aboutsummaryrefslogtreecommitdiff
path: root/target/linux/ipq40xx/base-files
Commit message (Collapse)AuthorAge
* ipq40xx: convert Engenius EAP1300 to DSACorey Minyard2024-05-06
| | | | | | | | This commit converts the EAP1300 to DSA setup. Signed-off-by: Corey Minyard <minyard@acm.org> Link: https://github.com/openwrt/openwrt/pull/15358 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: add support for Linksys WHW03 V1Rodrigo Balerdi2024-05-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: ========= SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA9886 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8510 (A10) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash: Samsung KLM4G1FEPD (4GB eMMC) RAM (NAND): 512MB LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). Ethernet: ========= The device has 2 ethernet ports, configured as follows by default: - left port: WAN - right port: LAN Wifi: ===== The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Bluetooth and Zigbee: ===================== Configuration included but not tested. Storage: ======== For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB eMMC partition (of which there are two copies, see below). You can also use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit. During very limited tests, stock firmware did not mount this partition. However, backing up its stock content before use is recommended anyway. Firmware: ========= The device uses a dual firmware mechanism: it automatically reverts to the previous firmware after 3 failed boot attempts. You can switch to the inactive firmware copy by changing the "boot_part" U-Boot environment variable. You can also do it by turning on the device for a couple of seconds and then back off, 3 times in a row. Installation: ============= OpenWrt's "factory" image can be installed via the stock web UI: 1. Login to the UI. (The default password is printed on the label.) 2. Enter support mode by clicking on the "CA" link at the bottom. 3. Click "Connectivity", "Choose file", "Start", and ignore warnings. This port is based on work done by flipy (https://github.com/flipy). Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15345 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: Add support Netgear LBR20Marcin Gajda2024-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem. SoC Type: Qualcomm IPQ4019 RAM: 512 MiB Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC) Bootloader: U-Boot Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink WiFi class AC2200: - radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels - radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz - radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on. Ethernet: 2x1GbE (WAN/LAN1, LAN2) LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white USB ports: No Buttons: 2 Reset and SYNC(WPS) Power: 12 VDC, 2,5 A Connector type: Barrel OpenWRT Installation 1. Simplest way is just do upgrade from webpage with *factory.img 2. You can also do it with standard tool for Netgear's debricking - NMPRFlash 3. Most advanced way is to open device , connect to UART console and : - Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10) - Connect serial console (115200,8n1) to UART connector - Connect TFTP server to RJ-45 port - Stop in u-Boot and run u-Boot command: > setenv serverip 192.168.1.10 > set fdt_high 0x85000000 > tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb > bootm 0x83000000 - Login via ssh - upload or download *sysupgrade.bin ( like wget ... or scp transfer) - Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”) Back to Stock - Download firmware from official Netgear's webpage , it will be *.img file after decompressing. - Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash ) Open the case - Unscrew nuts and remove washers from antenna's conectors. - There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it - Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that. - PCB is screwed with 4Pcs of Torx T10 screws - Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires) - On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg ) BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org. Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* ipq40xx: update ASUS RT-AC58U leds DTS nodesChristian Lamparter2023-12-02
| | | | | | | | | | | | - use color, function, function-enumerator properties. - removes the label properties from LED nodes. - add panic-indicator to the blue power/status LED. Note: yes this brings the combined LAN/"switch" LED sort of back, though I fully admit, it's a bit jank. Do you know a better option? then please tell/make a PR! Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Extreme Networks WS-AP391x series APsGlen Lee2023-09-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This in a single image to run many types of hardware in the AP391x series (AP3912/AP3915/AP3916/AP3917/AP7662). Hardware -------- Qualcomm IPQ4029 WiSoC 2T2R 802.11 abgn 2T2R 802.11 nac Macronix MX25L25635E SPI-NOR (32M) 512M DDR3 RAM 1-4x Gigabit Ethernet Senao EXT1025 HD Camera (AP3916 only) USB 2.0 Port (AP3915e only) 1x Cisco RJ-45 Console port - except for AP3916 and AP3912 where there is no external serial console and it is TDB how to solder one. Possibly J12 is UART with pin1 = 3.3V, pin2 = GND, pin3 = TXD, pin4 = RXD. - Settings: 115200 8N1 Installation With Serial Console -------------------------------- 1. Attach to the Console port. Power up the device and press the s key to interrupt autoboot. 2. The default username / password to the bootloader is admin / new2day 3. Check uboot variables using printenv, and update if necessary: $ setenv AP_MODE 0 $ setenv WATCHDOG_COUNT 0 $ setenv WATCHDOG_LIMIT 0 $ setenv AP_PERSONALITY identifi $ setenv serverip <SERVER_IPADDR> $ setenv ipaddr <UNIQUE_IPADDR> $ setenv MOSTRECENTKERNEL 0; ## OpenWRT only uses the primary image $ saveenv $ saveenv ## 2nd time to write the secondary copy 4. On the TFTP server located at <SERVER_IPADDR>, download the OpenWrt initramfs image. Rename and serve it as vmlinux.gz.uImage.3912 5. TFTP boot the OpenWrt initramfs image from the AP serial console: $ run boot_net 6. Wait for OpenWrt to start. Internet port sw-eth5 is assiged to LAN bridge and sw-eth4 (if available) is assigned to WAN. The LAN port will use default IP address 192.168.1.1 and run a DHCP server. If you already have a working DHCP server or already have 192.168.1.1 on your network you MUST DISCONNECT the LAN cable from your active network immediately after the power/status LED turns green! At this point, you need to temporarily reconfigure the AP to have a way to transfer the OpenWRT sysupgrade image to it. Reconfigure the newly converted OpenWRT AP using serial console or plug in a PC to a sw-eth5 as a separate network. Note -- the LAN/WAN port assignments were designed to make it possible to convert to OpenWRT without serial console and using a common firmware image for many AP models -- they may not make the most sense when fully deployed. 7. Download and transfer the sysupgrade image to the device using e.g. SCP. 8. Install OpenWrt to the device using "sysupgrade" $ sysupgrade -n /path/to/openwrt.bin 9. After it boots up again, as in step 6, connect to AP and reconfigure for final deployment. This build supports APs in the AP391x series and similar such as WiNG AP7662. Ethernet devices within OpenWRT are named "sw-eth1" thru "sw-eth5". Mapping from OpenWRT internal naming to external naming on the case is as follows: ``` |sw-eth1|sw-eth2|sw-eth3|sw-eth4|sw-eth5 ------------+-------+-------+-------+-------+------- AP3917 | | | | GE2 | GE1 ------------+-------+-------+-------+-------+------- AP7662 | | | | GE2 | GE1 ------------+-------+-------+-------+-------+------- AP3916 | | | | CAM* | GE1 ------------+-------+-------+-------+-------+------- AP3915 | | | | | GE1 ------------+-------+-------+-------+-------+------- AP3912 | | P1 | P2 | P3 | LAN1 ------------+-------+-------+-------+-------+------- ``` By default sw-eth4 is mapped to WAN. All others are assigned to the LAN. CAM* - On AP3916, sw-eth4 is the camera's interface. You should reconfigure this to be on LAN after OpenWRT boots from flash. Installation Without Serial Console ----------------------------------- The main premise is to set u-boot environment variables using the Extreme Networks firmware's rdwr_boot_cfg program. $ rdwr_boot_cfg Utility to manipulate the boot ROM config blocks All errors are written to the sytem log file (/tmp/log/ap.log) ``` Usage: rdwr_boot_cfg <read_all|read_var|read_var_f|write_var|rm_var> ... read_all read the entire active block read_var <var> read a single variable from the active block read_var_f <var> read a single variable from the active block (formatted) write_var <var=val> write a single variable/value pair to both blocks rm_var <var> delete a single variable from both blocks ``` WARNING: Be very sure you have set the u-boot environment correctly. If not, it can only be fixed by attaching serial console! Be aware that the Extreme Networks shell environment will automatically reboot every 5 minutes if there is no controller present. Read and understand these steps fully before attempting. It is easy to make mistakes! 1. Place the OpenWRT initramfs on the TFTP server and name it as vmlinux.gz.uImage.3912 2. Boot up to Extreme Networks WING-Campus mode OS. Port GE1/LAN1 will be a DHCP **client**. Find out the IP address from your DHCP server and SSH in. Default user/passwd is admin/new2day or admin/admin123. If it is booting to WING-Distributed mode, use this command to convert to Campus mode. $ operational-mode centralized 3. Upon bootup you have about 5mins to changed these u-boot variables if necessary using the rdwr_boot_cfg command in Linux shell: $ rdwr_boot_cfg write_var AP_MODE=0 $ rdwr_boot_cfg write_var MOSTRECENTKERNEL=0 $ rdwr_boot_cfg write_var WATCHDOG_COUNT=0 $ rdwr_boot_cfg write_var WATCHDOG_LIMIT=0 $ rdwr_boot_cfg write_var AP_PERSONALITY=identifi $ rdwr_boot_cfg write_var serverip=<SERVER_IPADDR> $ rdwr_boot_cfg write_var ipaddr=<UNIQUE_IPADDR> $ rdwr_boot_cfg write_var bootcmd="run boot_net" 4. Reboot AP. 5. Connect PC with ethernet to GE1/LAN1 port. You should get a DHCP address in the 192.168.1.x range and should be able to SSH to the new OpenWRT TFTP recovery/installation shell. 6. At this point, u-boot is still set to TFTP boot, so you have to replace the TFTP image with the original Extreme Networks image so that you can change the u-boot environment. See the instructions for Extracting Extreme Networks firmware image. DON'T REBOOT YET! 7. Next you must follow steps 6 thru 8 from the Installation with serial console. After which you should have OpenWRT installed to primary flash firmware. 8. Now Reboot. This time it will boot using TFTP into Extreme Networks image. You may need to reconnect cables at this point -- GE1/LAN1 will be a DHCP **client** and you can SSH in -- just like step 2. Get the IP address from you own DHCP server. 9. Set u-boot env as follows: $ rdwr_boot_cfg write_var MOSTRECENTKERNEL=0 $ rdwr_boot_cfg write_var WATCHDOG_COUNT=0 $ rdwr_boot_cfg write_var bootcmd="run boot_flash" 10. Reboot AP. This time it should be into OpenWRT. GE1/LAN1 will be a DHCP **server** and have static IP 192.168.1.1 -- just like step 5. 11. SSH into the LAN port and reconfigure to final configuration. Don't make any changes that prevent you from SSH or Luci access! Restoring Extreme Networks firmware ----------------------------------- Assuming you have the original Extreme Networks image: 1. Login to OpenWRT shell 2. scp the Extreme Networks packaged firmware image file AP391x-*.img to /tmp 3. Extract the firmware uimage file: $ tar xjf AP391x-*.img vmlinux.gz.uImage 4. Force run sysupgrade: $ sysupgrade -F /tmp/AP391x-*.img / 5. Restore the u-boot varable(s): $ rdwr_boot_cfg write_var WATCHDOG_LIMIT=3 USB 2.0 Port on AP3915e ----------------------- Enable this by setting LED "eth:amber_or_usb_enable" to ALWAYS ON. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Glen Lee <g2lee@yahoo.com>
* ipq40xx: ZTE MF282 Plus fix sysupgradeAndreas Böhler2023-09-25
| | | | | | | While adding support for the MF282 Plus, an entry in platform.sh was overlooked - this fixes sysupgrade on this devices. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq40xx: ZTE MF287 fix sysupgradeAndreas Böhler2023-09-25
| | | | | | | While refactoring support for the MF287 series, an entry in platform.sh was overlooked - this fixes sysupgrade on this devices. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq4019: add support for ZTE MF282 Plus aka DreiTubeAndreas Böhler2023-09-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF282 Plus is a LTE router used (exclusively?) by the network operator "3". It is very similar to the MF286/MF287 but in the form factor of the MF282. Specifications ============== SoC: IPQ4019 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 1x GBit LAN LTE: ZTE Cat6 WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config WiFi 1: from config + 1 WiFi 2: from config + 2 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x84000000 openwrt.bin bootm 0x84000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m9 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd9 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd9 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock9 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 9 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to the MF286R, it provides an RNDIS interface and an AT interface. Other Notes =========== There is one GPIO Switch "Power button blocker" which, if enabled, does not trigger a reset of the SoC if the modem reboots. If disabled, the SoC is rebooted along with the modem. The modem can be rebooted via the exported GPIO "modem-reset" in /sys/class/gpio. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq40xx: refactor ZTE MF287 seriesAndreas Böhler2023-09-19
| | | | | | | | The ZTE MF287 requires a different board calibration file for ath10k than the ZTE MF287+. The two devices receive their own DTS, thus the device tree is slightly refactored. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq40xx: add support for YYeTs LE1Chukun Pan2023-09-18
| | | | | | | | | | | | | | | | | | | Hardware Highlights: SoC: Qualcomm IPQ4019 717 MHz RAM: 512M NT5CC256M16ER-EK Flash: 32M SPI NOR MX25L25635F WIFI1: 2.4 GHz 2T2R integrated WIFI2: 5 GHz 2T2R integrated Ethernet: QCA8075 (4x LAN, 1x WAN) LEDS: power, wlan2g, wlan5g, usb USB: 1x 3.0 Button: Reset Installation: Upload factory.bin in stock firmware's upgrade page, and this will take a few minutes. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ipq40xx: add support for Netgear RBX40Thomas Makin2023-09-16
| | | | | | | | This adds support for the RBR40 and RBS40 (sold together as RBK40), two netgear routers identical to SRR60/SRS60 in all but antennae (and hardware id). See 2cb24b3f3c for details. Signed-off-by: Thomas Makin <halorocker89@gmail.com>
* ipq40xx: convert devolo Magic 2 WiFi next to DSAThomas Bong2023-09-03
| | | | | | | | | | Renamed the interfaces to match the other devices. Name the interface connected to the builtin G.hn chip 'ghn'. This might toggle at runtime while the G.hn chip is in the bootloader. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
* ipq4019: add support for ZTE MF287 Pro aka DreiNeo ProAndreas Böhler2023-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287 Pro is a LTE router used (exclusively?) by the network operator "3". It is very similar to the MF287+, but the hardware layout and partition layout have changed quite a bit. Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 WiFi: 802.11a/b/g/n/ac SoC-integrated USB: 1x 2.0 MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m17 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd17 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 17 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Other Notes =========== Contrary to the stock firmware, the USB port on the back can be used. There is one GPIO Switch "Power button blocker" which, if enabled, does not trigger a reset of the SoC if the modem reboots. If disabled, the SoC is rebooted along with the modem. The modem can be rebooted via the exported GPIO "modem-reset" in /sys/class/gpio. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq40xx: remove DK01 and DK04 boardsRobert Marko2023-08-15
| | | | | | | | | | | | | | | | | DK01 and DK04 board support has been in a form of 2 patches that we have been carrying for a long time. Both of the patches contain weird changes, dont follow any DT syntax and I honestly doubt they are even valid. DK01 and DK04 also have not been converted to DSA even after a long time and I doubt that anybody in the community even has these boards as they are QCA reference boards that are not even obtainable anymore. Since patches for these 2 boards have been just causing us pain when trying to update the kernel to a new major release or even point releases lets remove the support for these boards, and if there are users they can easily be reinstated. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add support for Teltonika RUTX50David Bauer2023-07-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M Flash: 16MB SPI-NOR (W25Q128) 128MB SPI-NAND (XTX) WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac) ETH: 4x LAN ; 1x WAN (Gigabit) CELL: Quectel RG501Q 3G/4G/5G UART: Available on the goldfinger connector (Pinout silkscreened) 115200 8N1 3V3 - Only connect RX / TX / GND Installation ------------ 1. Enable SSH in the Teltonika UI (System --> Administration --> Access Control) 2. Check from which partition set the device is currently running from. $ cat /proc/boot_info/rootfs/primaryboot In case this output reads 0, install a Software update from Teltonika first. After upgrade completion, check this file now reads 1 before continuing. 2. Transfer the OpenWrt factory image to the device using scp. Use the same password (user root!) as used for the Web-UI. $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp 3. Connect to the device using ssh as the root user. 4. Install OpenWrt by writing the factory image to flash. $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin 5. Instruct the bootloaer to boot from the first partition set. $ echo 0 > /proc/boot_info/rootfs/primaryboot $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin $ mtd write /tmp/bootconfig.bin /dev/mtd2 $ mtd write /tmp/bootconfig1.bin /dev/mtd3 6. Reboot the device. $ reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq4019: add support for ZTE MF287+ aka DreiNeoAndreas Böhler2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq40xx: convert Buffalo WTR-M2133HP to DSAYanase Yuki2023-06-01
| | | | | | This commit convert WTR-M2133HP to DSA setup. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq40xx: add e2600ac c2 to dsa张 鹏2023-05-29
| | | | | | | | Convert E2600ac c2 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: add e2600ac c1 to dsa张 鹏2023-05-29
| | | | | | | | Convert E2600ac c1 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: convert EZVIZ CS-W3-WD1200G-EUP to DSAChristian Lamparter2023-05-20
| | | | | | Convert the repeater to DSA. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: convert AVM FRITZ!Repeater 3000 to DSANick Hainke2023-05-03
| | | | | | Convert the repeater to DSA. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert GL-AP1300 to DSANick Hainke2023-04-24
| | | | | | | | | | Convert GL-AP1300 to DSA and enable it. While working on it rename the GL-AP1300 leds from green to white. Tested-by: Rob White <rob@blue-wave.net> Tested-by: Robert Sommer <frauhottelmann@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert AP-365 to DSADavid Bauer2023-04-15
| | | | | | | | | Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as the board design is pretty much the already updated AP-303. Run-tested on the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: fix Linksys upgrade, restore config stepMichael Trinidad2023-04-11
| | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx and ipq806x devices using the linksys.sh script. Fixes: 8634c1080d50 ("ipq40xx: Fix Linksys upgrade, restore config step") Fixes: 2715aff5df83 ("ipq806x: Fix Linksys upgrade, restore config step") Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
* ipq40xx: Fix Linksys upgrade, restore config stepJeff Kletsky2023-03-26
| | | | | | | | | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This was restored for some devices in commit 84ff6c90dda1 ("base-files: bring back nand_do_upgrade_success"). This restored preservation of config for ipq40xx devices using the linksys.sh script. Other devices and targets have not been examined. Closes: #11677 Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code") Tested-on: EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> (checkpatch nitpick) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Wallystech DR40x9Robert Marko2023-03-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* ipq40xx: convert Netgear EX6100/EX6150 v2 to DSADavid Bauer2023-03-08
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: replace /sys/devices/virtual/ubi by /sys/class/ubiDaniel Golle2023-02-15
| | | | | | | | | | Starting from Linux Kernel version 6.3 UBI devices will no longer be considered virtual, but rather have an MTD device parent. Hence they will no longer be listed under /sys/devices/virtual/ubi which is used in multiple places in OpenWrt. Prepare for future kernels by using /sys/class/ubi instead of /sys/devuces/virtual/ubi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: convert Extreme AP3915i to DSAJames Andrewartha2023-01-17
| | | | | | Convert and re-enabled Extreme AP3915i to DSA. Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
* ipq40xx: add DSL support for FritzBox 7530Martin Schiller2023-01-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set up MAC, LED, settings and default packages for DSL usage, similar to the lantiq target. Due to licensing uncertainty, we do not include the firmware files for the DSL drivers. To have a working DSL setup, follow the instructions below. Download the firmware files locally: mkdir -p files/lib/firmware/09a9 wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin For people building their own images: Run the above commands in the root of your local OpenWrt clone, and the firmware files will be part of the resulting images. For people downloading images: Copy the firmware files onto the router once it's booted up: scp -O -r files/lib/firmware root@fritz:/lib Reboot the device afterwards. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [cleaned up] Signed-off-by: Andre Heider <a.heider@gmail.com> [set up LED] Signed-off-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add support for Linksys WHW03 V2Vincent Tremblay2023-01-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: Add support ZTE MF18AMarcin Gajda2023-01-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* ipq40xx: sysupgrade: allow flashing Linksys factory firmwareTony Ambardar2022-12-31
| | | | | | | | | | | | | | | | | Allow forced flashing of a factory firmware image, after checking for the correct FIT magic header and Linksys board-specific footer. Details of the footer are already described in scripts/linksys-image.sh. This is convenient as it avoids using a TFTP server or OEM GUI, and allows restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA migration and kernel repartition) directly from the command line. Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: migrate Linksys WHW01 to DSA and re-enableTony Ambardar2022-12-31
| | | | | | | | | Convert Linksys WHW01 network configuration to DSA and re-enable builds. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix up Linksys WHW01 board name, device definitionTony Ambardar2022-12-31
| | | | | | | | | | | | | | Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: re-enable EA6350v3, EA8300, MR8300 buildsTony Ambardar2022-12-31
| | | | | | | | | | | | | | | | | | | | | | | | | Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300, and correspondingly reduce the rootfs size by 2 MB: * modify partition definitions in related .dts files * modify device kernel/image sizes in generic.mk Update to compat-version 2.0 to force factory image usage on sysupgrade, noting the current version 1.1 is an unreleased update for DSA migration. Also update the compat-version message, explaining the need to run one of the following console commands to update U-Boot's kernel-size variable before flashing the OpenWrt factory image. fw_setenv kernsize 500000 # (OpenWrt command line) setenv kernsize 500000 ; saveenv # (U-Boot serial console) Finally, re-enable the 3 devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: convert Aruba AP-303H to DSA and enable target againNick Hainke2022-12-29
| | | | | | | | | The target was disabled since noone did the DSA conversion. Add the conversion and enable it again. Tested-by: John Walshaw <jjw@myself.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ipq40xx: Convert plasmacloud,pa2200 to DSASven Eckelmann2022-11-13
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa2200Sven Eckelmann2022-11-13
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert plasmacloud,pa1200 to DSASven Eckelmann2022-11-13
| | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa1200Sven Eckelmann2022-11-13
| | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for openmesh,a62Sven Eckelmann2022-11-12
| | | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for openmesh,a42Sven Eckelmann2022-11-12
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a62 to DSASven Eckelmann2022-11-12
| | | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a42 to DSASven Eckelmann2022-11-12
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: D-Link DAP-2610: convert to DSAGuillaume Lefebvre2022-11-12
| | | | | | | Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: add support for MikroTik hAP ac3 LTE6 kitCsaba Sipos2022-10-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD (hAP ac³ LTE6 kit), an indoor dual band, dual-radio 802.11ac wireless AP with built-in Mini PCI-E LTE modem, one USB port, five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac3_lte6_kit for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port - 1x USB Type A port - 1x Mini PCI-E port (supporting USB) - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6) Installation: Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6). 0. Export your MikroTik license key (in case you want to use the device with RouterOS later) 1. Boot the initramfs image via TFTP 2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder 3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin 4. Recovery to factory software is possible via Netinstall: https://help.mikrotik.com/docs/display/ROS/Netinstall Signed-off-by: Csaba Sipos <metro4@freemail.hu>
* ipq40xx: convert to DSA and enable Netgear Orbi devicesDavide Fioravanti2022-10-25
| | | | | | | | | | Convert to DSA and enable again Netgear Orbi devices: - RBR50 - RBS50 - SRR60 - SRS60 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Powered by cgit, Themed by Ted Yin.