aboutsummaryrefslogtreecommitdiff
path: root/package/boot/uboot-envtools
Commit message (Collapse)AuthorAge
* uboot-envtools: replace use of platform_get_bootdevDaniel Golle2024-02-26
| | | | | | Use new function fitblk_get_bootdev in /lib/upgrade/common.sh instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: phase out uImage.FIT partition parserDaniel Golle2024-02-24
| | | | | | | | Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623. Introduce boot device selection for fitblk's /chosen/rootdisk handle, similar to how it is already done on MT7622, MT7986 and MT7988. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: Add support Netgear LBR20Marcin Gajda2024-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem. SoC Type: Qualcomm IPQ4019 RAM: 512 MiB Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC) Bootloader: U-Boot Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink WiFi class AC2200: - radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels - radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz - radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on. Ethernet: 2x1GbE (WAN/LAN1, LAN2) LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white USB ports: No Buttons: 2 Reset and SYNC(WPS) Power: 12 VDC, 2,5 A Connector type: Barrel OpenWRT Installation 1. Simplest way is just do upgrade from webpage with *factory.img 2. You can also do it with standard tool for Netgear's debricking - NMPRFlash 3. Most advanced way is to open device , connect to UART console and : - Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10) - Connect serial console (115200,8n1) to UART connector - Connect TFTP server to RJ-45 port - Stop in u-Boot and run u-Boot command: > setenv serverip 192.168.1.10 > set fdt_high 0x85000000 > tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb > bootm 0x83000000 - Login via ssh - upload or download *sysupgrade.bin ( like wget ... or scp transfer) - Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”) Back to Stock - Download firmware from official Netgear's webpage , it will be *.img file after decompressing. - Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash ) Open the case - Unscrew nuts and remove washers from antenna's conectors. - There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it - Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that. - PCB is screwed with 4Pcs of Torx T10 screws - Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires) - On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg ) BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org. Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* qualcommax: ipq807x: add support for Linksys MX5300Paweł Owoc2024-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: ======== SoC: Qualcomm IPQ8072A Flash: 512MB (Winbond W29N04GZBIBA) RAM: 1GB (2x Nanya DDR3L NT5CC256M16ER-EK) Ethernet: 5x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ac 4x4 (Qualcomm QCA9984 + Skyworks SKY85746-11) - channels 100-169 WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11) IoT: Bluetooth 5, Zigbee and Thread (Qualcomm QCA4024 + Skyworks SE2433T-R) IoT Flash: 4MB (Macronix MX25R3235F) RTC: ST M41T00S LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin image. More details can be found here: https://www.linksys.com/hk/support-article?articleNum=274497 After first boot check actual partition: - fw_printenv -n boot_part and install firmware on second partition using command in case of 2: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and in case of 1: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 2. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd21 0 0 nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd23 0 0 nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 3. Installation from initramfs image using USB FAT32 formatted drive: Stop u-boot and run: - usb start && fatload usb 0:1 $loadaddr openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel 4. Back to the OEM firmware: - mtd -e kernel -n write FW_MX5300_1.1.9.200251_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MX5300_1.1.9.200251_prod.img alt_kernel 5. USB recovery: - fw_setenv usbimage 'openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb' fw_setenv bootusb 'usb start && fatload usb 0:1 $loadaddr $usbimage && bootm $loadaddr' fw_setenv bootcmd 'run bootusb; aq_load_fw && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' Notes: ======== IoT device is accesible over spi. Not yet supported. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq60xx: Add 8devices Mango DVKMantas Pucka2024-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com>
* mediatek: filogic: add BananaPi BPi-R3 miniDaniel Golle2024-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- SoC: MediaTek MT7986A 4x A53 Flash: 128MB SPI-NAND, 8GB eMMC RAM: 2GB DDR4 Ethernet: 2x 2.5GbE (Airoha EN8811H) WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G Interfaces: * M.2 Key-M: PCIe 2.0 x2 for NVMe SSD * M.2 Key-B: USB 3.0 with SIM slot * front USB 2.0 port LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD Button: Reset, internal boot switch Fan: PWM-controlled 5V fan Power: 12V Type-C PD Installation instructions for eMMC ---------------------------------- 0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt running there). 1. Write GPT partition table to eMMC Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to the device /tmp using scp and write it to /dev/mmcblk0: dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0 2. Reboot (to reload partition table) 3. Write bootloader and OpenWrt images Move files to the device /tmp using scp: - openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin - openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip - openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb - openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb Write them to the appropriate partitions: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0 dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3 dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4 dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5 sync 4. Remove the device from power, set boot switch to eMMC and boot into OpenWrt. The device will come up with IP 192.168.1.1 and assume the Ethernet port closer to the USB-C power connector as LAN port. 5. If you like to have Ethernet support inside U-Boot (eg. to boot via TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1: echo 0 > /sys/block/mmcblk0boot1/force_ro dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1 dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1 Installation instructions for NAND ---------------------------------- 0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there by instructions above. Using stock rom or immortalwrt does NOT work!) 1. Write things to NAND Move files to the device /tmp using scp: - openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin - openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip - openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb - openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb Write them to the appropriate locations: mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0 ubidetach -m 1 ubiformat /dev/mtd1 ubiattach -m 1 volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip) ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip cd /lib/firmware/airoha cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976 ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976 volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb) ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb) ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb 3. Remove the device from power, set boot switch to NAND, power up and boot into OpenWrt. Partially based on immortalwrt support for the R3 mini, big thanks for doing the ground work! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblkDaniel Golle2024-02-15
| | | | | | No bootloader changes needed in this case, smooth transition. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblkDaniel Golle2024-02-15
| | | | | | | Modernize bootloader and flash memory layout of the BPi-R64 similar to how it has also been done for the BPi-R3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: mediatek_filogic: update bpi-r3Daniel Golle2024-02-15
| | | | | | Unify env configuration now that BPi-R4 and BPi-R3 both use fitblk. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: filogic: add support for BananaPi R4Daniel Golle2024-02-15
| | | | | | | | Add environment settings for the BananaPi BPI-R4 router board which can boot from (and store its bootloader environment on) micro SD card, SPI-NAND and eMMC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: filogic: de-duplicate UBI env settingsDaniel Golle2024-02-15
| | | | | | | Use function instead of duplicating the env settings on UBI for OpenWrt-built U-Boot over and over. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: backport some usefull patches from v2024.04-rc1Shiji Yang2024-02-11
| | | | | | | | Highlights: - Silence small page read warning. - Autodetect NAND erase size and env sectors. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* uboot-envtools: update to 2024.01Nick Hainke2024-02-09
| | | | | | | | | Update to latest version. Refresh patches: - 002-Revert-tools-env-use-run-to-store-lockfile.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: add Comfast CF-E393AX supportDavid Bentham2024-02-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point. Oem firmware is a custom openwrt 21.02 snapshot version. We can gain access via ssh once we remove the root password. Hardware specification: SoC: MediaTek MT7981A 2x A53 Flash: 128 MB SPI-NAND RAM: 256MB DDR3 Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN) 1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN) Switch: MediaTek MT7531AE WiFi: MediaTek MT7976D LEDS: 1x (Red, Blue and Green) Button: Reset UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | VCC GND TX RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface (http://apipaddress/computer/login.html), and download the configuration(http://apipaddress/computer/config.html). 2. Rename downloaded backup config - 'backup.file to backup.tar.gz', Enter 'fakeroot' command then decompress the configuration: tar -zxf backup.tar.gz 3. Edit 'etc/shadow', update (remove) root password: With password = 'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::' 'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::' to Without password = 'root::0:99999:7:::' 'root::0:99999:7:::' 4. Repack 'etc' directory back to a new backup file: tar -zcf backup-ssh.tar.gz etc/ 5. Rename new config tar.gz file to 'backup-ssh.file' Exit fakeroot - 'exit' 6. Upload new configuration via web interface, now you can SSH with the following: 'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \ -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'. Backup the mtd partitions - https://openwrt.org/docs/guide-user/installation/generic.backup 7. Copy openwrt factory firmware to the tmp folder to install via ssh: 'scp -o HostKeyAlgorithms=+ssh-rsa \ -o PubkeyAcceptedAlgorithms=+ssh-rsa \ *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \ root@192.168.10.1:/tmp/' 'sysupgrade -n -F \ /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin' 8. Once led has stopped flashing - Connect via ssh with the default openwrt ip address - 'ssh root@192.168.1.1' 9. SSH copy the openwrt sysupgrade firmware and upgrade as per the default instructions. Signed-off-by: David Bentham <db260179@gmail.com>
* mediatek: drop NMBM layout for Xiaomi WR30UChuanhong Guo2024-01-23
| | | | | | | | | This reverts commit dcdcfc15115a1038e90f21f5aa41726d9c7e2fe5. This is a firmware for third-party u-boot mod, which should not be carried here by us. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: add support for JDCloud RE-CP-03Tianling Shen2024-01-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: 128GB eMMC RAM: 1GB DDR4 Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B) Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Joylink Power: DC 12V 2A Flash instructions: 1. Download and flash the vendor migration firmware via webUI: https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin (Default address is 192.168.68.1, user root, no password) 2. After device has booted up, write new GPT table: dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync 3. Erase and write new BL2: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync 4. Erase and write new FIP: dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync 5. Set static IP on your PC: IP 192.168.1.254/24, GW 192.168.1.1 6. Serve OpenWrt initramfs image using TFTP server. 7. Cut off the power and re-engage, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. 9. Additionally, if you want to have eMMC recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: add support for Xiaomi AX3000TDim Fish2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **SoC**: MediaTek MT7981B 2x A53 **Flash**: ESMT F50L1G41LB 128MB **RAM**: NT52B128M16JR-FL 256MB **Ethernet**: 4x 10/100/1000 Mbps **Switch**: MediaTek MT7531AE **WiFi**: MediaTek MT7976C **Buttons**: Reset, Mesh **Power**: DC 12V 1A 1. Get ssh access. Supported stock firmware **1.0.47** ``` curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A" curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A ``` 2. Backup stock partitions ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then transfer them to your computer in a safe place. 3. Get firmware information `cat /proc/cmdline` 4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash If **firmware=0** ``` ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` If **firmware=1** ``` ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit reboot ``` Then reboot your router, it should boot to the OpenWrt initramfs system now. 5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin` 1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` `reboot` 2. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 3. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 4. *(Optional **-10Mb** free space) Add recovery boot feature.* ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb ``` 5. Flash Openwrt U-Boot ``` mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2 mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP ``` 6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb` 1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb` 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw `opkg update && opkg install kmod-mtd-rw` `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock images from backup ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Signed-off-by: Dim Fish <dimfish@gmail.com>
* ipq807x: add support for Linksys MX4200 V1 and V2Mohammad Sayful Islam2024-01-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys MX4200 is a 802.11ax Tri-band router/AP. Specifications: * CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 512Mb NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * RGB system led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition fw_printenv -n boot_part - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel Replace (X) with your model version either 1 or 2 Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* mediatek: Add support for D-Link EAGLE PRO AI R32Roland Reinl2024-01-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | R32 is like the M32 part of the EAGLE PRO AI series from D-Link. Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 2 LEDs (Status and Internet, both can be either orange or white) - 2 buttons (WPS and Reset) Compared to M32, the R32 has the following differences: - 4 LAN ports instead of 2 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001 - Individual LEDs for power and internet - MAC address is stored at another offset in the ODM partition MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x81 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment. The support for the M32/R32 already includes support for flashing from the OEM web interface: - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap) Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
* mediatek: filogic: add support ASUS RT-AX59UXavier Franquet2023-12-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (based on support for ASUS RT-AX59U by liushiyou006) SOC: MediaTek MT7986 RAM: 512MB DDR4 FLASH: 128MB SPI-NAND (Winbond W25N01GV) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: MediaTek MT7531 Switch UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Upgrade from AsusWRT to OpenWRT using UART Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin. Connect the PC with TFTP server to the RT-AX59U. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0) Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.70 $ tftpboot 0x46000000 rtax59u.bin $ bootm 0x46000000 Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Upgrade from AsusWRT to OpenWRT using WebUI Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file Wait for OpenWRT to boot (192.168.1.1). Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT. We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g when bit 28 is already set. : Stock : OpenWrt WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4 WLAN 2g (2) : : CA:xx:xx:0D:xx:D4 WLAN 2g (3) : : CE:xx:xx:0D:xx:D4 WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5 WLAN 5g (2) : : CE:xx:xx:1D:xx:D5 WLAN 5g (3) : : C2:xx:xx:1D:xx:D5 WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE WLAN 2g (2) : : 0A:xx:xx:76:xx:BE WLAN 2g (3) : : 0E:xx:xx:76:xx:BE WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF WLAN 5g (2) : : 0E:xx:xx:76:xx:BF WLAN 5g (3) : : 02:xx:xx:76:xx:BF Signed-off-by: Xavier Franquet <xavier@franquet.es>
* mediatek: add support for Routerich AX3000Mikhail Zhilkin2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR is continuation of work under "mediatek: add support for Routerich AX3000" #13703 by the agreement with PR #13703 original author (Maximilian Weinmann <x1@disroot.org>). All reviews from the previous PR were taken into into account. Routerich AX3000 is a wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 256 MiB (ESMT M15T2G16128A) - Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MIMO 2x2 - 5 GHz : a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE) - USB : 1x 2.0 - UART : through-hole on PCB - [J500] GND, TX, RX, 3.3V (115200n8) - Buttons : Mesh, Reset - LEDs : 1x Power (Blue) 1x WiFi 2.4 GHz (Blue) 1x WiFi 5 GHz (Red) 1x Mesh (Blue) 3x LAN activity (Blue) 1x WAN activity (Blue) 2x WAN no-internet (Red) - Power : 12 VDC, 1.5 A Installation ------------ Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface (without keeping settings). Return to stock --------------- Install stock firmware image (without keeping settings) using OpenWrt sysupgrade method. Recovery -------- Connect uart, use u-boot menu to flash stock firmware image or boot OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:b4 | label | | LAN | 24:0f:5e:xx:xx:b5 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* mediatek: add support for Zbtlink ZBT-Z8103AXIan Oderon2023-12-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND No. of Antennas: 6 Note: Upon opening the router, only 5 antennas were connected to the mainboard. Led Layout: Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi Buttons: Reset-Mesh Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Signed-off-by: Ian Oderon <ianoderon@gmail.com>
* uboot-envtools: bump PKG_RELEASERafał Miłecki2023-12-13
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* uboot-envtools: fix reading NVMEM device's compatible valueRafał Miłecki2023-12-13
| | | | | Fixes: fea4ffdef28f ("uboot-envtools: update to 2023.04") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for Rostelecom RT-FE-1AMikhail Zhilkin2023-12-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: No Button: 2 buttons (Reset & WPS) LEDs: - 1x Power (green, unmanaged) - 1x Status (green, gpio) - 1x 2.4G (green, hardware, mt76-phy0) - 1x 2.4G (blue, gpio) - 1x 5G (green, hardware, mt76-phy1) - 1x 5G (blue, gpio) - 5x Ethernet (green, hardware, 4x LAN & WAN) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface (default http://192.168.0.1/) under "admin" account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following block: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" /> </OBJECT> 5. Replace <some value> by a new superadmin password and add a line which enabling superadmin login after. For example, the block after the changes: <OBJECT name="User." type="object" writable="1" encryption="0" > <OBJECT name="1." type="object" writable="1" encryption="0" > <PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" /> <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> </OBJECT> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (superadmin:xxxxxxxxxx, where xxxxxxxxxx is a new password from the p.5) 9. Enable SSH access to the router (Settings -> Access control -> SSH) 10. Connect to the router using SSH shell using superadmin account 11. Run in SSH shell: sh 12. Make a mtd backup (optional, see related section) 13. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 14. Login to the router web interface under admin account 15. Remove dots from the OpenWrt factory image filename 16. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 192.168.0.2 MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | f4:*:66 | | WAN | label + 11 | f4:*:71 | | 2g | label + 2 | f4:*:68 | | 5g | label + 3 | f4:*:69 | +-----+------------+---------+ The label MAC address was found in Factory, 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* uboot-envtools: fix GL-MT2500 offsetDavid Bauer2023-12-03
| | | | | | | | The previous offsets did also work, as they've wrapped back to 0x0. However, in reality the environment starts at offset 0x0 of the u-boot-env MMC partition. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add support for GL.iNet GL-MT2500David Bauer2023-11-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7981BA RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR) MMC: 8GB eMMC (Samsung 8GTF4R) ETH: 1000Base-T LAN (ePHY) 2500Base-T WAN (MaxLinear GPY211C) BTN: 1x Reset Button LED: System (blue/white) VPN (white) USB: 1x USB-A (USB 3.0) UART: 115200 8N1 - Pinout on board next to LAN port Don't connect 3.3V! Known Issues ------------ U-Boot vendor recovery does not seem to accept any images, neither GL.iNet images nor OpenWrt images. Recovery requires serial access! Installation ------------ Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to not retain existing settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-link DAP-1720 A1Rani Hod2023-11-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa <protectivedad@gmail.com> Signed-off-by: Rani Hod <rani.hod@gmail.com>
* uboot-envtools: filogic: reorder alphabeticallyChukun Pan2023-11-25
| | | | | | Reorder scripts to keep alphabetical order. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* uboot-envtools: add support for Zyxel EX5601-T0 ubootmodNicolò Veronese2023-11-25
| | | | | | | | The ubootmod bootlaoder for EX5601-T0 uses two partitions in ubi to store enviroment variables. so proper config is needed. Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* mediatek: add support for Zbtlink ZBT-Z8102AXDaniel Golle2023-11-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MediaTek MT7981B RAM: 1024MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 4 LAN (Gigabit) USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by Ian Ishmael C. Oderon. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add settings for Synology DS213jDaniel Golle2023-11-20
| | | | | | | Add settings to be able to access the U-Boot environment on the Synology DS213j NAS. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add JCG Q30 PRO supportChukun Pan2023-11-19
| | | | | | | The vendor uboot will verify firmware at boot. So add a custom uboot build for this device. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* uboot-envtools: add environment config for MeiG SLT866Daniel Golle2023-11-03
| | | | | | Add configuration to access U-Boot environment on MeiG SLT866. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for GL.iNet GL-S200Weiping Yang2023-10-31
| | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9531(650MHz) RAM: DDR2 128M Flash: SPI NOR 16M + SPI NAND 128M WiFi: 2.4GHz with 2 antennas(WiFi/Thread) Ethernet: 1xLAN(10/100M) 2xWAN(10/100M) Button: 1x Reset Button Switch: 1x Mode switch LED: 1x Blue LED + 1x White LED + 1x Orange LED IOT: Thread + ZigBee/Zwave By uboot web failsafe: Push the reset button for 5 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ramips: add support for ZyXEL LTE5398-M904Milan Krstic2023-10-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS port. Specifications: * SoC: Mediatek MT7621AT * RAM: 256 MB * Flash: 128MB NAND (MX30LF1G18AC) * WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G * Switch: 2 GbE ports MT7530 * LTE/3G: Quectel EG18-EA LTE-A Cat. 18 * SIM: 1 micro-SIM card slot * Buttons: Reset, WPS * LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G) * VoIP: 1 FXS RJ11 port * Power: 12V, 2A UART serial console: 57600,8N1 Unpopulated header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Installation: * Log in as root using ssh to 192.168.1.1 * scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/ * Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit * Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot * Wait for OpenWrt to boot and ssh to root@192.168.1.1 * Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image For mode details about flashing see: 2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19) Unsupported: * FXS/Voice Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
* qualcommax: ipq807x: add support for Netgear WAX630Kristian Skramstad2023-10-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz * RAM: 1 GiB of DDR3 466 MHz * Flash: NAND 512 MiB (Winbond W29N04GZ) * 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L * UART: One 4-pin populated header next to the heatsink and a chip. GND RXD TXD, beginning from the external antennas. 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at * One 100/1000 Gigabit Ethernet Wlan: * 4x4 in 2.4GHz : 802.11b/g/n/ax * 4x4 in 5.0GHz L: 802.11a/n/ac/ax * 4x4 in 5.0GHz H: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H) Power: * 802.3bt/at 30.1W * DC 12V/3.5A Mounting: Wall and ceiling ``` ``` 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to the console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* mediatek: add CMCC RAX3000M supportTianling Shen2023-10-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: 64GB eMMC or 128 MB SPI-NAND RAM: 512MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A - UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | GND TX VCC RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface, and download the configuration. 2. Enter fakeroot, decompress the configuration: tar -zxf cfg_export_config_file.conf 3. Edit 'etc/config/dropbear', set 'enable' to '1'. 4. Edit 'etc/shadow', update (remove) root password: 'root::19523:0:99999:7:::' 5. Repack 'etc' directory: tar -zcf cfg_export_config_file.conf etc/ * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat', just ignore it. 6. Upload new configuration via web interface, now you can SSH to RAX3000M. Check stroage type: Check the label on the back of the device: "CH EC CMIIT ID: xxxx" is eMMC version "CH CMIIT ID: xxxx" is NAND version eMMC Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'factory' part. ('data' partition can be ignored, it's useless.) 2. Write new GPT table: dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync 3. Erase and write new BL2: echo 0 > /sys/block/mmcblk0boot0/force_ro dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync 4. Erase and write new FIP: dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync 5. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 6. Serve OpenWrt initramfs image using TFTP server. 7. Cut off the power and re-engage, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. 9. Additionally, if you want to have eMMC recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync NAND Flash instructions: 1. SSH to RAX3000M, and backup everything, especially 'Factory' part. 2. Erase and write new BL2: mtd erase BL2 mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2 3. Erase and write new FIP: mtd erase FIP mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP 4. Set static IP on your PC: IP 192.168.1.254, GW 192.168.1.1 5. Serve OpenWrt initramfs image using TFTP server. 6. Cut off the power and re-engage, wait for TFTP recovery to complete. 7. After OpenWrt has booted, erase UBI volumes: ubidetach -p /dev/mtd0 ubiformat -y /dev/mtd0 ubiattach -p /dev/mtd0 8. Create new ubootenv volumes: ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB 9. Additionally, if you want to have NAND recovery boot feature: (Don't worry! You will always have TFTP recovery boot feature.) ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb 10. Perform sysupgrade. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ipq806x: add support for Extreme Networks AP3935Glen Lee2023-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee <g2lee@yahoo.com>
* filogic: add support for GL.iNet GL-MT6000Jianhui Zhao2023-09-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: * SoC: MediaTek MT7986A 4x A53 * Flash: 8GB EMMC * RAM: 1GB DDR4 * Ethernet: * 2x2.5G RJ45 port (RTL8221B) * 4x1G RJ45 ports (MT7531AE) * WLAN: * 2.4GHz: MT7976GN 4T4R * 5GHz: MT7976AN 4T4R * Button: Reset * LED: 1 x dual color LED * USB: 1 x USB 3.0 * Power: DC 12V 4A * UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC) * JTAG: 9 PIN If you want to use u-boot from OpenWrt, you can upgrade it safely. * bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin * fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip `openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
* mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)Elbert Mai2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti U6+ is a dual-band WiFi 6 PoE access point. It is a drop-in upgrade of the U6 lite. Specifications --- - SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz - RAM: 256 MB DDR3-2133 RAM - Flash: 16 MB SPI NOR and 4 GB eMMC - LAN: 1x Gigabit Ethernet with 802.3af/at support - WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6 - LEDs: 1x blue and 1x white - Buttons: 1x reset button Installation --- 1. Power device using a PoE injector or switch 2. Connect via Ethernet to the device with static IP 192.168.1.2 3. SSH into the device with password: ubnt $ ssh ubnt@192.168.1.20 4. Unlock kernel partitions for writing $ echo 5edfacbf > /proc/ubnthal/.uf 5. Confirm correct partitions $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent PARTNAME=kernel0 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent PARTNAME=kernel1 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent PARTNAME=bs 6. Set and confirm bootloader environment $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd_real "run boot_openwrt" $ fw_printenv 7. Copy sysupgrade image to /tmp/openwrt.bin via scp 8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6 $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7 9. Ensure device boots from mmcblk0p6 $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8 10. Reboot the device $ reboot Signed-off-by: Elbert Mai <code@elbertmai.com> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq807x: add support for Netgear WAX620Kristian Skramstad2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz * RAM: 1 GiB of DDR4 600 MHz * Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC) * 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz * UART: Two 4-pin unpopulated headers under the LEDs. Use the header closest to LED 4 and 5. They are marked with a white stroke. TX RX GND, beginning from "4". 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081) Wlan: * 4x4 in 2.4GHz: 802.11b/g/n/ax * 4x4 in 5.0GHz: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz) Power: * PoE+ 802.3at/af 25.5W * DC 12V 2.5A ``` ``` Note: The OpenWrt image is setup with DHCP and not a static IP. 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* uboot-envtools: ramips: add support for ALFA Network AX1800RMPiotr Dymacz2023-09-11
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* mediatek: add support for Cetron CT3003Patricia Lee2023-09-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **Hardware specification:** - SoC: MediaTek MT7981B 2x A53 - Flash: ESMT F50L1G41LB 128MB - RAM: Nanya NT5CC128M16JR-EK 256MB - Ethernet: 4 x 10/100/1000 Mbps - Switch: MediaTek MT7531AE - WiFi: MediaTek MT7976C - Button: Reset, Mesh - Power: DC 12V 1A - UART: 3.3v, 115200n8 | Layout: | | :-------- | | <Antenna> | | VCC | | GND | | Tx | | Rx | **Flash instructions:** 1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`. 2. Upload the `factory.bin` using the device's Web interface. 3. Click the upgrade button and wait for the process to finish. 4. Access the OpenWrt interface using the same password. 5. Use the 'Restore' function to reset the firmware to its initial state. **Notes:** If you plan to recovery the stock firmware in the future, it's advisable to connect the device via the serial port and enter failsafe mode to back up all the MTD partitions before proceeding the steps above. Signed-off-by: Patricia Lee <patricialee320@gmail.com>
* uboot-envtools: fix parallel buildingRobert Marko2023-08-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recent envtools update to 2023.07.02 has introduced a breakage when trying to parallel build with the following error: /bin/sh: line 1: scripts/basic/fixdep: No such file or directory Luckily it can easily be reproduced locally via a simple script so it was not hard to bisect it down to upstream commit [1]. However, its not that commits fault, it just uncovered an issue with the way we have been building envtools for a long time, maybe even from the package introduction. The issue is that we are trying to build envtools as one of the U-Boot no-dot-config-targets but envtools was newer a valid target for it but since we were creating the config headers that were not actually used it was actually building all this time. Since the blamed commit [1] a tool called printinitialenv is built and now a proper config is actually required in order for prerequisites to get built properly. So, in order to properly fix this (Hopefully for good) lets stop pretending that envtools are a valid no-dot-config-targets target and use the tools-only defconfig which is meant exactly for just building the tools. This will make a minimal config for the U-Boot sandbox target and then envtools will build just fine in parallel mode (I tested with 32 threads). We do hovewer need to override the ARCH passed by OpenWrt and set it to sandbox as otherwise U-Boot will not find the required headers because the ARCH is being overriden to an incorrect one. [1] https://source.denx.de/u-boot/u-boot/-/commit/40b77f2a3ac13a7547c1b7c9c51a4090869de8f4 Fixes: 9db033005210 ("uboot-envtools: update to 2023.07.02") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mediatek: filogic: wax220: cleanup device treeStefan Agner2023-08-22
| | | | | | | Fix compatible string to match what is supported upstream, fix alignment and order MTD partitions according to offset. Signed-off-by: Stefan Agner <stefan@agner.ch>
* filogic: support Telenor branded ZyXEL EX5700Bjørn Mork2023-08-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Telenor quirks -------------- The operator specific firmware running on the Telenor branded ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt installation. Notable changes to U-Boot include - environment is stored in RAM and reset to defaults when power cycled - dual partition scheme with "nomimal" or "rescue" systems, falling back to "rescue" unless the OS signals success in 3 attempts - several runtime additions to the device-tree Some of these modifications have side effects requiring workarounds - U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash unless this node exists - U-Boot verifies that the selected rootfs UBI volume exists, and refuses to boot if it doesn't. The chosen "rootfs" volume must contain a squashfs signature even for tftp or initramfs booting. - U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr" variable to the label mac. But "factoryparams" does not always exist. Instead there is a "RIP" volume containing all the factory data. Copying the "RIP" volume to "factoryparams" will fix this Hardware -------- SOC: MediaTek MT7986 RAM: 1GB DDR4 FLASH: 512MB SPI-NAND (Mikron xxx) WIFI: Mediatek MT7986 802.11ax 5 GHz Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz ETH: MediaTek MT7531 Switch + SoC 3 x builtin 1G phy (lan1, lan2, lan3) 2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan) USB: 1 x USB 3.2 Enhanced SuperSpeed port UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.2/24. Rename the image to C0A80101.img. 2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial console, Interrupt the autoboot process by pressing ESC when prompted. 3. Download and boot the OpenWrt initramfs image. $ env set uboot_bootcount 0 $ env set firmware nominal $ tftpboot $ bootm 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Missing features ---------------- - The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but OpenWrt does not correctly configure the output. - The "lan4" and "wan" port LEDs are driven by the GPH211C phys and not configured by OpenWrt. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq807x: add support for Netgear RAX120v2Thomas Kupper2023-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
* uboot-envtools: update to 2023.07.02Stefan Kalscheuer2023-08-15
| | | | | | | | | | | | Update to the latest stable version. This update changes the default lockfile directory from /var/lock to /run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might not even exist, so we add a patch to revert this particular change. [1] https://source.denx.de/u-boot/u-boot/-/commit/aeb40f1166e072856f865d26d42a4bea1ec3a514 Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* uboot-envtools: add u-boot env config for Xiaomi mi-miniIvan Pavlov2023-08-14
| | | | | | Add u-boot env config for Xiaomi mi-mini for using fw_printenv and fw_setenv on this board Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Powered by cgit, Themed by Ted Yin.