aboutsummaryrefslogtreecommitdiff
path: root/target/linux/bmips/bcm63268/base-files/etc/board.d
Commit message (Collapse)AuthorAge
* treewide: simplify kernel version number comparisonsShiji Yang2025-07-14
| | | | | | | | | Directly call the function "get_linux_version()" to get the integer kernel version number. Signed-off-by: Shiji Yang <yangshiji66@outlook.com> Link: https://github.com/openwrt/openwrt/pull/19172 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bmips: use wan ports as standalone portsJonas Gorski2025-06-07
| | | | | | | | | | | | | | | | With the recent fixes backported to 6.12, b53 ports should now fully work as standalone ports outside of a switch. So move them out of the switch and use them as standalone ports, which makes configuring easier as VLANs don't need to be defined and reserved anymore to use the wan port. Tested on DGND3700v1. While most devices do not define a wan port, I dropped the ucidef_set_bridge_device() from all devices for consistency. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* bmips: update files for kernel 6.12Álvaro Fernández Rojas2025-05-29
| | | | | | | | | | | - Update subtarget configs for kernel 6.12. - Refresh patches for kernel 6.12. - Drop 210-revert-macronix-nand-block-protection.patch since brcmnand no longer implements low level ops. - Adapt bcm63268 gpio switches for 6.12 numbering. - Add b53 pending patches from Jonas Gorski to fix system hangs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for Actiontec T1200HKyle Hendry2025-04-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Broadcom BCM63168 dual 400MHz MIPS - Flash: 128MB NAND ESMT F59L1G81A - RAM: 128MB DDR3 - Ethernet: 5x 1000M - Wifi: BCM435F - 1x USB 2.0 port - 2x Button - 11x LED - Coax HPNA (unsupported) - RJ11 xDSL (unsupported) Install instructions: The booloader will only install signed firmware so the image has to be manually flashed. - Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image - Interrupt the bootloader and run from RAM with r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf - On the openwrt console, copy the wfi image using wget/tftp/scp, i.e scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/ - Erase half the flash partition where openwrt will be installed with flash_erase -j /dev/mtd1 0 491 - Flash the openwrt image with nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin - Reboot - Interrupt the bootloader again and use the c command to boot from previous firmware if vendor image is loaded Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com> [Minor improvements to DTS file] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for Sagem F@ST3864OPHang Zhou2024-06-26
| | | | | | | | | | | | | | | | | | | Specifications: * SoC: BCM63168 * RAM: NT5CC64M16GP-DI, DDR3 128MiB * NAND: W29N01HVSINA, 128MiB * Ethernet: 4x1000M LAN, 1x 1000M WAN * Serial interface: on board but not populated, 3.3V, 115200, 8N1 Notes: * Use DSA for VLAN and switches * Ethernet ports and USB works * gpio-leds are not working * WLAN, xDSL, and FXS are not going to work Signed-off-by: Hang Zhou <929513338@qq.com> [refactor, reorder, drop unneeded or not working stuff] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for SmartRG SR505nKyle Hendry2024-03-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Broadcom BCM63168 dual 400MHz MIPS - Flash: 16MB SPI NOR W25Q128WFG - RAM: 128MB DDR3 W631GG6KB-15 - Ethernet: 1x 1000M, 3x 100M - Wifi: BCM435F - 1x USB 2.0 port - 3x Button - 12x LED Flashing via serial - Connect to the 3.3V TTL UART on the board (J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1 - Press any key in the serial console when powering up the board to enter the CFE prompt - Configure an interface on your workstation to static IP 192.168.1.100 and connect it to the board - Start a TFTP server with the firmware image - On the CFE prompt, enter the command "f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin" Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com> [Remove unneeded LED labels] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for Comtrend VG-8050Álvaro Fernández Rojas2023-06-16
| | | | | | | | | | | | | | | | | | | | | | | | | | The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM63169 - CPU: dual core BMIPS4350 @ 400Mhz - RAM: 128 MB DDR - Flash: 128 MB NAND - LAN switch: Broadcom BCM53125, 5x 1Gbit - Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn - USB: 1x 2.0 (optional) - Buttons: 2x (reset) - LEDs: yes - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the power switch. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add subtargets for each SoCÁlvaro Fernández Rojas2023-04-10
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one with its own specific drivers, so instead of having a huge kernel supporting all of them, let's switch to a subtarget per SoC like other OpenWrt targets. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Powered by cgit, Themed by Ted Yin.