aboutsummaryrefslogtreecommitdiff
path: root/package
Commit message (Collapse)AuthorAge
* mac80211: remove non-upstream antenna gain configuration patchFelix Fietkau2023-08-30
| | | | | | | | | It seems that this was not functioning properly and was likely completely unused. Keeping this out of tree also introduced some annoying churn when updating, because of the iw nl80211.h sync patch. If this is needed, it will be reintroduced when/if it is added upstream Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: enable vfio and vfio-pci for armsr-armv8Mathew McBride2023-08-29
| | | | | | | | | Arm platforms with the right hardware blocks (such as GICv3.0+ interrupt controller and SMMU/IOMMU) are able to use vfio-pci to pass through PCI devices to a VM. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* kernel: vfio: remove unneeded enable_unsafe_noiommu_mode parameterMathew McBride2023-08-29
| | | | | | | | | | | | | The vfio module only exposes the enable_unsafe_noiommu_mode parameter if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module will complain about an unknown parameter: vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored As CONFIG_VFIO_NOIOMMU is disabled by the module package, we can remove the module loading parameter. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* arm-trusted-firmware-mediatek: enable built-in 2.5G PHY on MT7988Daniel Golle2023-08-28
| | | | | | | | | | Always enable built-in 2.5G PHY on MT7988 for now, so that it can be used. In future it would be nice to be able to switch power and MDIO access via address 0 at run-time in Linux, both, to be able to use external PHYs at address 0 and to reduce power consumption on systems not using the built-in 2.5G PHY. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: fix dependency on TF-A for MT7988 RFB (sdmmc)Daniel Golle2023-08-28
| | | | | | | | | The U-Boot build for the MT7988 reference board booting from SD card wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build even though the 'comb' variant is used. Fix that dependency. Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add builds for UniFi 6 LR v2 and v3Daniel Golle2023-08-28
| | | | | | | While the v2 is nearly identical to v1, v3 uses a different PHY and needs a different build for Ethernet to work in U-Boot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: build fully-featured U-Boot for MT7988 RFBDaniel Golle2023-08-28
| | | | | | | | | | | | | | | | | | Select many potentially useful options for the MT7988 RFB U-Boot builds. The resulting loader is intended as a development tool and intends to be generic. It does *not* have a default bootcmd set, but allows to boot pretty much everything, including EFI executables. To install this U-Boot build to the eMMC: opkg install mmc-utils partx-utils mmc bootpart enable 1 1 /dev/mmcblk0 echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0 dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0 partx -a /dev/mmcblk0 dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ltq-vdsl-vr11-mei: fix compilation error with kernel 6.1Andre Heider2023-08-27
| | | | | | Define the old PDE_DATA marco to the new pde_data function. Signed-off-by: Andre Heider <a.heider@gmail.com>
* vrx518_tc: fix compilation error with kernel 6.1Andre Heider2023-08-27
| | | | | | | Define the old PDE_DATA marco to the new pde_data function and conditionally use the newer APIs. Signed-off-by: Andre Heider <a.heider@gmail.com>
* vrx518_ep: fix compilation error with kernel 6.1Andre Heider2023-08-27
| | | | | | | Unconditionally use the newer APIs, since our oldest supported kernel contains them too. Signed-off-by: Andre Heider <a.heider@gmail.com>
* ltq-ifxos: fix compilation error with kernel 6.1Andre Heider2023-08-27
| | | | | | Conditionally use the newer APIs. Signed-off-by: Andre Heider <a.heider@gmail.com>
* uboot-rockchip: fix swig dependency for ROCK64Antonio Flores2023-08-27
| | | | | | Pre build files to fix swig dependency. Signed-off-by: Antonio Flores <antflores627@gmail.com>
* uboot-rockchip: add support for PINE64 ROCK64Antonio Flores2023-08-27
| | | | | | Add uboot support for PINE64 ROCK64, rockchip rk3328 board. Signed-off-by: Antonio Flores <antflores627@gmail.com>
* uboot-sunxi: bump to 2023.04Zoltan HERPAI2023-08-26
| | | | | | | | | | | | | | | | | Compile-tested: all boards Runtime-tested: - Cortex-A8: pcDuino - Cortex-A7: Bananapro, Bananapi M3 - Cortex-A53:Pine64+ Notes: - binman tries to add firmware for the SCP (system control processor), which we don't build, and is optional for the boot process on 64-bit. Disable this via setting the SCP envvar to /dev/null. For further info, see [1] . [1] https://github.com/u-boot/u-boot/blob/master/board/sunxi/README.sunxi64 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* kernel: add vhost-net moduleMathew McBride2023-08-26
| | | | | | | | | | | | | | | | vhost-net is used to accelerate traffic to virtualisation guests that use the virtio-net network card in QEMU. Generally it is invoked by specifying "vhost=on" to a QEMU -netdev device: qemu-system-aarch64 -nographic -M virt -cpu host \ --enable-kvm -bios u-boot.bin -smp 1 -m 2048 \ -drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \ -device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \ -netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on" Signed-off-by: Mathew McBride <matt@traverse.com.au>
* arm-trusted-firmware-mvebu: bump to v2.9Robert Marko2023-08-26
| | | | | | We are using the outdated 2.7 TF-A, so lets update to current v2.9 version. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: update CM3 GCC to 12.3rel1Robert Marko2023-08-26
| | | | | | | | | We are using the outdated 11.2 GCC for CM3, lets update to the current 12.3rel1 version from ARM [1]. [1] https://developer.arm.com/downloads/-/arm-gnu-toolchain-downloads Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump cryptopp to version 8.8Robert Marko2023-08-26
| | | | | | | We are using the outdated Crypto++ version 8.5, so lets update to the current version 8.8. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump mox-boot-builder to current versionRobert Marko2023-08-26
| | | | | | | | | | | | | | | | | We have to move to use git clone as there are no newer tagged releases. Changes: 604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi- b9b9419 Tidy up license information 0290b2c wtmi: Fix typo a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal) f654082 wtmi: Add const qualifier to isr_vector 4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz 189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up 3dac4fe wtmi: Fix detection of Armada 3720 Devel Board 3ca4dfa Bump mox-imager commit Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump mv-ddr-marvell to current versionRobert Marko2023-08-26
| | | | | | | | Changes: 1de442d Convert floating point operations to integer operations ce6770d Modify mv_ddr4_calibration_validate function body to match function header Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump a3700-utils to current versionRobert Marko2023-08-26
| | | | | | | | Changes: a3e1c67 wtmi: Fix linker output sections f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mac80211: Add ath11k to the help text of ATH_DEBUGJacob Aharon2023-08-25
| | | | | | | ATH_DEBUG package is required to debug ath11k. Fixes: 93ae4353cdf6 ("mac80211: add ath11k PCI support") Signed-off-by: Jacob Aharon <ah.jacob@gmail.com>
* uboot-envtools: fix parallel buildingRobert Marko2023-08-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recent envtools update to 2023.07.02 has introduced a breakage when trying to parallel build with the following error: /bin/sh: line 1: scripts/basic/fixdep: No such file or directory Luckily it can easily be reproduced locally via a simple script so it was not hard to bisect it down to upstream commit [1]. However, its not that commits fault, it just uncovered an issue with the way we have been building envtools for a long time, maybe even from the package introduction. The issue is that we are trying to build envtools as one of the U-Boot no-dot-config-targets but envtools was newer a valid target for it but since we were creating the config headers that were not actually used it was actually building all this time. Since the blamed commit [1] a tool called printinitialenv is built and now a proper config is actually required in order for prerequisites to get built properly. So, in order to properly fix this (Hopefully for good) lets stop pretending that envtools are a valid no-dot-config-targets target and use the tools-only defconfig which is meant exactly for just building the tools. This will make a minimal config for the U-Boot sandbox target and then envtools will build just fine in parallel mode (I tested with 32 threads). We do hovewer need to override the ARCH passed by OpenWrt and set it to sandbox as otherwise U-Boot will not find the required headers because the ARCH is being overriden to an incorrect one. [1] https://source.denx.de/u-boot/u-boot/-/commit/40b77f2a3ac13a7547c1b7c9c51a4090869de8f4 Fixes: 9db033005210 ("uboot-envtools: update to 2023.07.02") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mt76: update to the latest versionFelix Fietkau2023-08-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | bdf7ca5db707 wifi: mt76: mt7921: move common register definition in mt792x_regs.h ae15d5c6b567 wifi: mt76: mt7921: convert acpisar and clc pointers to void 02515b6b90f0 wifi: mt76: mt7921: rename mt7921_vif in mt792x_vif 6ed8a8bdc7b6 wifi: mt76: mt7921: rename mt7921_sta in mt792x_sta 80234e64e7c5 wifi: mt76: mt7921: rename mt7921_phy in mt792x_phy 2485b4222d3d wifi: mt76: mt7921: rename mt7921_dev in mt792x_dev c6fd7cde77e0 wifi: mt76: mt7921: rename mt7921_hif_ops in mt792x_hif_ops 1a1a57b5f8c4 wifi: mt76: mt792x: move shared structure definition in mt792x.h 68508aab4241 wifi: mt76: mt7921: move mt792x_mutex_{acquire/release} in mt792x.h ff306af07e65 wifi: mt76: mt7921: move mt792x_hw_dev in mt792x.h 4b49d659acab wifi: mt76: mt7921: Replace fake flex-arrays with flexible-array members 93f821cce8f5 wifi: mt76: mt792x: introduce mt792x-lib module de7b90721280 wifi: mt76: mt7921: move mac shared code in mt792x-lib module c68ee8a64bef wifi: mt76: mt7921: move dma shared code in mt792x-lib module 8d561811f271 wifi: mt76: mt7921: move debugfs shared code in mt792x-lib module 0034ae289046 wifi: mt76: mt7921: move init shared code in mt792x-lib module 8419c4e793a7 wifi: mt76: mt792x: introduce mt792x_irq_map b7c7fadf228c wifi: mt76: mt792x: move more dma shared code in mt792x_dma 0b1603ce707c wifi: mt76: mt7921: move hif_ops macro in mt792x.h e07540abe87a wifi: mt76: mt7921: move shared runtime-pm code on mt792x-lib 3d65cd7a8dad wifi: mt76: mt7921: move runtime-pm pci code in mt792x-lib 4551f8c838e6 wifi: mt76: mt7921: move acpi_sar code in mt792x-lib module bd84b8ebaff8 wifi: mt76: mt792x: introduce mt792x-usb module 7067ea0f1bab wifi: mt76: mt792x: move mt7921_load_firmware in mt792x-lib module cf752af84c35 wifi: mt76: mt76_connac3: move lmac queue enumeration in mt76_connac3_mac.h 700041dcf773 wifi: mt76: mt792x: move MT7921_PM_TIMEOUT and MT7921_HW_SCAN_TIMEOUT in common code 58b2b90ad89b wifi: mt76: mt7921: move mt7921_dma_init in pci.c 9e4cb87a04cf wifi: mt76: mt7921: move mt7921u_disconnect mt792x-lib c19b62fe6b68 wifi: mt76: testmode: add nla_policy for MT76_TM_ATTR_TX_LENGTH 4904ab2f87cd wifi: mt76: fix return value check in mt76x02_mac_process_rx 1f0fbbee359c wifi: mt76: mt7915: fix tlv length of mt7915_mcu_get_chan_mib_info 24a54ee3a5ec wifi: mt76: mt7915: fix power-limits while chan_switch 80b8bcf0e3ea wifi: mt76: mt7603: rework/fix rx pse hang check a8d9553d8fc4 wifi: mt76: mt7603: improve watchdog reset reliablity c03d84c0d018 wifi: mt76: mt7603: improve stuck beacon handling 85cc58378d25 wifi: mt76: mt7603: add missing register initialization for MT7628 b14c2351ddb8 wifi: mt76: mt7603: disable A-MSDU tx support on MT7628 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-mediatek: increase max. memory regions on mt7988-rfbDaniel Golle2023-08-24
| | | | | | | | | | | WED requires a bunch of additional reserved memory regions. As U-Boot's LMB allocator defaults to a maximum of only 8 regions, this currently makes using WED impossible. Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards with a SoC supporting WED. Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: fix bringing up AP+STA when the new channel is on a DFS channelFelix Fietkau2023-08-24
| | | | | | | If a CAC is needed because the channel is not available yet, a full AP interface restart is needed Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: in AP/STA, shut down AP interfaces when STA enters scanning stateFelix Fietkau2023-08-23
| | | | | | | | When the STA is brought up, it is set to DISABLED before adding the bss to ucode, so the first trigger to disable the AP is missed. Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: remove obsolete patchFelix Fietkau2023-08-23
| | | | | | It was only needed when hostapd was being started with one instance per PHY Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix MT7620 Wi-Fi channel scanning functionShiji Yang2023-08-22
| | | | | | | | | | | | During the channel scanning process, the driver will continuously switch channels. It seems that the full RF calibration step in rt2800_config_channel() caused the channel scanning function to timeout. To fix it, move the RF calibration to rt2800_enable_radio() so that it is only executed once. This commit also includes some coding format adjustments to follow the Linux recommended style. Fixes: 2824fa6963cf ("mac80211: rework MT7620 PA/LNA RF calibration") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* mediatek: filogic: wax220: cleanup device treeStefan Agner2023-08-22
| | | | | | | Fix compatible string to match what is supported upstream, fix alignment and order MTD partitions according to offset. Signed-off-by: Stefan Agner <stefan@agner.ch>
* hostapd: allow reduced neighbor report configurationDavid Bauer2023-08-22
| | | | | | | Reduced neighbor reports can be enabled by setting the "rnr" uci option to 1. Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-bcm53xx: Add U-Boot for NorthStar BCM53xxLinus Walleij2023-08-20
| | | | | | | | | | | | | | I recently added support for the NorthStar ARM BCM53xx SoCs to the upstream U-Boot. This is a back port on top of the 2023.04 version already imported to OpenWrt with the 5 necessary upstream patches. This is needed to create a small U-Boot for the BCM53xx-based D-Link DIR-890L and I think also the DIR-885L, so that a recent (bigger) kernel can be loaded and executed from the SEAMA partitions on these devices. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* filogic: support Telenor branded ZyXEL EX5700Bjørn Mork2023-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Telenor quirks -------------- The operator specific firmware running on the Telenor branded ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt installation. Notable changes to U-Boot include - environment is stored in RAM and reset to defaults when power cycled - dual partition scheme with "nomimal" or "rescue" systems, falling back to "rescue" unless the OS signals success in 3 attempts - several runtime additions to the device-tree Some of these modifications have side effects requiring workarounds - U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash unless this node exists - U-Boot verifies that the selected rootfs UBI volume exists, and refuses to boot if it doesn't. The chosen "rootfs" volume must contain a squashfs signature even for tftp or initramfs booting. - U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr" variable to the label mac. But "factoryparams" does not always exist. Instead there is a "RIP" volume containing all the factory data. Copying the "RIP" volume to "factoryparams" will fix this Hardware -------- SOC: MediaTek MT7986 RAM: 1GB DDR4 FLASH: 512MB SPI-NAND (Mikron xxx) WIFI: Mediatek MT7986 802.11ax 5 GHz Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz ETH: MediaTek MT7531 Switch + SoC 3 x builtin 1G phy (lan1, lan2, lan3) 2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan) USB: 1 x USB 3.2 Enhanced SuperSpeed port UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.2/24. Rename the image to C0A80101.img. 2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial console, Interrupt the autoboot process by pressing ESC when prompted. 3. Download and boot the OpenWrt initramfs image. $ env set uboot_bootcount 0 $ env set firmware nominal $ tftpboot $ bootm 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Missing features ---------------- - The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but OpenWrt does not correctly configure the output. - The "lan4" and "wan" port LEDs are driven by the GPH211C phys and not configured by OpenWrt. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: ubootenv-nvram: driver for RAM backed environmentsBjørn Mork2023-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The vendor U-Boot implementaion on Telenor branded ZyXEL EX5700 devices does not store its environment on flash. It is instead kept in a memory region. This is persistent over reboots, but not over power cycling. The dual partition failsafe system used by the vendor U-Boot requires the OS to modify a variable in this memory environment. This driver allows the ordinary uboot-envtools to access a memory region like it was a partition on NOR flash. The specific vendor U-Boot adds a "no-map" /reserved-memory section and a top level /ubootenv node pointing to the memory environment. The driver uses this device specific fact to locate the region. The matching and probing code will likely have to be adjusted for any other devices to be supported. Example partial device tree: / { .. ubootenv { memory-region = <&uenv>; compatible = "ubootenv"; }; .. reserved-memory { .. uenv: ubootenv@7ffe8000 { no-map; reg = <0 0x7ffe8000 0 0x4000>; }; Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq807x: add support for Netgear RAX120v2Thomas Kupper2023-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
* rtl8812au-ct: bump to fix kernel 6.1 compileJohn Thomson2023-08-19
| | | | | | | | | | | | | | | | | | | | | | 9b2b203 fix usb_recv_tasklet -Wcast-function-type a027da5 fix kernel 6.1 80211 link_id 7a9c802 fix build for kernel 6.1 prandom 3a3eb24 fix build for kernel 5.17 PDE_DATA fe2afbd fix build for kernel 5.17 const netdev->dev_addr 7275bae fix build for 5.17 kernel complete_and_exit c9c2aa7 Update usb_intf.c revert the upstream 6.1 link_id (depend on kernel version) changes and force 6.1 link_id The downstream patch casting const off the direct dev_addr writes triggers the runtime check from Linux d07b26f5bbea ("dev_addr: add a modification check") Fixes: #13261 Fixes: a07566ead82a ("rtl8812au-ct: fix even more compilation error with kernel 6.1") Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* packages: nvram: add asus,rt-ac3100 to set_wireless_led_behaviour quirkArınç ÜNAL2023-08-19
| | | | | | Add ASUS RT-AC3100 to the set wireless LED behaviour quirk. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* hostapd: revert upstream commit to fix #13156Stijn Tintel2023-08-18
| | | | | | | | | | | | Commit e978072baaca ("Do prune_association only after the STA is authorized") causes issues when an STA roams from one interface to another interface on the same PHY. The mt7915 driver is not able to handle this properly. While the commits fixes a DoS, there are other devices and drivers with the same limitation, so revert to the orginal behavior for now, until we have a better solution in place. Fixes: #13156 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* hostapd: fix bringing up mesh without supplicant when mcast rate is specifiedFelix Fietkau2023-08-17
| | | | | | The iw command expects a specific command line argument Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: update to the latest versionFelix Fietkau2023-08-17
| | | | | | 4711f74479e2 netifd: fix disabling radio via config if reconf is being used Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: netsupport: kmod-sched: Add act_skbmodHauke Mehrtens2023-08-15
| | | | | | | This adds act_skbmod.ko to kmod-sched. Fixes: #13224 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uboot-envtools: update to 2023.07.02Stefan Kalscheuer2023-08-15
| | | | | | | | | | | | Update to the latest stable version. This update changes the default lockfile directory from /var/lock to /run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might not even exist, so we add a patch to revert this particular change. [1] https://source.denx.de/u-boot/u-boot/-/commit/aeb40f1166e072856f865d26d42a4bea1ec3a514 Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* uboot-envtools: add u-boot env config for Xiaomi mi-miniIvan Pavlov2023-08-14
| | | | | | Add u-boot env config for Xiaomi mi-mini for using fw_printenv and fw_setenv on this board Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
* linux-firmware: Update Intel AX200 and AX210 firmwareHauke Mehrtens2023-08-14
| | | | | | | | | This updates the Intel iwlwifi firmware for AX200 and AX210 from version 66 to version 72. Version 72 is the latest version supported by iwlwifi from kernel 6.1. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Robert Marko <robimarko@gmail.com>
* uboot-mediatek: bpi-r3: prepare for larger FIT structuresDaniel Golle2023-08-13
| | | | | | | | | Instead of reading only a single 4kiB page, read the first 128kiB to determine the size of an uImage.FIT using 'imsz' or 'imszb'. This will be needed once we add more Device Tree Overlays, which may happen for the BPi-R3 mini. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-tools: fix build on macOS/DarwinFelix Fietkau2023-08-12
| | | | | | Resolve conflicts with the uuid type from darwin system headers Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: do not store data in object prototypeFelix Fietkau2023-08-12
| | | | | | | It cannot be properly cloned, since it is attached to the resource type. Use a separate registry for data. Fixes object confusion issues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: restart wifi when the bssid of the first interface changesFelix Fietkau2023-08-11
| | | | | | Full restart is necessary, since the bss wdev is not re-created Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: shut down client mode on the same phy while restarting APFelix Fietkau2023-08-11
| | | | | | | An active client mode interface could prevent the AP from claiming its channel and mess up the bringup sequence order Signed-off-by: Felix Fietkau <nbd@nbd.name>
* sunxi: add support for Banana Pi M3Zoltan HERPAI2023-08-11
| | | | | | | | | | | | | | CPU Allwinner A83t Octa-core Cortex A7 @ 1.2GHz Memory 2Gb DDR3 Storage SDcard, SATA (via USB), 8GB eMMC Network 10/100/1000M ethernet, Ampak AP6212 wifi + BT USB 2x USB 2.0 Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Powered by cgit, Themed by Ted Yin.