aboutsummaryrefslogtreecommitdiff
path: root/package/boot
Commit message (Collapse)AuthorAge
...
* uboot-mediatek: add support for JDCloud RE-CP-03Tianling Shen2024-01-19
| | | | | | | The vendor U-Boot has enabled signature verification, so add a custom U-Boot build for OpenWrt. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: add support for Xiaomi AX3000TDim Fish2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **SoC**: MediaTek MT7981B 2x A53 **Flash**: ESMT F50L1G41LB 128MB **RAM**: NT52B128M16JR-FL 256MB **Ethernet**: 4x 10/100/1000 Mbps **Switch**: MediaTek MT7531AE **WiFi**: MediaTek MT7976C **Buttons**: Reset, Mesh **Power**: DC 12V 1A 1. Get ssh access. Supported stock firmware **1.0.47** ``` curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A ``` 2. Backup stock partitions ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then transfer them to your computer in a safe place. 3. Get firmware information `cat /proc/cmdline` 4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash If **firmware=0** ``` ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` If **firmware=1** ``` ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` Then reboot your router, it should boot to the OpenWrt initramfs system now. 5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin` 1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` `reboot` 2. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 3. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 4. *(Optional **-10Mb** free space) Add recovery boot feature.* ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb ``` 5. Flash Openwrt U-Boot ``` mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2 mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP ``` 6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb` 1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock images from backup ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Signed-off-by: Dim Fish <dimfish@gmail.com>
* ipq807x: add support for Linksys MX4200 V1 and V2Mohammad Sayful Islam2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys MX4200 is a 802.11ax Tri-band router/AP. Specifications: * CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 512Mb NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * RGB system led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition fw_printenv -n boot_part - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel Replace (X) with your model version either 1 or 2 Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* mediatek: Add support for D-Link EAGLE PRO AI R32Roland Reinl2024-01-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | R32 is like the M32 part of the EAGLE PRO AI series from D-Link. Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 2 LEDs (Status and Internet, both can be either orange or white) - 2 buttons (WPS and Reset) Compared to M32, the R32 has the following differences: - 4 LAN ports instead of 2 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001 - Individual LEDs for power and internet - MAC address is stored at another offset in the ODM partition MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x81 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment. The support for the M32/R32 already includes support for flashing from the OEM web interface: - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap) Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* mediatek: filogic: add support ASUS RT-AX59UXavier Franquet2023-12-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (based on support for ASUS RT-AX59U by liushiyou006) SOC: MediaTek MT7986 RAM: 512MB DDR4 FLASH: 128MB SPI-NAND (Winbond W25N01GV) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: MediaTek MT7531 Switch UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Upgrade from AsusWRT to OpenWRT using UART Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin. Connect the PC with TFTP server to the RT-AX59U. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0) Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.70 $ tftpboot 0x46000000 rtax59u.bin $ bootm 0x46000000 Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Upgrade from AsusWRT to OpenWRT using WebUI Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file Wait for OpenWRT to boot (192.168.1.1). Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT. We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g when bit 28 is already set. : Stock : OpenWrt WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4 WLAN 2g (2) : : CA:xx:xx:0D:xx:D4 WLAN 2g (3) : : CE:xx:xx:0D:xx:D4 WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5 WLAN 5g (2) : : CE:xx:xx:1D:xx:D5 WLAN 5g (3) : : C2:xx:xx:1D:xx:D5 WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE WLAN 2g (2) : : 0A:xx:xx:76:xx:BE WLAN 2g (3) : : 0E:xx:xx:76:xx:BE WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF WLAN 5g (2) : : 0E:xx:xx:76:xx:BF WLAN 5g (3) : : 02:xx:xx:76:xx:BF Signed-off-by: Xavier Franquet <xavier@franquet.es>
* mediatek: add support for Routerich AX3000Mikhail Zhilkin2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR is continuation of work under "mediatek: add support for Routerich AX3000" #13703 by the agreement with PR #13703 original author (Maximilian Weinmann <x1@disroot.org>). All reviews from the previous PR were taken into into account. Routerich AX3000 is a wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 256 MiB (ESMT M15T2G16128A) - Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MIMO 2x2 - 5 GHz : a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE) - USB : 1x 2.0 - UART : through-hole on PCB - [J500] GND, TX, RX, 3.3V (115200n8) - Buttons : Mesh, Reset - LEDs : 1x Power (Blue) 1x WiFi 2.4 GHz (Blue) 1x WiFi 5 GHz (Red) 1x Mesh (Blue) 3x LAN activity (Blue) 1x WAN activity (Blue) 2x WAN no-internet (Red) - Power : 12 VDC, 1.5 A Installation ------------ Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface (without keeping settings). Return to stock --------------- Install stock firmware image (without keeping settings) using OpenWrt sysupgrade method. Recovery -------- Connect uart, use u-boot menu to flash stock firmware image or boot OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:b4 | label | | LAN | 24:0f:5e:xx:xx:b5 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* mediatek: add support for Zbtlink ZBT-Z8103AXIan Oderon2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND No. of Antennas: 6 Note: Upon opening the router, only 5 antennas were connected to the mainboard. Led Layout: Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi Buttons: Reset-Mesh Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Signed-off-by: Ian Oderon <ianoderon@gmail.com>
* arm-trusted-firmware-sunxi: Update to 2.10Tianling Shen2023-12-20
| | | | | | | | Runtime tested on NanoPi R1S H5 and Orange Pi Zero3. Changelog: https://trustedfirmware-a.readthedocs.io/en/v2.10/change-log.html Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-envtools: bump PKG_RELEASERafał Miłecki2023-12-13
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* uboot-envtools: fix reading NVMEM device's compatible valueRafał Miłecki2023-12-13
| | | | | Fixes: fea4ffdef28f ("uboot-envtools: update to 2023.04") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for Rostelecom RT-FE-1AMikhail Zhilkin2023-12-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: No Button: 2 buttons (Reset & WPS) LEDs: - 1x Power (green, unmanaged) - 1x Status (green, gpio) - 1x 2.4G (green, hardware, mt76-phy0) - 1x 2.4G (blue, gpio) - 1x 5G (green, hardware, mt76-phy1) - 1x 5G (blue, gpio) - 5x Ethernet (green, hardware, 4x LAN & WAN) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (default http://192.168.0.1/) under "admin" account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following block: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" /> </OBJECT> 5. Replace <some value> by a new superadmin password and add a line which enabling superadmin login after. For example, the block after the changes: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" /> <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> </OBJECT> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (superadmin:xxxxxxxxxx, where xxxxxxxxxx is a new password from the p.5) 9. Enable SSH access to the router (Settings -> Access control -> SSH) 10. Connect to the router using SSH shell using superadmin account 11. Run in SSH shell: sh 12. Make a mtd backup (optional, see related section) 13. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 14. Login to the router web interface under admin account 15. Remove dots from the OpenWrt factory image filename 16. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 192.168.0.2 MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | f4:*:66 | | WAN | label + 11 | f4:*:71 | | 2g | label + 2 | f4:*:68 | | 5g | label + 3 | f4:*:69 | +-----+------------+---------+ The label MAC address was found in Factory, 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* uboot-envtools: fix GL-MT2500 offsetDavid Bauer2023-12-03
| | | | | | | | The previous offsets did also work, as they've wrapped back to 0x0. However, in reality the environment starts at offset 0x0 of the u-boot-env MMC partition. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add support for GL.iNet GL-MT2500David Bauer2023-11-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7981BA RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR) MMC: 8GB eMMC (Samsung 8GTF4R) ETH: 1000Base-T LAN (ePHY) 2500Base-T WAN (MaxLinear GPY211C) BTN: 1x Reset Button LED: System (blue/white) VPN (white) USB: 1x USB-A (USB 3.0) UART: 115200 8N1 - Pinout on board next to LAN port Don't connect 3.3V! Known Issues ------------ U-Boot vendor recovery does not seem to accept any images, neither GL.iNet images nor OpenWrt images. Recovery requires serial access! Installation ------------ Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to not retain existing settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-rockchip: add NanoPi R5C supportTianling Shen2023-11-26
| | | | | | Add support for the FriendlyARM NanoPi R5C. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: add NanoPi R5S supportTianling Shen2023-11-26
| | | | | | | Add support for the FriendlyARM NanoPi R5S support. Tested-by: Packet Please <pktpls@systemli.org> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* rkbin: add new TF-A package for rk35xxTianling Shen2023-11-26
| | | | | | | Currently there's no usable mainline (open source) TF-A implementation for rk35xx SoCs, so pack the prebuilt firmware from the vendor. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: Update to 2023.07.02Tianling Shen2023-11-26
| | | | | | | | | | | | | | | * Removed swig hacks and prebuilt of-platdata * Removed upstreamed patches - 101-rock64pro-disable-CONFIG_USE_PREBOOT.patch - 102-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R2C.patch * Reordered patches * Introduced new dependencies check * Overrided default PATH to avoid race condition (host python3 vs hostpkg python3) * Switched to use UBOOT_CUSTOMIZE_CONFIG for config update Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-sunxi: use intree dtc explicitlyTianling Shen2023-11-26
| | | | | | This replaces pylibfdt hack. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-sifiveu: use intree dtc explicitlyTianling Shen2023-11-26
| | | | | | This replaces pylibfdt hack. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: use intree dtc explicitlyTianling Shen2023-11-26
| | | | | | This replaces pylibfdt hack. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: add support for D-link DAP-1720 A1Rani Hod2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa <protectivedad@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com>
* uboot-envtools: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* uboot-envtools: add support for Zyxel EX5601-T0 ubootmodNicolò Veronese2023-11-25
| | | | | | | | The ubootmod bootlaoder for EX5601-T0 uses two partitions in ubi to store enviroment variables. so proper config is needed. Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* uboot-mediatek: add initial Zyxel EX5601-T0 supportValerio 'ftp21' Mancini2023-11-25
| | | | | | | | | | | | | | | | | | | | | | | Flash procedure is described in next commit. TLDR: Copy preloader and uboot to /tmp and write them in the mtd. This will also require new UBI partition and volumes to boot openwrt. mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2 mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip Changelist: - Added profile for 4k+256 SPI NAND_TYPE - Added basic Zyxel EX5601-T0 uboot profile Backported from hitech95 branch: - Button RESET pin fix - Button WPS pin fix Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu> Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* mediatek: add support for Zbtlink ZBT-Z8102AXDaniel Golle2023-11-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 1024MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 4 LAN (Gigabit) USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by Ian Ishmael C. Oderon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add settings for Synology DS213jDaniel Golle2023-11-20
| | | | | | | Add settings to be able to access the U-Boot environment on the Synology DS213j NAS. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: Fix ubi command in uboot commandsCarter Wang2023-11-19
| | | | | | | Fix typo 'ubi remote ...' -> 'ubi remove ...'. Signed-off-by: Carter Wang <carter.wang@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add JCG Q30 PRO supportChukun Pan2023-11-19
| | | | | | | The vendor uboot will verify firmware at boot. So add a custom uboot build for this device. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* arm-trusted-firmware-mediatek: update to release 2023-10-13Daniel Golle2023-11-09
| | | | | | Drop local patches now upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add environment config for MeiG SLT866Daniel Golle2023-11-03
| | | | | | Add configuration to access U-Boot environment on MeiG SLT866. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "uboot-sunxi: add missing type __u64"Petr Štetiar2023-11-02
| | | | | | | | | This reverts commit 3cc57ba4627c9c7555f8ad86e4f78d86d8f9ddf0 as it should be fixed in commit 78cbd5a57e11 ("tools: macOS: types.h: fix missing unsigned types"). References: #13833 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "uboot-mediatek: fix build on Mac OS X"Petr Štetiar2023-11-02
| | | | | | | | | This reverts commit 997ff740dc44045390680eaa30b6566d40bca322. 78cbd5apick as it should be fixed in commit 78cbd5a57e11 ("tools: macOS: types.h: fix missing unsigned types"). References: #13833 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* uboot-mediatek: fix determine the size of an uImage.FIT using 'imsz' or 'imszb'.Jianhui Zhao2023-10-31
| | | | | | | It must read the entire image for previous code of 'imsz' or 'imszb'. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com> Suggested-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for GL.iNet GL-S200Weiping Yang2023-10-31
| | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9531(650MHz) RAM: DDR2 128M Flash: SPI NOR 16M + SPI NAND 128M WiFi: 2.4GHz with 2 antennas(WiFi/Thread) Ethernet: 1xLAN(10/100M) 2xWAN(10/100M) Button: 1x Reset Button Switch: 1x Mode switch LED: 1x Blue LED + 1x White LED + 1x Orange LED IOT: Thread + ZigBee/Zwave By uboot web failsafe: Push the reset button for 5 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ramips: add support for ZyXEL LTE5398-M904Milan Krstic2023-10-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS port. Specifications: * SoC: Mediatek MT7621AT * RAM: 256 MB * Flash: 128MB NAND (MX30LF1G18AC) * WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G * Switch: 2 GbE ports MT7530 * LTE/3G: Quectel EG18-EA LTE-A Cat. 18 * SIM: 1 micro-SIM card slot * Buttons: Reset, WPS * LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G) * VoIP: 1 FXS RJ11 port * Power: 12V, 2A UART serial console: 57600,8N1 Unpopulated header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Installation: * Log in as root using ssh to 192.168.1.1 * scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/ * Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit * Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot * Wait for OpenWrt to boot and ssh to root@192.168.1.1 * Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image For mode details about flashing see: 2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19) Unsupported: * FXS/Voice Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
* uboot-mediatek: Sync phy-mode for Xiaomi Redmi Router AX6000Furong Xu2023-10-28
| | | | | | | | | | | Commit 572ea6807053 ("uboot-mediatek: add patches for MT7988 and builds for RFB") renamed HSGMII to 2500basex, but forgot to update the dts of Redmi Router AX6000, makes the network unusable. This patch makes the network usable again. Fixes: #13724 Fixes: 572ea6807053 ("uboot-mediatek: add patches for MT7988 and builds for RFB") Signed-off-by: Furong Xu <xfr@outlook.com>
* qualcommax: ipq807x: add support for Netgear WAX630Kristian Skramstad2023-10-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz * RAM: 1 GiB of DDR3 466 MHz * Flash: NAND 512 MiB (Winbond W29N04GZ) * 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L * UART: One 4-pin populated header next to the heatsink and a chip. GND RXD TXD, beginning from the external antennas. 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at * One 100/1000 Gigabit Ethernet Wlan: * 4x4 in 2.4GHz : 802.11b/g/n/ax * 4x4 in 5.0GHz L: 802.11a/n/ac/ax * 4x4 in 5.0GHz H: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H) Power: * 802.3bt/at 30.1W * DC 12V/3.5A Mounting: Wall and ceiling ``` ``` 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to the console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* mediatek: add CMCC RAX3000M supportTianling Shen2023-10-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 64GB eMMC or 128 MB SPI-NAND RAM: 512MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A - UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | GND TX VCC RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface, and download the configuration. 2. Enter fakeroot, decompress the configuration: tar -zxf cfg_export_config_file.conf 3. Edit 'etc/config/dropbear', set 'enable' to '1'. 4. Edit 'etc/shadow', update (remove) root password: 'root::19523:0:99999:7:::' 5. Repack 'etc' directory: tar -zcf cfg_export_config_file.conf etc/ * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat', just ignore it. 6. Upload new configuration via web interface, now you can SSH to RAX3000M. Check stroage type: Check the label on the back of the device: "CH EC CMIIT ID: xxxx" is eMMC version "CH CMIIT ID: xxxx" is NAND version eMMC Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'factory' part. ('data' partition can be ignored, it's useless.) 2. Write new GPT table: dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync 3. Erase and write new BL2: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync 4. Erase and write new FIP: dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync 5. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 6. Serve OpenWrt initramfs image using TFTP server. 7. Cut off the power and re-engage, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. 9. Additionally, if you want to have eMMC recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync NAND Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'Factory' part. 2. Erase and write new BL2: mtd erase BL2 mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2 3. Erase and write new FIP: mtd erase FIP mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP 4. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 5. Serve OpenWrt initramfs image using TFTP server. 6. Cut off the power and re-engage, wait for TFTP recovery to complete. 7. After OpenWrt has booted, erase UBI volumes: ubidetach -p /dev/mtd0 ubiformat -y /dev/mtd0 ubiattach -p /dev/mtd0 8. Create new ubootenv volumes: ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB 9. Additionally, if you want to have NAND recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb 10. Perform sysupgrade. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: add support for CMCC RAX3000MTianling Shen2023-10-28
| | | | | | | The OEM U-Boot uses dual boot and signature verification which does not support by OpenWrt. So add a custom U-Boot build for OpenWrt. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* arm-trusted-firmware-mediatek: add emmc/spim-nand ddr4 build for mt7981Tianling Shen2023-10-28
| | | | | | They will be used on CMCC RAX3000M. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: fix global pll clock override on mtk_spimNicolò Veronese2023-10-22
| | | | | | | | | | | | With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch a new system to calculate the SPI clocks has been added. Unfortunately, the do_div macro overrides the global priv->pll_clk_rate field. This will cause to have a reduced clock rate on each subsequent SPI call. Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu> Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* uboot-mvebu: armada 388 clearfog: support additional ddr configurationsJosua Mayer2023-10-22
| | | | | | | | | Fixes Issue #13632. Patches as submitted in v1 to u-boot mailinglist: https://lists.denx.de/pipermail/u-boot/2023-October/533148.html Signed-off-by: Josua Mayer <josua@solid-run.com>
* uboot-mediatek: fix typo in bootmenu for GL-MT6000Jianhui Zhao2023-10-20
| | | | | | Fixes: fe10f97 ("filogic: add support for GL.iNet GL-MT6000") Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
* boot/apex: Restore the APEX boot loaderLinus Walleij2023-10-20
| | | | | | | | | | | | | | | | | | This is a partial revert of the deletion of the IXP4xx target: we restore the APEX boot loader so we can use it for the NSLU2 and related targets. The APEX upstream is as dead as it gets so I have applied OpenWrts old patches on top of the never released v1.6.10 version and forked it into an OpenWrt variant on GitHub. If the upstream comes back alive I will happily switch over to it. The file refers to the external GitHub, I suppose when integrating this patch the file should be copied to OpenWrts file repository and the file link changed. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ipq806x: add support for Extreme Networks AP3935Glen Lee2023-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee <g2lee@yahoo.com>
* filogic: add support for GL.iNet GL-MT6000Jianhui Zhao2023-09-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: * SoC: MediaTek MT7986A 4x A53 * Flash: 8GB EMMC * RAM: 1GB DDR4 * Ethernet: * 2x2.5G RJ45 port (RTL8221B) * 4x1G RJ45 ports (MT7531AE) * WLAN: * 2.4GHz: MT7976GN 4T4R * 5GHz: MT7976AN 4T4R * Button: Reset * LED: 1 x dual color LED * USB: 1 x USB 3.0 * Power: DC 12V 4A * UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC) * JTAG: 9 PIN If you want to use u-boot from OpenWrt, you can upgrade it safely. * bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin * fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip `openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
* uboot-mediatek: sync spi-nand driver with SDKChukun Pan2023-09-29
| | | | | | | | | | | When adding new router support, I found that uboot could not recognize flash: "unknown raw ID xxx". Sync SPI-NAND driver for mediatek to fixes this: * Add support for Winbond W25N01KV 1Gbit chip. * Add support for Etron SPI-NAND chip. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* treewide: Add extra CPE identifierHauke Mehrtens2023-09-25
| | | | | | | This adds some Common Platform Enumerations (CPE) identifiers which I found. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)Elbert Mai2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti U6+ is a dual-band WiFi 6 PoE access point. It is a drop-in upgrade of the U6 lite. Specifications --- - SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz - RAM: 256 MB DDR3-2133 RAM - Flash: 16 MB SPI NOR and 4 GB eMMC - LAN: 1x Gigabit Ethernet with 802.3af/at support - WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6 - LEDs: 1x blue and 1x white - Buttons: 1x reset button Installation --- 1. Power device using a PoE injector or switch 2. Connect via Ethernet to the device with static IP 192.168.1.2 3. SSH into the device with password: ubnt $ ssh ubnt@192.168.1.20 4. Unlock kernel partitions for writing $ echo 5edfacbf > /proc/ubnthal/.uf 5. Confirm correct partitions $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent PARTNAME=kernel0 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent PARTNAME=kernel1 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent PARTNAME=bs 6. Set and confirm bootloader environment $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd_real "run boot_openwrt" $ fw_printenv 7. Copy sysupgrade image to /tmp/openwrt.bin via scp 8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6 $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7 9. Ensure device boots from mmcblk0p6 $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8 10. Reboot the device $ reboot Signed-off-by: Elbert Mai <code@elbertmai.com> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* arm-trusted-firmware-sunxi: update to version 2.9Sebastian Pflieger2023-09-24
| | | | | | | | | - detect die revision used in variants of the Allwinner H616 SoC (H313, T507) - support for H6 boards without PMIC Tested on Pine64+ and Orange PI Zero2 Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Powered by cgit, Themed by Ted Yin.