aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ipq40xx/image/generic.mk
Commit message (Collapse)AuthorAge
...
* ipq40xx: Convert plasmacloud,pa1200 to DSASven Eckelmann2022-11-13
| | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a62 to DSASven Eckelmann2022-11-12
| | | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a42 to DSASven Eckelmann2022-11-12
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: D-Link DAP-2610: convert to DSAGuillaume Lefebvre2022-11-12
| | | | | | | Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: convert to DSA and enable Netgear Orbi devicesDavide Fioravanti2022-10-25
| | | | | | | | | | Convert to DSA and enable again Netgear Orbi devices: - RBR50 - RBS50 - SRR60 - SRS60 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ipq40xx: convert to DSA and enable mobipromo,cm520-79fJack Chen2022-10-23
| | | | | | | Convert to DSA and enable the MobiPromo CM520-79F device again. Signed-off-by: Jack Chen <redchenjs@live.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: convert to DSA and enable asus,rt-ac42uChen Minqiang2022-10-22
| | | | | | | This convert board asus,rt-ac42u to DSA and re-enable it Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq40xx: convert to DSA and enable Sony NCP-HG100/CellularINAGAKI Hiroshi2022-10-09
| | | | | | | This patch converts networking on Sony NCP-HG100/Cellular to DSA and re-enables support for the device. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq40xx: ZTE MF289F: convert to DSADirk Buchwalder2022-10-09
| | | | | | | | | Convert ZTE MF289F device to DSA, re-order network ports to match the labels on the case and re-enable the device. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: pakedge_wr-1: convert to DSATomasz Maciej Nowak2022-10-05
| | | | | | | | | Convert pakedge_wr-1 device to DSA and enable it. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>i [ improve commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: luma_wrtq-329acn: convert to DSATomasz Maciej Nowak2022-10-05
| | | | | | | | | Convert luma_wrtq-329acn device to DSA and enable it. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> [ improve commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: disable boards not converted to DSADavid Bauer2022-10-02
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: Add ZTE MF289FGiammarco Marzano2022-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Sony NCP-HG100/CellularINAGAKI Hiroshi2022-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac (WiFi-5) wireless function, based on IPQ4019. Specification: - SoC : Qualcomm IPQ4019 - RAM : DDR3 512 MiB (H5TC4G63EFR) - Flash : eMMC 4 GiB (THGBMNG5D1LBAIT) - WLAN : 2.4/5 GHz 2T2R (IPQ4019) - Ethernet : 10/100/1000 Mbps x2 - Transceiver : Qualcomm QCA8072 - WWAN : Telit LN940A9 - Z-Wave : Silicon Labs ZM5101 - Bluetooth : Qualcomm CSR8811 - Audio DAC : Realtek ALC5629 - Audio Amp. : Realtek ALC1304 - Voice Input Processor : Conexant CX20924 - Micro Controller Unit : Nuvoton MINI54FDE - RGB LED, Fan, Temp. sensors - Touch Sensor : Cypress CY8C4014LQI - RGB LED driver : TI LP55231 (2x) - LEDs/Keys : 11x, 6x - UART : through-hole on PCB - J1: 3.3V, TX, RX, GND from tri-angle marking - 115200n8 - Power : 12 VDC, 2.5 A Flash instruction using initramfs image: 1. Prepare TFTP server with the IP address 192.168.132.100 and place the initramfs image to TFTP directory with the name "C0A88401.img" 2. Boot NCP-HG100/Cellular and interrupt after the message "Hit any key to stop autoboot: 2" 3. Perform the following commands and set bootcmd to allow booting from eMMC setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000" saveenv 4. Perform the following command to load/boot the OpenWrt initramfs image tftpboot && bootm 5. On the initramfs image, perform sysupgrade with the sysupgrade image (if needed, backup eMMC partitions by dd command and download to other place before performing sysupgrade) 6. Wait for ~120 seconds to complete flashing Known issues: - There are no drivers for audio-related chips/functions in Linux Kernel and OpenWrt, they cannot be used. - There is no driver for MINI54FDE Micro-Controller Unit, customized for this device by the firmware in the MCU. This chip controls the following functions, but they cannot be controlled in OpenWrt. - RGB LED - Fan this fan is controlled automatically by MCU by default, without driver - Thermal Sensors (2x) - Currently, there is no driver or tool for CY8C4014LQI and cannot be controlled. It cannot be exited from "booting mode" and moved to "normal op mode" after booting. And also, the 4x buttons (mic mute, vol down, vol up, alexa trigger) connected to the IC cannot be controlled. - it can be exited from "booting mode" by installing and executing i2cset command: opkg update opkg install i2c-tools i2cset -y 1 0x14 0xf 1 - There is a connection issue on the control by uqmi for the WWAN module. But modemmanager can be used without any issues and the use of it is recommended. - With the F2FS format, too many errors are reported on erasing eMMC partition "rootfs_data" while booting: [ 1.360270] sdhci: Secure Digital Host Controller Interface driver [ 1.363636] sdhci: Copyright(c) Pierre Ossman [ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO ... [ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 1.528325] mmc0: new HS200 MMC card at address 0001 [ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB [ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB [ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB [ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0) [ 1.550323] Alternate GPT is invalid, using primary GPT. [ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 ... [ 8.841400] mount_root: loading kmods from internal overlay [ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 9.240465] block: attempting to load /etc/config/fstab [ 9.246722] block: unable to load configuration (fstab: Entry not found) [ 9.246863] block: no usable configuration [ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet [ 9.438915] urandom_read: 5 callbacks suppressed [ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read) [ 12.243332] mmc_erase: erase error -110, status 0x800 [ 12.246638] mmc0: cache flush error -110 [ 15.134585] mmc_erase: erase error -110, status 0x800 [ 15.135891] mmc_erase: group start error -110, status 0x0 [ 15.139850] mmc_erase: group start error -110, status 0x0 ...(too many the same errors)... [ 17.350811] mmc_erase: group start error -110, status 0x0 [ 17.356197] mmc_erase: group start error -110, status 0x0 [ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00 [ 17.446910] mmc0: tuning execution failed: -5 [ 17.447111] mmc0: cache flush error -110 [ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint [ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b [ 18.198691] block: attempting to load /etc/config/fstab [ 18.198972] block: unable to load configuration (fstab: Entry not found) [ 18.203029] block: no usable configuration [ 18.211371] mount_root: overlay filesystem has not been fully initialized yet [ 18.214487] mount_root: switching to f2fs overlay So, this support uses ext4 format instead which has no errors. Note: - The primary uart is shared for debug console and Z-Wave chip. The function is switched by GPIO15 (Linux: 427). value: 1: debug console 0: Z-Wave - NCP-HG100/Cellular has 2x os-image pairs in eMMC. - 0:HLOS, rootfs - 0:HLOS_1, rootfs_1 In OpenWrt, the first image pair is used. - "bootipq" command in U-Boot requires authentication with signed-image by default. To boot unsigned image of OpenWrt, use "mmc read" and "bootm" command instead. - This support is for "Cellular" variant of NCP-HG100 and not tested on "WLAN" (non-cellular) variant. - The board files of ipq-wifi may also be used in "WLAN" variant of NCP-HG100, but unconfirmed and add files as for "Cellular" variant. - "NET" LED is used to indicate WWAN status in stock firmware. - There is no MAC address information in the label on the case, use the address included in UUID in the label as "label-MAC" instead. - The "CLOUD" LEDs are partially used for indication of system status in stock firmware, use they as status LEDs in OpenWrt instead of RGB LED connected to the MCU. MAC addresses: LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex)) WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex)) 2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex)) 5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex)) partition layout in eMMC (by fdisk, GPT): Disk /dev/mmcblk0: 7733248 sectors, 3776M Logical sector size: 512 Disk identifier (GUID): **** Partition table holds up to 20 entries First usable sector is 34, last usable sector is 7634910 Number Start (sector) End (sector) Size Name 1 34 1057 512K 0:SBL1 2 1058 2081 512K 0:BOOTCONFIG 3 2082 3105 512K 0:QSEE 4 3106 4129 512K 0:QSEE_1 5 4130 4641 256K 0:CDT 6 4642 5153 256K 0:CDT_1 7 5154 6177 512K 0:BOOTCONFIG1 8 6178 6689 256K 0:APPSBLENV 9 6690 8737 1024K 0:APPSBL 10 8738 10785 1024K 0:APPSBL_1 11 10786 11297 256K 0:ART 12 11298 11809 256K 0:HSEE 13 11810 28193 8192K 0:HLOS 14 28194 44577 8192K 0:HLOS_1 15 44578 306721 128M rootfs 16 306722 568865 128M rootfs_1 17 568866 3958065 1654M rootfs_data [initial work] Signed-off-by: Iwao Yuki <dev.clef@gmail.com> Co-developed-by: Iwao Yuki <dev.clef@gmail.com> [adjustments, cleanups, commit message, sending patch] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (dropped clk_unused_ignore, dropped 901-* patches, renamed key nodes, changed LEDs chan/labels to match func-en, made :net -> (w)wan leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: disable devices with 3MiB kernel sizeSungbo Eo2022-09-18
| | | | | | | | | The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently fail on buildbots due to the KERNEL_SIZE, as stated in commit 17b7756b5a20 ("ipq40xx: 5.15: add testing kernel version"). Disable these boards for now. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: cellc_rtl30vw: fix imagebuilder generationGregory Detal2022-09-11
| | | | | | | | | | | | | | | | | The image build process was modifying the generated IMAGE_KERNEL to append rootfs information (crc). This caused: - sysupgrade & factory images to contain 2 times the root.squashfs information due to both modifying the same IMAGE_KERNEL. - the generated imagebuilder to contain an erroneous IMAGE_KERNEL that contained references to an unexisting root.squashfs (the one from previous cause). The RTL30VW wasn't therefore able to boot the generated images as they contained checksums from non existing rootfs. This commit makes sure to use a temporary IMAGE_KERNEL to append the rootfs information for both factory and sysupgrade images. Fixes: #10511 Signed-off-by: Gregory Detal <gregory.detal@tessares.net>
* ipq40xx: add LTE packages for GL-AP1300David Bauer2022-09-09
| | | | | | | Add LTE packages required for operating the LTE modem optionally shipped with the GL-AP1300. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: add Pakedge WR-1 supportTomasz Maciej Nowak2022-09-07
| | | | | | | | | | Calibration variants: Pakedge-WR-1 ETSI, FCC and IC-2.4GHz Pakedge-WR-1-ACMA ACMA Pakedge-WR-1-IC IC-5GHz Pakedge-WR-1-SRRC SRRC Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add support for Pakedge WR-1Tomasz Maciej Nowak2022-09-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pakedge WR-1 is a dual-band wireless router. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 32 MB SPI NOR WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 5x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 LEDS: 8x (3 GPIO controlled, 5 connected to switch) Buttons: 1x GPIO controlled UART: pin header J5 1. 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Rename initramfs image to: openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb and copy it to USB flash drive with FAT32 file system. 2. Connect USB flash drive to the router and apply power while pressing reset button. Hold the button, on the lates bootloader version, when Power and WiFi-5 LEDs will start blinking release it. For the older bootloader holding it for 15 seconds should suffice. 3. Now the router boots the initramfs image, at some point (close to one minute) the Power LED will start blinking, when stops, router is fully booted. 4. Connect to one of LAN ports and use SSH to open the shell at 192.168.1.1. 5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if, at some point, You want to go back to original firmware. The firmware provided by manufacturer on its site is encrypted and U-Boot accepts only decrypted factory images, so there's no way to restore original firmware. 6. If the backup is prepared, transfer the sysupgrade image to the router and use 'sysupgrade' command to flash it. 7. After successful flashing router will reboot. At some point the Power LED will start blinking, wait till it stops, then router is ready for configuration. Additional information U-Boot command line is password protected. Password is unknown. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add support for Extreme Networks WS-AP3915iDavid Bauer2022-09-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- Qualcomm IPQ4029 WiSoC 2T2R 802.11 abgn 2T2R 802.11 nac Macronix MX25L25635E SPI-NOR (32M) 512M DDR3 RAM 1x Gigabit LAN 1x Cisco RJ-45 Console port Settings: 115200 8N1 Installation ------------ 1. Attach to the Console port. Power up the device and press the s key to interrupt autoboot. 2. The default username / password to the bootloader is admin / new2day 3. Update the bootcommand to allow loading OpenWrt. $ setenv ramboot_openwrt "setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x86000000 openwrt-3915.bin; bootm" $ setenv boot_openwrt "sf probe; sf read 0x88000000 0x280000 0xc00000; bootm 0x88000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Download the OpenWrt initramfs image. Serve it using a TFTP server as "openwrt-3915.bin" at 192.1681.66. 5. Download & boot the OpenWrt initramfs image on the access point. $ run ramboot_openwrt 6. Wait for OpenWrt to start. 7. Download and transfer the sysupgrade image to the device using e.g. SCP. 8. Install OpenWrt to the device using "sysupgrade" $ sysupgrade -n /path/to/openwrt.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: point to externally compiled dtbs in recipesTomasz Maciej Nowak2022-09-06
| | | | | | | | | | | | | | | | Adjusting dts will cause a rebuild of whole kernel as the buildroot considers this a part of kernel source. It's a royal PITA when trying to prepare support for new device, since this takes a lot of time on slower systems. As it stands, buildroot itself, with own rule, also compiles dtbs and the results are $(KDIR)/image-$(DEVICE_DTS).dtb. With setting DEVICE_DTS_DIR to directory holding the device dts (similarly to some other targets), buildroot doesn't consider changed dts as part of kernel source and rebuilds only dtb. This really speeds up development. And since the kernel built dts are no longer used, drop the paches adding dtses to its build. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq-wifi: drop upstreamed board-2.binChristian Lamparter2022-07-15
| | | | | | | | | | The BDFs for the: GL.iNet GL-B2200 were upstreamed to the ath10k-firmware repository and landed in linux-firmware.git Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Meraki MR74Matthew Hagan2022-06-19
| | | | | | | | | | | | The Meraki MR74 is part of the "Insect" series. This device is essentially an outdoor variant of the MR33 with identical hardware, but requiring a config@3 DTS option to be set to allow booting with the stock u-boot. The install procedure is replicated from the MR33, with the exception being that the MR74 sysupgrade image must be used. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq40xx: add support for Linksys WHW01 v1Peter Adkins2022-06-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Link: https://github.com/openwrt/openwrt/pull/3682 Signed-off-by: Peter Adkins <peter@sunkenlab.com> (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add Aruba AP-365 specific BDFDavid Bauer2022-06-02
| | | | | | | | | | | | | Aruba deploys a BDF in the root filesystem, however this matches the one used for the DK04 reference board. The board-specific BDFs are built into the kernel. The AP-365 shows sinificant degraded performance with increased range when used with the reference BDF. Replace the BDF with the one extracted from Arubas kernel. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: drop upstreamed board-2.binChristian Lamparter2022-05-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BDFs for the: Aruba AP-303 ASUS RT-AC42U AVM FRITZ!Repeater 1200 Buffalo WTR-M2133HP Cell C RTL30VW D-Link DAP-2610 EnGenius EAP2200 EnGenius EMD1 EnGenius EMR3500 EnGenius EMR5000 EZVIZ CS-W3-WD1200G EUP Google Wifi Linksys MR8300 V1.0 Luma WRTQ-329ACN MobiPromo CM520-79F NEC Platforms WG2600HP3 Plasma Cloud PA1200 (updated version) Plasma Cloud PA2200 ZTE MF286D were upstreamed to the ath10k-firmware repository and landed in linux-firmware.git. Furthermore the BDFs for the: 8devices Habanero OpenMesh A62 OpenMesh A42 AVM FRITZ!Box 4040 have been updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17Ray Wang2022-04-09
| | | | | | RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5. Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ipq40xx: update E2600AC c1/c2 board张 鹏2022-03-25
| | | | | | | | Modified the radio frequency hardware part of e2600ac c1/c2, need to cooperate with the modified board.bin file, the device can work normally. Signed-off-by: 张 鹏 <sd20@qxwlan.com>
* ipq40xx: add support for FRITZ!Box 7520Andre Heider2022-03-25
| | | | | | | | | | | | | This model, also know as "1&1 HomeServer", shares the same features as 7530. The vendor firmware has artificial software limitations: only 2 of the 4 LAN-Ports are GBit, and the USB-Host is only v2.0. With OpenWrt, USB is already working at v3.0. Signed-off-by: Andre Heider <a.heider@gmail.com> (updated commit message to reflect current state) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: disable non-building tel(co Electronics) x1proChristian Lamparter2022-03-25
| | | | | | | | | | Tel(co Electronics) X1 Pro is preventing ipq40xx generic from building due to the KERNEL_SIZE. Whenever bigger kernels are possible, if lzma is supported is unknown. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Telco X1 ProNicholas Smith2022-03-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | Telco X1 Pro is a Cat12 LTE-A Pro modem router. Vendor firmware is based on a recent version of OpenWrt. Flashing is possible via CLI using sysupgrade -F -n The serial headers allow bootloader and console access Serial setting: 115200 8N1 Brief Specifications: IPQ4019 SoC 32MB flash 512MB RAM 4x gigabit LAN 1x gigabit WAN Dual-band Wave-2 wifi 2x SMA LTE antenna connectors 2x RP-SMA wifi antennas 1x USB 2.0 port 1x Reset button Serial headers installed 1x Nano SIM tray 1x Quectel EM-12G LTE-A Pro modem 1x M.2 slot attached to USB 3.0 1x internal micro SD card slot Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
* ipq40xx: add support for ZTE MF286DPawel Dembicki2022-02-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZTE MF286D is a LTE router with four gigabit ethernet ports and integrated QMI mPCIE modem. Hardware specification: - CPU: IPQ4019 - RAM: 256MB - Flash: NAND 128MB + NOR 2MB - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2 - LTE: mPCIe cat 12 card (Modem chipset MDM9250) - LAN: 4 Gigabit Ports - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem) - Serial console: X8 connector 115200 8n1 Known issues: - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs are driven by cpu. - Wifi LED is triggered by phy0tpt only - No VoIP support - LAN1/WAN port is configured as WAN - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN and WLAN0/1 Opening the case: 1. Take of battery lid (no battery support for this model, battery cage is dummy). 2. Unscrew screw placed behind battery lid. 3. Take off back cover. It attached with multiple plastic clamps. 4. Unscrew four more screws hidden behind back case. 5. Remove front panel from blue chassis. There are more plastic clamps. 6. Unscrew two boards, which secures the PCB in the chassis. 7. Extract board from blue chassis. Console connection (X8 connector): 1. Parameters: 115200 8N1 2. Pin description: (from closest pin to X8 descriptor to farthest) - VCC (3.3V) - TX - RX - GND Install Instructions: Serial + initramfs: 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3 2. Connect serial console (115200,8n1) to X8 connector. 3. Connect TFTP server to RJ-45 port. 4. Stop in u-Boot and run u-Boot commands: setenv serverip 192.168.1.3 setenv ipaddr 192.168.1.72 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock. 6. Login via ssh or serial and remove stock partitions: ubiattach -m 9 ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. Install image via "sysupgrade -n". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cosmetic changes to the commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: image: remove unused DTB_SIZE variableSungbo Eo2022-01-17
| | | | | | It is not included in DEVICE_VARS anyways. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: add RT-ACRH13 alternative name to RT-AC58UChristian Lamparter2022-01-15
| | | | | | RT-ACRH13 is another name this device was sold as (US?). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-ACRH17/RT-AC42UJoshua Roys2022-01-15
| | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d DRAM: 256 MB NAND: 128 MiB Macronix MX30LF1G18AC ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN) USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4 INPUT: 1x WPS, 1x Reset LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed with an intermediary initramfs image, the jffs2 ubi volume deleted, and then finally a sysupgrade with the final image performed. Signed-off-by: Joshua Roys <roysjosh@gmail.com> (added ALT0) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10Christian Lamparter2021-12-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | with current images, the device is no longer booting. It gets stuck in the bootloader with "Config not available" and drops to the uboot shell. |flash_type: 0 |Hit any key to stop autoboot: 0 |SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB |Config not availabale |(IPQ40xx) # This is because the default bootcmd "bootipq" will only read the first four MiB of the kernel image. With 5.10 the gzip'd kernel is slightly larger. So the part of the FIT image which had the configuration is cut off. Hence it can't find it. To update the bootcmd, you have to attach the serial console again and enter the following commands into the boot prompt: # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm" # saveenv # run bootcmd This will allow booting kernels with up to six MiB. This also allows us to drop the DEVICE_DTS_CONFIG hack we had to use. Note: uboot doesn't support LZMA. It fails with: "Unimplemented compression type 3" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for GL.iNet GL-B2200TruongSinh Tran-Nguyen2021-12-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: Add support for Teltonika RUTX10Felix Matouschek2021-11-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org>
* ipq40xx: reenable Zyxel NBG6617 by defaultChristian Lamparter2021-11-14
| | | | | | | | | The Zyxel NBG6617 already uses lzma to compress the kernel. A local build with every module enabled (either as =Y or =M) ended produced a 3058 KiB kernel (the kernel partition is 4MiB). It booted just fine, let's reenable the device. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)Richard Yu2021-11-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> Signed-off-by: Richard Yu <yurichard3839@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> [Added comment about MIBIB+128 MiB variant. Added commit message section about pcie slot. Renamed gpio-leds' subnodes and added color, function+enum properties.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: use zImage for Cell-C RTL30VWPawel Dembicki2021-11-06
| | | | | | | | | | After switch to 5.10 kernel, kernel size was too high. This patch switches Cell-C RTL30VW from uImage to zImage build. Lzma uImage wrap is required for factory booting and it must left untouched. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: disable some devices due to kernel sizeRobert Marko2021-11-03
| | | | | | | | | | Disable some of the ipq40xx devices due to their kernel size limitations. These devices fail to build with kernel 5.10 and full buildbot config. Signed-off-by: Robert Marko <robert.marko@sartura.hr> [keep gl-b1300/gl-s1300 enabled, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50Davide Fioravanti2021-11-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost identical AC3000 routers. The SRR60 has one port labeled as wan while the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a different external shape but they have an USB 2.0 port on the back. This patch has been tested only on SRS60 and RBR50, but should work on SRR60 and RBS50. Hardware -------- SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads) RAM: 512MB DDR3 FLASH: 4GB EMMC ETH: - 3x 10/100/1000 Mbps Ethernet - 1x 10/100/1000 Mbps Ethernet (WAN) WIFI: - 2.4GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x QCA9984 (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x Sync button - 1x ON/OFF button LEDS: - 8 leds controlled by TLC59208F (they can be switched on/off independendently but the color can by changed by GPIOs) - 1x Red led (Power) - 1x Green led (Power) UART: - 115200-8-N-1 Everything works correctly. Installation ------------ These routers have a dual partition system. However this firmware works only on boot partition 1 and the OEM web interface will always flash on the partition currently not booted. The following steps will use the SRS60 firmware, but you have to chose the right firmware for your router. There are 2 ways to install Openwrt the first time: 1) Using NMRPflash 1. Download nmrpflash (https://github.com/jclehner/nmrpflash) 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img file in the same folder of the nmrpflash executable 3. Connect your pc to the router using the port near the power button. 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img". Replace XXX with your network interface (can be identified by running "nmrpflash -L") 5. Power on the router and wait for the flash to complete. After about a minute the router should boot directly to Openwrt. If nothing happens try to reboot the router. If you have problems flashing try to set "10.164.183.253" as your computer IP address 2) Without NMRPflash The OEM web interface will always flash on the partition currently not booted, so to flash OpenWrt for the first time you have to switch to boot partition 2 and then flash the factory image directly from the OEM web interface. To switch on partition 2 you have to enable telnet first: 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet". 2. Connect through telent ("telnet 192.168.1.250") and login using admin/password. To read the current boot_part: artmtd -r boot_part To write the new boot_part: artmtd -w boot_part 02 Then reboot the router and then check again the current booted partition Now that you are on boot partition 2 you can flash the factory Openwrt image directly from the OEM web interface. Restore OEM Firmware -------------------- 1. Download the stock firmware from official netgear support. 2. Follow the nmrpflash procedure like above, using the official Netgear firmware (for example SRS60-V2.2.1.210.img) nmrpflash -i XXX -f SRS60-V2.2.1.210.img Notes ----- 1) You can check and edit the boot partition in the Uboot shell using the UART connection. "boot_partition_show" shows the current boot partition "boot_partition_set 1" sets the current boot partition to 1 2) Router mac addresses: LAN XX:XX:XX:XX:XX:69 WAN XX:XX:XX:XX:XX:6a WIFI 2G XX:XX:XX:XX:XX:69 WIFI 5G XX:XX:XX:XX:XX:6b WIFI 5G (2nd) XX:XX:XX:XX:XX:6c LABEL XX:XX:XX:XX:XX:69 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com> [added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved sysupgrade mmc.sh to here and renamed it, various dtsi changes] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096kSzabolcs Hubai2021-10-10
| | | | | | | | | | | | | | | | | | | | | | | | In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub, Adrian noted [0] that these GL.iNet Conexa series devices, GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped uImage kernel went above 4096k. While notifying the vendor about this problem [2], I tested all U-Boot releases from GL.iNet: - they really fail to boot kernel above 4096k - they don't support lzma: "Unimplemented compression type 3" - but they boot zImage Using zImage (xz compression) the kernel is 2909k which is more than a megabyte away from the KERNEL_SIZE := 4096k limit. The gzip compressed version would be 4116k. [0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776 [1]: commit 7b1fa276f5a2 ("ipq40xx: add testing support for kernel 5.10") [2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619 Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200Sven Eckelmann2021-09-12
| | | | | | | | | | | The board data file for the Plasma Cloud PA2200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: 4871fd2616ac ("ipq40xx: add support for Plasma Cloud PA2200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200Sven Eckelmann2021-09-12
| | | | | | | | | | | The board data file for the Plasma Cloud PA1200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: ea5bb6bbfee0 ("ipq40xx: add support for Plasma Cloud PA1200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Select correct board-2.bin for EnGenius EMR3500Sven Eckelmann2021-09-12
| | | | | | | | | The board data file for the EnGenius EMR3500 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 3f61e5e1b97e ("ipq40xx: add support for EnGenius EMR3500") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Select correct board-2.bin for EnGenius EMD1Sven Eckelmann2021-09-12
| | | | | | | | | The board data file for the EnGenius EMD1 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 51f303597839 ("ipq40xx: add support for EnGenius EMD1") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: fix Edgecore ECW5211 bootStijn Tintel2021-08-18
| | | | | | | The bootloader will look for a configuration section named ap.dk01.1-c2 in the FIT image. If this doesn't exist, the device won't boot. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Powered by cgit, Themed by Ted Yin.