauer2023-07-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7981 RAM: 512M DDR4 FLASH: 256M NAND ETH: MaxLinear GPY211 (2.5GbE N Base-T) WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax) BTN: 1x Reset LED: 1x Multi-Color UART Console ------------ Available below the rubber cover next to the ethernet port. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. In case this is not the case, OpenWrt will boot only one time, returning to the ZyXEL firmware the second boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP / Recovery ---------------------------- This installation routine is especially useful in case of a bricked device. Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin. $ atnf nwa50axpro-openwrt-initramfs.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd9 get-status $ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd9 set-active-image 0 Copy the OpenWrt sysupgrade image to the device using scp. Write the sysupgrade image to NAND using sysupgrade. $ sysupgrade -n image.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: replace hack for MaxLinear 2.5G PHYDaniel Golle2023-07-08
| | | | | | Replace hack with proper patch also for Linux 5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: dts: mt7988a: remove boottrap hackDaniel Golle2023-07-08
| | | | | | | The PHY driver now uses regmap created from pio syscon, we no longer need the boottrap device. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: use backported Ethernet PHY driver also for 5.15Daniel Golle2023-07-08
| | | | | | | Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the driver in files-5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: dts: mt7988a: wire-up mediatek,pio for PHY LEDsDaniel Golle2023-07-08
| | | | | | | | | | The PHY driver needs to read a register containing the values of the bootstrap pins (which happen to be the PHY LEDs) to determine the LED polarities. Allow regmap access to first pinctrl bank by adding the 'syscon' compatible, and reference the pinctrl in the MDIO bus where the PHY driver will look for it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: remove CRYPTO_BLAKE2S from all >=5.15Christian Svensson2023-07-08
| | | | | | | | | This option was removed from upstream kernel back in 2022. See commits: 2d16803c562ecc644803d42ba98a8e0aef9c014e (>=6.0) 3dd33a09f5dc12ccb0902923c4c784eb0f8c7554 (>=5.15.61 backport) Signed-off-by: Christian Svensson <blue@cmd.nu>
* kernel: bump 5.15 to 5.15.120John Audia2023-07-07
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: expose testing Linux 6.1 testing kernelDaniel Golle2023-07-07
| | | | | | | Set KERNEL_TESTING_PATCHVER:=6.1 to allow building all subtargets with Linux 6.1. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: adapt kernel configuration for Linux 6.1Daniel Golle2023-07-07
| | | | | | Update kernel configuration to build Linux 6.1 for all subtargets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: copy config-5.15 to config-6.1 for all subtargetsDaniel Golle2023-07-07
| | | | | | | To ease review, first copy all subtargets' kernel config-5.15 to the to-be-adapted config-6.1. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: adapt files and patches for Linux 6.1Daniel Golle2023-07-07
| | | | | | | | | With Linux 6.1 many of our downstream patches and out-of-tree files can be removed or at least replaced by backported upstream commits. Signed-off-by: Daniel Golle <daniel@makrotopia.org> [fix CMDLINE_OVERRIDE for arm64] Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: copy patches and files for Linux 6.1Daniel Golle2023-07-07
| | | | | | | First step only copies patches-5.15 and files-5.15 to patches-6.1 and files-6.1 respectively. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: prepare old rtk switch driver for use with Linux 6.1Daniel Golle2023-07-07
| | | | | | | | | | The old RealTek RTL8367S switch driver which is used for some MT7622 devices needs to be modified to no longer free the GPIO after reset has completed. This is due to Linux 5.19 removing devm_gpio_free via commit 2b038e786f83 ("gpiolib: devres: Get rid of unused devm_gpio_free()") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: define NMBM management region for WAX220David Bauer2023-07-02
| | | | | | | | The NETGEAR WAX220 employs NMBM on SPI-NAND. In order to avoid dealing with invalid factory data, enable NMBM in the area preceding the UBI volume. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: filogic: add H3C Magic NX30 Pro supportChukun Pan2023-07-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: W25N01GVZEIG 128MB RAM: NT5CB128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. PC run command: "telnet 192.168.124.1 99" Username: H3C, password is the web login password of the router. 2. Download preloader.bin and bl31-uboot.fip 3. PC run command: "python3 -m http.server 80" 4. Download files in the telnet window: "wget http://192.168.124.xx/xxx.bin" Replace xx with your PC's IP and the preloader.bin and bl31-uboot.fip. 5. Flushing openwrt's uboot: "mtd write xxx-preloader.bin BL2" "mtd write xxx-bl31-uboot.fip FIP" 6. Connect to the router via the Lan port, set a static ip of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Download initramfs image, reboot router, waiting for tftp recovery to complete. 8. After openwrt boots up, perform sysupgrade. Note: 1. The u-boot-env partition on mtd is empty, OEM stores their env on ubi:u-boot-env. 2. Back up all mtd partitions before flashing. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Powered by cgit, Themed by Ted Yin.