aboutsummaryrefslogtreecommitdiff
path: root/package/boot
Commit message (Collapse)AuthorAge
* boot/apex: Restore the APEX boot loaderLinus Walleij2023-10-20
| | | | | | | | | | | | | | | | | | This is a partial revert of the deletion of the IXP4xx target: we restore the APEX boot loader so we can use it for the NSLU2 and related targets. The APEX upstream is as dead as it gets so I have applied OpenWrts old patches on top of the never released v1.6.10 version and forked it into an OpenWrt variant on GitHub. If the upstream comes back alive I will happily switch over to it. The file refers to the external GitHub, I suppose when integrating this patch the file should be copied to OpenWrts file repository and the file link changed. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ipq806x: add support for Extreme Networks AP3935Glen Lee2023-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee <g2lee@yahoo.com>
* filogic: add support for GL.iNet GL-MT6000Jianhui Zhao2023-09-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: * SoC: MediaTek MT7986A 4x A53 * Flash: 8GB EMMC * RAM: 1GB DDR4 * Ethernet: * 2x2.5G RJ45 port (RTL8221B) * 4x1G RJ45 ports (MT7531AE) * WLAN: * 2.4GHz: MT7976GN 4T4R * 5GHz: MT7976AN 4T4R * Button: Reset * LED: 1 x dual color LED * USB: 1 x USB 3.0 * Power: DC 12V 4A * UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC) * JTAG: 9 PIN If you want to use u-boot from OpenWrt, you can upgrade it safely. * bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin * fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip `openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
* uboot-mediatek: sync spi-nand driver with SDKChukun Pan2023-09-29
| | | | | | | | | | | When adding new router support, I found that uboot could not recognize flash: "unknown raw ID xxx". Sync SPI-NAND driver for mediatek to fixes this: * Add support for Winbond W25N01KV 1Gbit chip. * Add support for Etron SPI-NAND chip. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* treewide: Add extra CPE identifierHauke Mehrtens2023-09-25
| | | | | | | This adds some Common Platform Enumerations (CPE) identifiers which I found. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)Elbert Mai2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti U6+ is a dual-band WiFi 6 PoE access point. It is a drop-in upgrade of the U6 lite. Specifications --- - SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz - RAM: 256 MB DDR3-2133 RAM - Flash: 16 MB SPI NOR and 4 GB eMMC - LAN: 1x Gigabit Ethernet with 802.3af/at support - WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6 - LEDs: 1x blue and 1x white - Buttons: 1x reset button Installation --- 1. Power device using a PoE injector or switch 2. Connect via Ethernet to the device with static IP 192.168.1.2 3. SSH into the device with password: ubnt $ ssh ubnt@192.168.1.20 4. Unlock kernel partitions for writing $ echo 5edfacbf > /proc/ubnthal/.uf 5. Confirm correct partitions $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent PARTNAME=kernel0 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent PARTNAME=kernel1 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent PARTNAME=bs 6. Set and confirm bootloader environment $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd_real "run boot_openwrt" $ fw_printenv 7. Copy sysupgrade image to /tmp/openwrt.bin via scp 8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6 $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7 9. Ensure device boots from mmcblk0p6 $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8 10. Reboot the device $ reboot Signed-off-by: Elbert Mai <code@elbertmai.com> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* arm-trusted-firmware-sunxi: update to version 2.9Sebastian Pflieger2023-09-24
| | | | | | | | | - detect die revision used in variants of the Allwinner H616 SoC (H313, T507) - support for H6 boards without PMIC Tested on Pine64+ and Orange PI Zero2 Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
* ipq807x: add support for Netgear WAX620Kristian Skramstad2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz * RAM: 1 GiB of DDR4 600 MHz * Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC) * 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz * UART: Two 4-pin unpopulated headers under the LEDs. Use the header closest to LED 4 and 5. They are marked with a white stroke. TX RX GND, beginning from "4". 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081) Wlan: * 4x4 in 2.4GHz: 802.11b/g/n/ax * 4x4 in 5.0GHz: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz) Power: * PoE+ 802.3at/af 25.5W * DC 12V 2.5A ``` ``` Note: The OpenWrt image is setup with DHCP and not a static IP. 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* uboot-mediatek: add build for mt7981 rfbDaniel Golle2023-09-21
| | | | | | | Improve and package builds for various boot media configurations of the MediaTek MT7981 reference board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: fix copy&paste error in MakefileDaniel Golle2023-09-21
| | | | | | | | | When adding builds for MT7981 the related Makefile sections for MT7986 have apparently been copied, but in one instance the rename from 7986 to 7981 has been omitted. Fix that now. Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mvebu: eDPU: add support for version with external switchRobert Marko2023-09-19
| | | | | | | | | | | | | New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP cage and G.hn IC instead of connecting them directly to the ethernet controllers. In order to use the same image for both boards, U-Boot is responsible for detecting the revision and enabling/disabling DTS nodes. So, to make it easy for users, lets add the pending U-Boot patches to build in OpenWrt. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* sunxi: add support for Bananapi P2 ZeroZoltan HERPAI2023-09-18
| | | | | | | | | | | | | | | CPU: Allwinner H2+ quad-core Cortex-A7 @ 1.2GHz Memory: 512Mb DDR3 Storage: SDcard, 8GB eMMC Network: 10/100M ethernet, optional PoE support, Ampak AP6212 wifi + BT USB: 1x USB 2.0 OTG Other: 40-pin expansion header, mini-HDMI Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: add support for H616 SoC and Orangepi Zero 2Zoltan HERPAI2023-09-18
| | | | | | | | | | | | | | | | | | | Specifications: SoC: Allwinner H616 @ 1.5 Ghz DRAM: 1Gb LPDDR3 Power: 5V USB-C Video: HDMI (Type 2.0A - micro) Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi Storage: microSD / 2Mb SPI flash USB: 1 USB2.0 Host Debug Serial UART Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-envtools: ramips: add support for ALFA Network AX1800RMPiotr Dymacz2023-09-11
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* arm-trusted-firmware-mediatek: fix hang on reboot on MT7622Daniel Golle2023-09-10
| | | | | | | | | With recent updates of TF-A the previously already fixed bug slipped back into the source tree. Again, reorder bl2 init for MT7622 and initialize WDT only after DRAM init has completed to avoid the notorious hang. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: sync mtk-snand driver with SDKDaniel Golle2023-09-10
| | | | | | | | Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988: * Platform data for MT7981 was actually missing and is now added. * Add support for Winbond W25N01KV 1Gbit chip. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Cetron CT3003Patricia Lee2023-09-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **Hardware specification:** - SoC: MediaTek MT7981B 2x A53 - Flash: ESMT F50L1G41LB 128MB - RAM: Nanya NT5CC128M16JR-EK 256MB - Ethernet: 4 x 10/100/1000 Mbps - Switch: MediaTek MT7531AE - WiFi: MediaTek MT7976C - Button: Reset, Mesh - Power: DC 12V 1A - UART: 3.3v, 115200n8 | Layout: | | :-------- | | <Antenna> | | VCC | | GND | | Tx | | Rx | **Flash instructions:** 1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`. 2. Upload the `factory.bin` using the device's Web interface. 3. Click the upgrade button and wait for the process to finish. 4. Access the OpenWrt interface using the same password. 5. Use the 'Restore' function to reset the firmware to its initial state. **Notes:** If you plan to recovery the stock firmware in the future, it's advisable to connect the device via the serial port and enter failsafe mode to back up all the MTD partitions before proceeding the steps above. Signed-off-by: Patricia Lee <patricialee320@gmail.com>
* uboot-rockchip: add suport for Radxa ROCK Pi EJayantajit Gogoi2023-09-05
| | | | | | | | | | | | | | | | | | | | | | | | | Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board. Add pre-built files to fix swig dependencies. Specification: - CPU: Rockchip RK3328 64-bit Quad-core - RAM: DDR3 256MB ~ 2GB - Network: 1 x 10/100/1000M Ethernet 1 x 10/100M Ethernet - USB Host: 1 x USB3.0 Type A HOST 1 x USB2.0 OTG (40-pin pin-header) - Wireless: RTL8723DU/RTL8821CU - Power Supply: Type-C 5V Installation: - Write image to SD Card or EMMC with dd - Boot ROCK Pi E from the SD Card Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
* arm-trusted-firmware-mediatek: enable built-in 2.5G PHY on MT7988Daniel Golle2023-08-28
| | | | | | | | | | Always enable built-in 2.5G PHY on MT7988 for now, so that it can be used. In future it would be nice to be able to switch power and MDIO access via address 0 at run-time in Linux, both, to be able to use external PHYs at address 0 and to reduce power consumption on systems not using the built-in 2.5G PHY. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: fix dependency on TF-A for MT7988 RFB (sdmmc)Daniel Golle2023-08-28
| | | | | | | | | The U-Boot build for the MT7988 reference board booting from SD card wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build even though the 'comb' variant is used. Fix that dependency. Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add builds for UniFi 6 LR v2 and v3Daniel Golle2023-08-28
| | | | | | | While the v2 is nearly identical to v1, v3 uses a different PHY and needs a different build for Ethernet to work in U-Boot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: build fully-featured U-Boot for MT7988 RFBDaniel Golle2023-08-28
| | | | | | | | | | | | | | | | | | Select many potentially useful options for the MT7988 RFB U-Boot builds. The resulting loader is intended as a development tool and intends to be generic. It does *not* have a default bootcmd set, but allows to boot pretty much everything, including EFI executables. To install this U-Boot build to the eMMC: opkg install mmc-utils partx-utils mmc bootpart enable 1 1 /dev/mmcblk0 echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0 dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0 partx -a /dev/mmcblk0 dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-rockchip: fix swig dependency for ROCK64Antonio Flores2023-08-27
| | | | | | Pre build files to fix swig dependency. Signed-off-by: Antonio Flores <antflores627@gmail.com>
* uboot-rockchip: add support for PINE64 ROCK64Antonio Flores2023-08-27
| | | | | | Add uboot support for PINE64 ROCK64, rockchip rk3328 board. Signed-off-by: Antonio Flores <antflores627@gmail.com>
* uboot-sunxi: bump to 2023.04Zoltan HERPAI2023-08-26
| | | | | | | | | | | | | | | | | Compile-tested: all boards Runtime-tested: - Cortex-A8: pcDuino - Cortex-A7: Bananapro, Bananapi M3 - Cortex-A53:Pine64+ Notes: - binman tries to add firmware for the SCP (system control processor), which we don't build, and is optional for the boot process on 64-bit. Disable this via setting the SCP envvar to /dev/null. For further info, see [1] . [1] https://github.com/u-boot/u-boot/blob/master/board/sunxi/README.sunxi64 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* arm-trusted-firmware-mvebu: bump to v2.9Robert Marko2023-08-26
| | | | | | We are using the outdated 2.7 TF-A, so lets update to current v2.9 version. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: update CM3 GCC to 12.3rel1Robert Marko2023-08-26
| | | | | | | | | We are using the outdated 11.2 GCC for CM3, lets update to the current 12.3rel1 version from ARM [1]. [1] https://developer.arm.com/downloads/-/arm-gnu-toolchain-downloads Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump cryptopp to version 8.8Robert Marko2023-08-26
| | | | | | | We are using the outdated Crypto++ version 8.5, so lets update to the current version 8.8. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump mox-boot-builder to current versionRobert Marko2023-08-26
| | | | | | | | | | | | | | | | | We have to move to use git clone as there are no newer tagged releases. Changes: 604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi- b9b9419 Tidy up license information 0290b2c wtmi: Fix typo a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal) f654082 wtmi: Add const qualifier to isr_vector 4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz 189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up 3dac4fe wtmi: Fix detection of Armada 3720 Devel Board 3ca4dfa Bump mox-imager commit Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump mv-ddr-marvell to current versionRobert Marko2023-08-26
| | | | | | | | Changes: 1de442d Convert floating point operations to integer operations ce6770d Modify mv_ddr4_calibration_validate function body to match function header Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* arm-trusted-firmware-mvebu: bump a3700-utils to current versionRobert Marko2023-08-26
| | | | | | | | Changes: a3e1c67 wtmi: Fix linker output sections f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* uboot-envtools: fix parallel buildingRobert Marko2023-08-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recent envtools update to 2023.07.02 has introduced a breakage when trying to parallel build with the following error: /bin/sh: line 1: scripts/basic/fixdep: No such file or directory Luckily it can easily be reproduced locally via a simple script so it was not hard to bisect it down to upstream commit [1]. However, its not that commits fault, it just uncovered an issue with the way we have been building envtools for a long time, maybe even from the package introduction. The issue is that we are trying to build envtools as one of the U-Boot no-dot-config-targets but envtools was newer a valid target for it but since we were creating the config headers that were not actually used it was actually building all this time. Since the blamed commit [1] a tool called printinitialenv is built and now a proper config is actually required in order for prerequisites to get built properly. So, in order to properly fix this (Hopefully for good) lets stop pretending that envtools are a valid no-dot-config-targets target and use the tools-only defconfig which is meant exactly for just building the tools. This will make a minimal config for the U-Boot sandbox target and then envtools will build just fine in parallel mode (I tested with 32 threads). We do hovewer need to override the ARCH passed by OpenWrt and set it to sandbox as otherwise U-Boot will not find the required headers because the ARCH is being overriden to an incorrect one. [1] https://source.denx.de/u-boot/u-boot/-/commit/40b77f2a3ac13a7547c1b7c9c51a4090869de8f4 Fixes: 9db033005210 ("uboot-envtools: update to 2023.07.02") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* uboot-mediatek: increase max. memory regions on mt7988-rfbDaniel Golle2023-08-24
| | | | | | | | | | | WED requires a bunch of additional reserved memory regions. As U-Boot's LMB allocator defaults to a maximum of only 8 regions, this currently makes using WED impossible. Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards with a SoC supporting WED. Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: wax220: cleanup device treeStefan Agner2023-08-22
| | | | | | | Fix compatible string to match what is supported upstream, fix alignment and order MTD partitions according to offset. Signed-off-by: Stefan Agner <stefan@agner.ch>
* uboot-bcm53xx: Add U-Boot for NorthStar BCM53xxLinus Walleij2023-08-20
| | | | | | | | | | | | | | I recently added support for the NorthStar ARM BCM53xx SoCs to the upstream U-Boot. This is a back port on top of the 2023.04 version already imported to OpenWrt with the 5 necessary upstream patches. This is needed to create a small U-Boot for the BCM53xx-based D-Link DIR-890L and I think also the DIR-885L, so that a recent (bigger) kernel can be loaded and executed from the SEAMA partitions on these devices. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* filogic: support Telenor branded ZyXEL EX5700Bjørn Mork2023-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Telenor quirks -------------- The operator specific firmware running on the Telenor branded ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt installation. Notable changes to U-Boot include - environment is stored in RAM and reset to defaults when power cycled - dual partition scheme with "nomimal" or "rescue" systems, falling back to "rescue" unless the OS signals success in 3 attempts - several runtime additions to the device-tree Some of these modifications have side effects requiring workarounds - U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash unless this node exists - U-Boot verifies that the selected rootfs UBI volume exists, and refuses to boot if it doesn't. The chosen "rootfs" volume must contain a squashfs signature even for tftp or initramfs booting. - U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr" variable to the label mac. But "factoryparams" does not always exist. Instead there is a "RIP" volume containing all the factory data. Copying the "RIP" volume to "factoryparams" will fix this Hardware -------- SOC: MediaTek MT7986 RAM: 1GB DDR4 FLASH: 512MB SPI-NAND (Mikron xxx) WIFI: Mediatek MT7986 802.11ax 5 GHz Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz ETH: MediaTek MT7531 Switch + SoC 3 x builtin 1G phy (lan1, lan2, lan3) 2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan) USB: 1 x USB 3.2 Enhanced SuperSpeed port UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.2/24. Rename the image to C0A80101.img. 2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial console, Interrupt the autoboot process by pressing ESC when prompted. 3. Download and boot the OpenWrt initramfs image. $ env set uboot_bootcount 0 $ env set firmware nominal $ tftpboot $ bootm 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Missing features ---------------- - The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but OpenWrt does not correctly configure the output. - The "lan4" and "wan" port LEDs are driven by the GPH211C phys and not configured by OpenWrt. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq807x: add support for Netgear RAX120v2Thomas Kupper2023-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
* uboot-envtools: update to 2023.07.02Stefan Kalscheuer2023-08-15
| | | | | | | | | | | | Update to the latest stable version. This update changes the default lockfile directory from /var/lock to /run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might not even exist, so we add a patch to revert this particular change. [1] https://source.denx.de/u-boot/u-boot/-/commit/aeb40f1166e072856f865d26d42a4bea1ec3a514 Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* uboot-envtools: add u-boot env config for Xiaomi mi-miniIvan Pavlov2023-08-14
| | | | | | Add u-boot env config for Xiaomi mi-mini for using fw_printenv and fw_setenv on this board Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
* uboot-mediatek: bpi-r3: prepare for larger FIT structuresDaniel Golle2023-08-13
| | | | | | | | | Instead of reading only a single 4kiB page, read the first 128kiB to determine the size of an uImage.FIT using 'imsz' or 'imszb'. This will be needed once we add more Device Tree Overlays, which may happen for the BPi-R3 mini. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-tools: fix build on macOS/DarwinFelix Fietkau2023-08-12
| | | | | | Resolve conflicts with the uuid type from darwin system headers Signed-off-by: Felix Fietkau <nbd@nbd.name>
* sunxi: add support for Banana Pi M3Zoltan HERPAI2023-08-11
| | | | | | | | | | | | | | CPU Allwinner A83t Octa-core Cortex A7 @ 1.2GHz Memory 2Gb DDR3 Storage SDcard, SATA (via USB), 8GB eMMC Network 10/100/1000M ethernet, Ampak AP6212 wifi + BT USB 2x USB 2.0 Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-mediatek: fix build for MT7629Daniel Golle2023-07-31
| | | | | | | | Add patch to fix build failure caused by a missing header which had previously been implicitely included. Fixes: 6ddb5f5a65 ("uboot-mediatek: update to version 2023.07.02") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add missing 'memory' nodes to downstream boardsDaniel Golle2023-07-31
| | | | | | | | | | Among the patches adding support for MT7988 also came the switch to use fdtdec_setup_mem_size_base() and no longer rely on CFG_SYS_SDRAM_BASE. Take care of our downstream boards which did not have a 'memory' node in their device trees. Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: fix PKG_MIRROR_HASHDaniel Golle2023-07-31
| | | | | | | | | | Instead of using the hash of the Github-generated tarball use the hash of the tarball generated by the OpenWrt build system (in this case they are different, unfortunately). Reported-by: Chen Minqiang <ptpt52@gmail.com> Fixes: 07dbeb430e ("arm-trusted-firmware-mediatek: update to sources of 2023-07-24") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add patches for MT7988 and builds for RFBDaniel Golle2023-07-29
| | | | | | | Import pending patches adding support for MT7988 and provide builds for the reference board for all possible boot media. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: update to version 2023.07.02Daniel Golle2023-07-29
| | | | | | | | | | Release 2023.07 got tagged wrongly and replaced by follow-up release 2023.07.02. Now using upstream DTS for BPi-R3. Removed two patches which made it upstream, refreshed the rest. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: update to sources of 2023-07-24Daniel Golle2023-07-29
| | | | | | | | Use updated Trusted Firmware-A sources from MediaTek, now stacked on top of the ARM Trusted Firmware-A v2.9 release. Add builds for the newly added MT7988 SoC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-tools: update to version 2.9Daniel Golle2023-07-29
| | | | | | | | | | | | | | | | | | 147f52f3e feat(fiptool): add cca, core_swd, plat cert in FIP 0aaa382fe fix(sptool): fix concurrency issue for SP packages cb666b39d Merge "fix(sptool): fix concurrency issue for SP packages" into integration 0be2475f6 fix: 'sp_mk_generator.py' reference to undef var 1a28f290b fix(sptool): operators "is/is not" in sp_mk_gen.py cf2dd17dd refactor(security): add OpenSSL 1.x compatibility 4daeaf341 fix(sptool): add dependency to SP image 06e69f7c9 feat(fiptool): handle FIP in a disk partition 5a53c6c66 Merge "feat(fiptool): handle FIP in a disk partition" into integration 034a2e3ef refactor(fiptool): move plat_fiptool.mk to tools 0165ddd7c build(fiptool): add object dependency generation c89fdb4a5 Merge "refactor(fiptool): move plat_fiptool.mk to tools" into integration 1b491eead fix(tree): correct some typos Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mvebu: update to version 2023.07.02Oli Ze2023-07-29
| | | | | | | | | | | | Since 2021.07 multiple bugs were introduced that made it impossible to create a bootable target for mvebu. Those issues should be now fixed since 2023.07-rc1. References: #11661 Signed-off-by: Oli Ze <olze@trustserv.de> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs Signed-off-by: Petr Štetiar <ynezz@true.cz> [facelift]
Powered by cgit, Themed by Ted Yin.