aboutsummaryrefslogtreecommitdiff
path: root/package/boot
Commit message (Collapse)AuthorAge
...
* uboot-envtools: replace use of platform_get_bootdevDaniel Golle2024-02-26
| | | | | | Use new function fitblk_get_bootdev in /lib/upgrade/common.sh instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: phase out uImage.FIT partition parserDaniel Golle2024-02-24
| | | | | | | | Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623. Introduce boot device selection for fitblk's /chosen/rootdisk handle, similar to how it is already done on MT7622, MT7986 and MT7988. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: fix truncated patchDaniel Golle2024-02-24
| | | | | | | | | | The default environment for the Linksys E8450 and Belkin RT3200 got truncated by one line due to a broken patch. While the impact was luckily only cosmetic, fix it so bootmenu title also shows U-Boot version again. Fixes: 6aec3c7b5b ("mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: Add support Netgear LBR20Marcin Gajda2024-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem. SoC Type: Qualcomm IPQ4019 RAM: 512 MiB Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC) Bootloader: U-Boot Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink WiFi class AC2200: - radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels - radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz - radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on. Ethernet: 2x1GbE (WAN/LAN1, LAN2) LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white USB ports: No Buttons: 2 Reset and SYNC(WPS) Power: 12 VDC, 2,5 A Connector type: Barrel OpenWRT Installation 1. Simplest way is just do upgrade from webpage with *factory.img 2. You can also do it with standard tool for Netgear's debricking - NMPRFlash 3. Most advanced way is to open device , connect to UART console and : - Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10) - Connect serial console (115200,8n1) to UART connector - Connect TFTP server to RJ-45 port - Stop in u-Boot and run u-Boot command: > setenv serverip 192.168.1.10 > set fdt_high 0x85000000 > tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb > bootm 0x83000000 - Login via ssh - upload or download *sysupgrade.bin ( like wget ... or scp transfer) - Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”) Back to Stock - Download firmware from official Netgear's webpage , it will be *.img file after decompressing. - Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash ) Open the case - Unscrew nuts and remove washers from antenna's conectors. - There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it - Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that. - PCB is screwed with 4Pcs of Torx T10 screws - Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires) - On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg ) BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org. Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* qualcommax: ipq807x: add support for Linksys MX5300Paweł Owoc2024-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: ======== SoC: Qualcomm IPQ8072A Flash: 512MB (Winbond W29N04GZBIBA) RAM: 1GB (2x Nanya DDR3L NT5CC256M16ER-EK) Ethernet: 5x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ac 4x4 (Qualcomm QCA9984 + Skyworks SKY85746-11) - channels 100-169 WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11) IoT: Bluetooth 5, Zigbee and Thread (Qualcomm QCA4024 + Skyworks SE2433T-R) IoT Flash: 4MB (Macronix MX25R3235F) RTC: ST M41T00S LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin image. More details can be found here: https://www.linksys.com/hk/support-article?articleNum=274497 After first boot check actual partition: - fw_printenv -n boot_part and install firmware on second partition using command in case of 2: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and in case of 1: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 2. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd21 0 0 nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd23 0 0 nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 3. Installation from initramfs image using USB FAT32 formatted drive: Stop u-boot and run: - usb start && fatload usb 0:1 $loadaddr openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 4. Back to the OEM firmware: - mtd -e kernel -n write FW_MX5300_1.1.9.200251_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MX5300_1.1.9.200251_prod.img alt_kernel 5. USB recovery: - fw_setenv usbimage 'openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb' fw_setenv bootusb 'usb start && fatload usb 0:1 $loadaddr $usbimage && bootm $loadaddr' fw_setenv bootcmd 'run bootusb; aq_load_fw && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' Notes: ======== IoT device is accesible over spi. Not yet supported. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq60xx: Add 8devices Mango DVKMantas Pucka2024-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com>
* uboot-rockchip: add Radxa CM3 IO board supportMarius Durbaca2024-02-21
| | | | | | | Add support for the Radxa CM3 IO board. Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org> Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
* rkbin: add rk3566 atf/tpl blobsMarius Durbaca2024-02-21
| | | | | | | Currently there are no atf/tpl blobs for rk3566 SoCs so this commit adds the prebuilt firmware from the vendor. Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
* rockchip: add NanoPi R4S Enterprise Edition buildTianling Shen2024-02-19
| | | | | | | | | | | FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address) to "enterprise" edition, and it was added as a "new" board in upstream kernel. This patch switched to use that upstreamed dts and removed local EEPROM patch. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: add NanoPi R2C Plus supportTianling Shen2024-02-19
| | | | | | Add support for the FriendlyARM NanoPi R2C Plus. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: bpi-r3-mini: fix typo in bootmenuDaniel Golle2024-02-16
| | | | | | | Fix typo in eMMC bootmenu. Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: fix NAND flash layoutDaniel Golle2024-02-16
| | | | | | | | Fix NAND flash layout which was out-of-sync with the definition in ARM TrustedFirmware-A which expects UBI to start at 0x200000. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: add BananaPi BPi-R3 miniDaniel Golle2024-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- SoC: MediaTek MT7986A 4x A53 Flash: 128MB SPI-NAND, 8GB eMMC RAM: 2GB DDR4 Ethernet: 2x 2.5GbE (Airoha EN8811H) WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G Interfaces: * M.2 Key-M: PCIe 2.0 x2 for NVMe SSD * M.2 Key-B: USB 3.0 with SIM slot * front USB 2.0 port LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD Button: Reset, internal boot switch Fan: PWM-controlled 5V fan Power: 12V Type-C PD Installation instructions for eMMC ---------------------------------- 0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt running there). 1. Write GPT partition table to eMMC Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to the device /tmp using scp and write it to /dev/mmcblk0: dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0 2. Reboot (to reload partition table) 3. Write bootloader and OpenWrt images Move files to the device /tmp using scp: - openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin - openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip - openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb - openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb Write them to the appropriate partitions: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0 dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3 dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4 dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5 sync 4. Remove the device from power, set boot switch to eMMC and boot into OpenWrt. The device will come up with IP 192.168.1.1 and assume the Ethernet port closer to the USB-C power connector as LAN port. 5. If you like to have Ethernet support inside U-Boot (eg. to boot via TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1: echo 0 > /sys/block/mmcblk0boot1/force_ro dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1 dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1 Installation instructions for NAND ---------------------------------- 0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there by instructions above. Using stock rom or immortalwrt does NOT work!) 1. Write things to NAND Move files to the device /tmp using scp: - openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin - openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip - openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb - openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb Write them to the appropriate locations: mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0 ubidetach -m 1 ubiformat /dev/mtd1 ubiattach -m 1 volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip) ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip cd /lib/firmware/airoha cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976 ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976 volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb) ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb) ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb 3. Remove the device from power, set boot switch to NAND, power up and boot into OpenWrt. Partially based on immortalwrt support for the R3 mini, big thanks for doing the ground work! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add builds for BananaPi BPi-R3 miniDaniel Golle2024-02-15
| | | | | | | | The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet. The driver added to U-Boot expects the firmware for the PHY to be stored inside UBI volume en8811h-fw or MMC boot1 hardware partition. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI buildDaniel Golle2024-02-15
| | | | | | | | | | | | | | | | | Move fip and factory into UBI static volumes. Use fitblk instead of partition parser. !! RUN INSTALLER FIRST !! Existing users of previous OpenWrt releases or snapshot builds will have to **re-run the updated installer** before upgrading to firmware after this commit. DO NOT flash or run even just the initramfs image unless you have run the updated installer which moves the content of the 'factory' partition into a UBI volume. tl;dr: DON'T USE YET! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblkDaniel Golle2024-02-15
| | | | | | No bootloader changes needed in this case, smooth transition. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblkDaniel Golle2024-02-15
| | | | | | | Modernize bootloader and flash memory layout of the BPi-R64 similar to how it has also been done for the BPi-R3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: add UBI-enabled builds for MT7622Daniel Golle2024-02-15
| | | | | | | Use custom UBI start address 0x80000 on MT7622 which is more than enough for a single bl2 (MT7622 BootROM doesn't support redundant bl2). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: mediatek_filogic: update bpi-r3Daniel Golle2024-02-15
| | | | | | Unify env configuration now that BPi-R4 and BPi-R3 both use fitblk. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: bpi-r3: all-UBI NAND layout, use fitblkDaniel Golle2024-02-15
| | | | | | | | | | Modernize U-Boot to provide a better reference: * store fip image in UBI now that TF-A supports that * switch from uImage.FIT partition parser to new fitblk virtual firmware block driver (root=/dev/fit0) * automatically set root device according to boot_mode register Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: add mt7986-spim-nand-ubi-ddr4Daniel Golle2024-02-15
| | | | | | | Add UBI-enabled build for MT7986 with SPIM-NAND and DDR4 for use with the BananaPi R3 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: filogic: add support for BananaPi R4Daniel Golle2024-02-15
| | | | | | | | Add environment settings for the BananaPi BPI-R4 router board which can boot from (and store its bootloader environment on) micro SD card, SPI-NAND and eMMC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: filogic: de-duplicate UBI env settingsDaniel Golle2024-02-15
| | | | | | | Use function instead of duplicating the env settings on UBI for OpenWrt-built U-Boot over and over. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: update to U-Boot 2024.01 releaseDaniel Golle2024-02-15
| | | | | | | | Rebase local patches on top of quarterly timed release, allowing to drop numerous patches which have been accepted upstream since the release of U-Boot 2023.07.02. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add build for BPi-R4Daniel Golle2024-02-15
| | | | | | | Add build for the BananaPi R4 board which can boot from micro SD, SPI-NAND or eMMC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: mt7988: set rootdisk according to boot deviceDaniel Golle2024-02-15
| | | | | | | If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk phandle according to boot device selected by the bootstrap pins. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: fix MMC erase timeoutDaniel Golle2024-02-15
| | | | | | | | When erasing large amounts of blocks at once this can take a long time on slow cards. Instead of a fixed timeout, wait longer if more blocks are being erased. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)Daniel Golle2024-02-15
| | | | | | | | | Add basic U-Boot drop-in replacement compatible with the flash layout of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board. The idea here is a to have a reference build of uboot-mediatek also for a simple MIPS boards more popular than MT7621 RFB. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: use UBI on new NAND targetsDaniel Golle2024-02-15
| | | | | | | | | | Make use of recently added UBI support in MediaTek's ARM TrustedFirmware-A on new MT7988 SoC. Load fip from static UBI volume instead of fixed offset on SPIM-NAND and SNFI. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: set HIDDEN=yDaniel Golle2024-02-15
| | | | | | | | Hide arm-trusted-firmware-mediatek packages from interactive config. Exposing them only causes confusion and needed variants are anyway selected as dependencies by uboot-mediatek packages. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: backport some usefull patches from v2024.04-rc1Shiji Yang2024-02-11
| | | | | | | | Highlights: - Silence small page read warning. - Autodetect NAND erase size and env sectors. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* uboot-envtools: update to 2024.01Nick Hainke2024-02-09
| | | | | | | | | Update to latest version. Refresh patches: - 002-Revert-tools-env-use-run-to-store-lockfile.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* kexec-tools: update to 2.0.28Nick Hainke2024-02-06
| | | | | | | | Release Notes: - https://www.spinics.net/lists/kexec/msg32139.html - https://www.spinics.net/lists/kexec/msg33447.html Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: add Comfast CF-E393AX supportDavid Bentham2024-02-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point. Oem firmware is a custom openwrt 21.02 snapshot version. We can gain access via ssh once we remove the root password. Hardware specification: SoC: MediaTek MT7981A 2x A53 Flash: 128 MB SPI-NAND RAM: 256MB DDR3 Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN) 1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN) Switch: MediaTek MT7531AE WiFi: MediaTek MT7976D LEDS: 1x (Red, Blue and Green) Button: Reset UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | VCC GND TX RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface (http://apipaddress/computer/login.html), and download the configuration(http://apipaddress/computer/config.html). 2. Rename downloaded backup config - 'backup.file to backup.tar.gz', Enter 'fakeroot' command then decompress the configuration: tar -zxf backup.tar.gz 3. Edit 'etc/shadow', update (remove) root password: With password = 'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::' 'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::' to Without password = 'root::0:99999:7:::' 'root::0:99999:7:::' 4. Repack 'etc' directory back to a new backup file: tar -zcf backup-ssh.tar.gz etc/ 5. Rename new config tar.gz file to 'backup-ssh.file' Exit fakeroot - 'exit' 6. Upload new configuration via web interface, now you can SSH with the following: 'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \ -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'. Backup the mtd partitions - https://openwrt.org/docs/guide-user/installation/generic.backup 7. Copy openwrt factory firmware to the tmp folder to install via ssh: 'scp -o HostKeyAlgorithms=+ssh-rsa \ -o PubkeyAcceptedAlgorithms=+ssh-rsa \ *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \ root@192.168.10.1:/tmp/' 'sysupgrade -n -F \ /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin' 8. Once led has stopped flashing - Connect via ssh with the default openwrt ip address - 'ssh root@192.168.1.1' 9. SSH copy the openwrt sysupgrade firmware and upgrade as per the default instructions. Signed-off-by: David Bentham <db260179@gmail.com>
* mediatek: drop NMBM layout for Xiaomi WR30UChuanhong Guo2024-01-23
| | | | | | | | | This reverts commit dcdcfc15115a1038e90f21f5aa41726d9c7e2fe5. This is a firmware for third-party u-boot mod, which should not be carried here by us. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* uboot-rockchip: Update to 2024.01Tianling Shen2024-01-20
| | | | | | | | | | | | | | Runtime tested on Orange Pi R1 Plus LTS and NanoPi R4S. Removed upstreamed patches: - 100-rockchip-rk3328-Add-support-for-Orange-Pi-R1-Plus.patch - 101-rockchip-rk3328-Add-support-for-Orange-Pi-R1-Plus-LT.patch - 103-rockchip-rk3568-Add-support-for-FriendlyARM-NanoPi-R.patch - 104-rockchip-rk3568-Add-support-for-FriendlyARM-NanoPi-R.patch Refreshed remaining patches. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* arm-trusted-firmware-rockchip: Update to 2.10Tianling Shen2024-01-20
| | | | | | | | Runtime tested on Orange Pi R1 Plus LTS (RK3328) and NanoPi R4S (RK3399). Changelog: https://trustedfirmware-a.readthedocs.io/en/v2.10/change-log.html Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-bcm53xx: bump to 2024.01Linus Walleij2024-01-20
| | | | | | | | Bump the U-Boot version used for BCM53xx to the 2024.01 version that includes all the needed patches upstream, so we can get rid of those in the process. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* mediatek: add support for JDCloud RE-CP-03Tianling Shen2024-01-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: 128GB eMMC RAM: 1GB DDR4 Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B) Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Joylink Power: DC 12V 2A Flash instructions: 1. Download and flash the vendor migration firmware via webUI: https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin (Default address is 192.168.68.1, user root, no password) 2. After device has booted up, write new GPT table: dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync 3. Erase and write new BL2: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync 4. Erase and write new FIP: dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync 5. Set static IP on your PC: IP 192.168.1.254/24, GW 192.168.1.1 6. Serve OpenWrt initramfs image using TFTP server. 7. Cut off the power and re-engage, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. 9. Additionally, if you want to have eMMC recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: add support for JDCloud RE-CP-03Tianling Shen2024-01-19
| | | | | | | The vendor U-Boot has enabled signature verification, so add a custom U-Boot build for OpenWrt. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: add support for Xiaomi AX3000TDim Fish2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **SoC**: MediaTek MT7981B 2x A53 **Flash**: ESMT F50L1G41LB 128MB **RAM**: NT52B128M16JR-FL 256MB **Ethernet**: 4x 10/100/1000 Mbps **Switch**: MediaTek MT7531AE **WiFi**: MediaTek MT7976C **Buttons**: Reset, Mesh **Power**: DC 12V 1A 1. Get ssh access. Supported stock firmware **1.0.47** ``` curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A ``` 2. Backup stock partitions ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then transfer them to your computer in a safe place. 3. Get firmware information `cat /proc/cmdline` 4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash If **firmware=0** ``` ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` If **firmware=1** ``` ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` Then reboot your router, it should boot to the OpenWrt initramfs system now. 5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin` 1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` `reboot` 2. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 3. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 4. *(Optional **-10Mb** free space) Add recovery boot feature.* ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb ``` 5. Flash Openwrt U-Boot ``` mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2 mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP ``` 6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb` 1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock images from backup ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Signed-off-by: Dim Fish <dimfish@gmail.com>
* ipq807x: add support for Linksys MX4200 V1 and V2Mohammad Sayful Islam2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys MX4200 is a 802.11ax Tri-band router/AP. Specifications: * CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 512Mb NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * RGB system led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition fw_printenv -n boot_part - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel Replace (X) with your model version either 1 or 2 Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* mediatek: Add support for D-Link EAGLE PRO AI R32Roland Reinl2024-01-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | R32 is like the M32 part of the EAGLE PRO AI series from D-Link. Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 2 LEDs (Status and Internet, both can be either orange or white) - 2 buttons (WPS and Reset) Compared to M32, the R32 has the following differences: - 4 LAN ports instead of 2 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001 - Individual LEDs for power and internet - MAC address is stored at another offset in the ODM partition MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x81 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment. The support for the M32/R32 already includes support for flashing from the OEM web interface: - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap) Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* mediatek: filogic: add support ASUS RT-AX59UXavier Franquet2023-12-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (based on support for ASUS RT-AX59U by liushiyou006) SOC: MediaTek MT7986 RAM: 512MB DDR4 FLASH: 128MB SPI-NAND (Winbond W25N01GV) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: MediaTek MT7531 Switch UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Upgrade from AsusWRT to OpenWRT using UART Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin. Connect the PC with TFTP server to the RT-AX59U. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0) Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.70 $ tftpboot 0x46000000 rtax59u.bin $ bootm 0x46000000 Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Upgrade from AsusWRT to OpenWRT using WebUI Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file Wait for OpenWRT to boot (192.168.1.1). Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT. We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g when bit 28 is already set. : Stock : OpenWrt WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4 WLAN 2g (2) : : CA:xx:xx:0D:xx:D4 WLAN 2g (3) : : CE:xx:xx:0D:xx:D4 WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5 WLAN 5g (2) : : CE:xx:xx:1D:xx:D5 WLAN 5g (3) : : C2:xx:xx:1D:xx:D5 WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE WLAN 2g (2) : : 0A:xx:xx:76:xx:BE WLAN 2g (3) : : 0E:xx:xx:76:xx:BE WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF WLAN 5g (2) : : 0E:xx:xx:76:xx:BF WLAN 5g (3) : : 02:xx:xx:76:xx:BF Signed-off-by: Xavier Franquet <xavier@franquet.es>
* mediatek: add support for Routerich AX3000Mikhail Zhilkin2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR is continuation of work under "mediatek: add support for Routerich AX3000" #13703 by the agreement with PR #13703 original author (Maximilian Weinmann <x1@disroot.org>). All reviews from the previous PR were taken into into account. Routerich AX3000 is a wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 256 MiB (ESMT M15T2G16128A) - Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MIMO 2x2 - 5 GHz : a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE) - USB : 1x 2.0 - UART : through-hole on PCB - [J500] GND, TX, RX, 3.3V (115200n8) - Buttons : Mesh, Reset - LEDs : 1x Power (Blue) 1x WiFi 2.4 GHz (Blue) 1x WiFi 5 GHz (Red) 1x Mesh (Blue) 3x LAN activity (Blue) 1x WAN activity (Blue) 2x WAN no-internet (Red) - Power : 12 VDC, 1.5 A Installation ------------ Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface (without keeping settings). Return to stock --------------- Install stock firmware image (without keeping settings) using OpenWrt sysupgrade method. Recovery -------- Connect uart, use u-boot menu to flash stock firmware image or boot OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:b4 | label | | LAN | 24:0f:5e:xx:xx:b5 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* mediatek: add support for Zbtlink ZBT-Z8103AXIan Oderon2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND No. of Antennas: 6 Note: Upon opening the router, only 5 antennas were connected to the mainboard. Led Layout: Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi Buttons: Reset-Mesh Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Signed-off-by: Ian Oderon <ianoderon@gmail.com>
* arm-trusted-firmware-sunxi: Update to 2.10Tianling Shen2023-12-20
| | | | | | | | Runtime tested on NanoPi R1S H5 and Orange Pi Zero3. Changelog: https://trustedfirmware-a.readthedocs.io/en/v2.10/change-log.html Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-envtools: bump PKG_RELEASERafał Miłecki2023-12-13
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* uboot-envtools: fix reading NVMEM device's compatible valueRafał Miłecki2023-12-13
| | | | | Fixes: fea4ffdef28f ("uboot-envtools: update to 2023.04") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for Rostelecom RT-FE-1AMikhail Zhilkin2023-12-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: No Button: 2 buttons (Reset & WPS) LEDs: - 1x Power (green, unmanaged) - 1x Status (green, gpio) - 1x 2.4G (green, hardware, mt76-phy0) - 1x 2.4G (blue, gpio) - 1x 5G (green, hardware, mt76-phy1) - 1x 5G (blue, gpio) - 5x Ethernet (green, hardware, 4x LAN & WAN) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (default http://192.168.0.1/) under "admin" account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following block: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" /> </OBJECT> 5. Replace <some value> by a new superadmin password and add a line which enabling superadmin login after. For example, the block after the changes: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" /> <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> </OBJECT> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (superadmin:xxxxxxxxxx, where xxxxxxxxxx is a new password from the p.5) 9. Enable SSH access to the router (Settings -> Access control -> SSH) 10. Connect to the router using SSH shell using superadmin account 11. Run in SSH shell: sh 12. Make a mtd backup (optional, see related section) 13. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 14. Login to the router web interface under admin account 15. Remove dots from the OpenWrt factory image filename 16. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 192.168.0.2 MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | f4:*:66 | | WAN | label + 11 | f4:*:71 | | 2g | label + 2 | f4:*:68 | | 5g | label + 3 | f4:*:69 | +-----+------------+---------+ The label MAC address was found in Factory, 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Powered by cgit, Themed by Ted Yin.