aboutsummaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAge
* mxs: add testing kernel 6.1Zoltan HERPAI2023-07-01
| | | | | | Runtime-tested on Olinuxino Maxi. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* rpcd: update to latest git HEADHauke Mehrtens2023-07-01
| | | | | | c07ab2f iwinfo: update byte counter to 64bit Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iwinfo: update to latest git HEADHauke Mehrtens2023-07-01
| | | | | | | | | | d1f07cf devices: add device id for Atheros AR9287 and AR9380 65ea345 nl80211: constify a few arrays ca79f64 lib: report byte counters as 64 bit values This contains an ABI change, increase the ABI version too. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* libnl-tiny: update to latest git HEADHauke Mehrtens2023-07-01
| | | | | | d433990 Make struct nla_policy and struct nlattr const Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* linux-firmware: ibt-firmware: install sfi/ddc files for AX210 cardMathew McBride2023-07-01
| | | | | | | | | | | | | | | | | | When using an Intel AX210 card, the Bluetooth hci interface failed to start due to a missing "ibt-0041-0041.sfi" file. Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0041-0041.sfi (-2) A device specific configuration file (DDC) is also required: Bluetooth: hci0: Found device firmware: intel/ibt-0041-0041.sfi Bluetooth: hci0: Waiting for firmware download to complete ... Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0041-0041.ddc Bluetooth: hci0: Applying Intel DDC parameters completed Bluetooth: hci0: Firmware timestamp 2023.13 buildtype 1 build 62562 Fixes: #8558 Signed-off-by: Mathew McBride <matt@traverse.com.au>
* treewide: remove CONFIG_FRAME_WARN from kernel configsRobert Marko2023-07-01
| | | | | | | CONFIG_FRAME_WARN is set dynamically, so there is no need for it to be set in target kernel configs, so lets remove it from all configs. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* generic: filter out CONFIG_FRAME_WARNRobert Marko2023-07-01
| | | | | | | | | | | | | CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the target type dynamically since commit: 16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target"). However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up in multiple target configs during refreshes. So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it ending up in more target configs. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* kernel: bump 5.15 to 5.15.119John Audia2023-07-01
| | | | | | | | Build system: x86_64 Build-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3 Run-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* mxs: rework image generationZoltan HERPAI2023-06-30
| | | | | | | | Migrate to "new" image generation method. Device profiles will be generated based on image/Makefile instead of profiles/ , which will also allow to automatically build images for all supported devices via buildbot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ramips/mt7621: disable the cpufreq driverFelix Fietkau2023-06-30
| | | | | | It causes a noticeable performance decrease Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix mesh fast tx cache issuesFelix Fietkau2023-06-30
| | | | | | Split the cache by tx type in order to avoid packet drop issues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: update to the latest versionFelix Fietkau2023-06-29
| | | | | | | | | | 493e1589bc8b bridge: fix coverity false positive report 03a619947717 bridge: add support for configuring extra vlans for the bridge itself 4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration 255b4d5c472e wireless: fix handling config reload with reconf=1 1ab992a74b43 wireless: fix another reconf issue Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ucode: update to the latest versionFelix Fietkau2023-06-29
| | | | | | | | | | | | | | | | | | | | | | | | | | 9986b839595d ci: unbreak failing builds by using fixed gh-actions-openwrt-ci-sdk 77c961e20eda ci: fix broken imx6-generic SDK build 86107a647cb0 ci: cancel concurrent builds ed543d8bf481 ci: update the workflows 11d5f8840002 Merge pull request #151 from ynezz/ynezz/unbreak-ci b934ce815ff2 program: fix memory leak in read_sourceinfo b0baf043e64c Merge pull request #152 from Ansuel/fix-memory-leak 740e2501fdca main: add user specified library search paths before default path 15f1a669e8e2 struct: remove state->len 29edb011caf1 ubus: add support for strings containing null bytes 2b4346bfdc67 vm: clear vm->alloc_refs in uc_gc_common b213bd120d55 Merge pull request #150 from nbd168/misc-improvements 66520ebe27ae vm: immediately release arguments on calls with invalid spreads 07cc72a77e3b README.md: fix debian dependencies d048ea88fe71 compiler: fix memory leak in uc_compiler_compile_import on early exit 7b7e22dcdf02 Merge pull request #155 from luizluca/luizluca-patch-1 d656d150905e types: implement ucv_object_sort() d72eebeb168b lib: support object ordering in `uc_sort()` ed1f0133c870 nl80211: add constants for iftypes 3ffb046c59a6 Merge pull request #156 from nbd168/nl80211-iftypes c7d84aae0969 Merge pull request #153 from jow-/lib-sort-object-support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mt76: update to the latest versionFelix Fietkau2023-06-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2c9c8ffe9d8c wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll 3365c80f4202 wifi: mt76: connac: fix stats->tx_bytes calculation b69d82130b47 wifi: mt76: connac: do not check WED status for non-mmio devices 1f9cd65b55d7 wifi: mt76: mt7921e: fix probe timeout after reboot 42dace9ce247 wifi: mt76: mt7921: Fix use-after-free in fw features query. 540adbb38205 wifi: mt76: mt7921: add Netgear AXE3000 (A8000) support 150e2d0ffc0c wifi: mt76: mt7996: fix possible NULL pointer dereference in mt7996_mac_write_txwi() 5b7519be2bf6 wifi: mt76: mt7996: fix endianness of MT_TXD6_TX_RATE 40f6e433f747 wifi: mt76: mt76x02: remove WEP support 84ea1a24f5b5 mt76: mt7921: don't assume adequate headroom for SDIO headers 5c28e17f8c78 wifi: mt76: mt7996: fix header translation logic 2386cec860fa wifi: mt76: mt7996: enable BSS_CHANGED_MU_GROUPS support 748d4a2bfebd wifi: mt76: mt7615: enable BSS_CHANGED_MU_GROUPS support 458ad0af21be wifi: mt76: enable UNII-4 channel 177 support 7fb046011293 wifi: mt76: mt7915: fix background radar event being blocked d2a77a9954bb wifi: mt76: mt7915: report tx retries/failed counts for non-WED path f76b102b09ca wifi: mt76: mt7915: rework tx packets counting when WED is active 5637d9e37d9e wifi: mt76: mt7915: rework tx bytes counting when WED is active 34bdc7fcb4c0 wifi: mt76: report non-binding skb tx rate when WED is active d71aa7b992a3 wifi: mt76: mt7915: drop return in mt7915_sta_statistics 251c363c3087 wifi: mt76: mt7996: drop return in mt7996_sta_statistics 150bb95cb153 wifi: mt76: mt7921: do not support one stream on secondary antenna only d480c3281f21 wifi: mt76: mt7921: remove macro duplication in regs.h 18b1027e5b6e wifi: mt76: mt7915: move mib_stats structure in mt76.h 25ec4b91020e wifi: mt76: mt7996: rely on mib_stats shared definition 6541afa88b3b wifi: mt76: mt7921: rely on mib_stats shared definition eeb60eb9a5a0 wifi: mt76: mt7915: add support for MT7981 [sync with upstream] d5b7e6a3d735 wifi: mt76: mt7921e: report tx retries/failed counts in tx free event f0f19cea6646 wifi: mt76: mt7921: fix skb leak by txs missing in AMSDU edd8a830f6e3 wifi: mt76: add tx_nss histogram to ethtool stats e48235308b3e wifi: mt76: mt7915: accumulate mu-mimo ofdma muru stats a729242363d9 wifi: mt76: mt7921: fix non-PSC channel scan fail 8d52436ee0cd wifi: mt76: mt7921: Support temp sensor d152c8688c14 wifi: mt76: mt7915: disable WFDMA Tx/Rx during SER recovery d07785c344ac wifi: mt76: mt7996: disable WFDMA Tx/Rx during SER recovery 2a19784137f9 wifi: mt76: mt7921: make mt7921_mac_sta_poll static da8e33a15e71 wifi: mt76: mt7915: fix command timeout in AP stop period cc58d5c4a9c9 mt76: mt7996: rely on mt76_sta_stats in mt76_wcid 98a37c82a373 wifi: mt76: mt7921: get rid of MT7921_RESET_TIMEOUT marco ece724cf562b wifi: mt76: mt7996: move radio ctrl commands to proper functions 527cbbc5ede7 wifi: mt76: connac: add support for dsp firmware download 44e323340637 wifi: mt76: mt7996: fix bss wlan_idx when sending bss_info command 63f0053df07a wifi: mt76: mt7996: enable VHT extended NSS BW feature e1bb4ef7b2bb wifi: mt76: connac: add support to set ifs time by mcu command 080ca19cc686 wifi: mt76: mt7996: use correct phy for background radar event 2c163f1812a3 wifi: mt76: mt7996: fix WA event ring size b511a437ace4 wifi: mt76: mt7996: add muru support ece67c98dc1c wifi: mt76: mt7996: increase tx token size 7c2515d85117 wifi: mt76: mt7921e: fix init command fail with enabled device 30706095c566 wifi: mt76: mt7915: move sta_poll_list and sta_poll_lock in mt76_dev b06ed10ee271 wifi: mt76: mt7603: rely on shared sta_poll_list and sta_poll_lock b59bdae339de wifi: mt76: mt7615: rely on shared sta_poll_list and sta_poll_lock 6da2e0e4ef54 wifi: mt76: mt7996: rely on shared sta_poll_list and sta_poll_lock b19d3ad88e8b wifi: mt76: mt7921: rely on shared sta_poll_list and sta_poll_lock 595b033275a3 wifi: mt76: mt7915: move poll_list in mt76_wcid 16fcad171849 wifi: mt76: mt7603: rely on shared poll_list field e19f84091d2e wifi: mt76: mt7615: rely on shared poll_list field b87e4dad1e84 wifi: mt76: mt7996: rely on shared poll_list field 6d7950e258d0 wifi: mt76: mt7921: rely on shared poll_list field f5c5eece5038 wifi: mt76: move ampdu_state in mt76_wcid 7e44467469fe mt76: connac: move more mt7921/mt7915 mac shared code in connac lib 39a70710ddcd wifi: mt76: move rate info in mt76_vif 0dc4326991df wifi: mt76: connac: move connac3 definitions in mt76_connac3_mac.h 29cfabbb4b90 wifi: mt76: connac: add connac3 mac library d60b401867f4 linux-firmware: update firmware for MT7922 WiFi device 9404601a6c97 linux-firmware: update firmware for MT7922 WiFi device 2f851902d6b1 linux-firmware: update firmware for MT7921 WiFi device f36b921692b9 Revert "wifi: mt76: mt76x02: remove WEP support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: net: phy: realtek: fix rtl822x_probe on unsupported devicesMartin Schiller2023-06-27
| | | | | | | | Calling rtl822x_probe() on phy devices which uses the rtl822x_read_mmd() and rtl822x_write_mmd() functions makes no sense and the probe ends with an EOPNOTSUPP error. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* kernel: qca-nss-dp: simplify compile argumentsRobert Marko2023-06-26
| | | | | | | Instead of manually passing arguments, lets just switch to using $(KERNEL_MAKE). Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: qca-nss-dp: update to 12.4.5.r1Robert Marko2023-06-26
| | | | | | | | Qualcomm has finally started the preparatory work in order to support kernel 6.1, so lets make use of that and update NSS-DP 12.4.5.r1 which allows us to drop almost some of the patches. Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: qca-ssdk: update to 12.4.5.r1Robert Marko2023-06-26
| | | | | | | | | | Qualcomm has finally started the preparatory work in order to support kernel 6.1, so lets make use of that and update SSDK 12.4.5.r1 which allows us to drop almost all of the patches. Lets also install the forgotten SSDK netlink header. Signed-off-by: Robert Marko <robimarko@gmail.com>
* arm-trusted-firmware-rockchip: add m0 gcc toolchainTianling Shen2023-06-25
| | | | | | | | | | | rk3399 ATF requires arm toolchain to build the m0 pmu driver. As OpenWrt doesn't ship this toolchain so download the prebuilt one just like what we did in arm-trusted-firmware-mvebu. Fixes: 5d1cb52da062 ("arm-trusted-firmware-rockchip: Update to 2.9") Reported-by: Wurzer Juergen <wurzer.juergen@gmail.com> Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* procd: update to latest git HEADHauke Mehrtens2023-06-25
| | | | | | | 122a5e3 Revert "sysupgrade: print errno on failure" 2db8365 system: add RISC-V CPU info Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* rpcd: update to latest git HEADHauke Mehrtens2023-06-25
| | | | | | 31c3907 file: strengthen exec access control Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* uhttpd: update to latest git HEADHauke Mehrtens2023-06-25
| | | | | | 34a8a74 uhttpd/file: fix string out of buffer range on uh_defer_script Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: phy: motorcomm: Fix compileHauke Mehrtens2023-06-25
| | | | | | Fix compilation on starfive target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "mt76: update to the latest version"Felix Fietkau2023-06-25
| | | | | | | This reverts commit 901af2718957fc878279073e9b917458144c75a4. Will be re-applied once crash issues have been figured out and resolved Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: do not print error log when mdio bus is disabledShiji Yang2023-06-25
| | | | | | | | | The mdio bus is used to control externel switch. In most cases, they are disabled, which is the normal behavior. Treating this as an error makes no sense, so we need to change the notification level from error to info. Fixes: a2acdf960704 ("ramips: mt7620: remove useless GMAC nodes") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: backport upstream mt762x PCIe driver error log fixesShiji Yang2023-06-25
| | | | | | | | | | | | | | | | | | | | These patches silence some mt762x PCIe driver error messeges by removing the useless debugging codes and replacing incorrectly used 'dev_err()' with 'dev_info()': PCI: mt7621: Use dev_info() to log PCIe card detection [1] mips: pci-mt7620: do not print NFTS register value as error log [2] mips: pci-mt7620: use dev_info() to log PCIe device detection result [3] Patch [1] has already been merged into the Linux 6.3 branch. Patches [2] and [3] have been merged into the "mips-next" tree, and they will be part of the upcoming Linux 6.5. [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v6.4-rc7&id=50233e105a0332ec0f3bc83180c416e6b200471e [2] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=9f9a035e6156a57d9da062b26d2a48d031744a1e [3] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=89ec9bbe60b61cc6ae3eddd6d4f43e128f8a88de Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for D-Link DIR-806A B1 routerAlexey Bartenev2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General specification: SoC Type: MediaTek MT7620A (580MHz) ROM: 8 MB SPI-NOR (MX25L6406E) RAM: 64 MB DDR (W9751G6KB-25) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Wireless: 5 GHz (MediaTek MT7610EN): ac/n Buttons: 2 button (POWER, WPS/RESET) Bootloader: U-Boot 1.1.3 Power: 12 VDC, 0.5 A MACs: | LAN | [Factory + 0x04] - 2 | | WLAN 2.4g | [Factory + 0x04] - 1 | | WLAN 5g | [Factory + 0x8004] - 3 | | WAN | [Factory + 0x04] - 2 | OEM easy installation: 1. Use a PC to browse to http://192.168.0.1. 2. Go to the System section and open the Firmware Update section. 3. Under the Local Update at the right, click on the CHOOSE FILE... 4. When a modal window appears, choose the firmware file and click on the Open. 5. Next click on the UPDATE FIRMWARE button and upload the firmware image. Wait for the router to flash and reboot. OEM installation using the TFTP method (need level converter): 1. Download the latest firmware image. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.0.180 and subnet mask 255.255.255.0. 5. Connect serial port (57600 8N1) and turn on the router. 6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load system code then write to Flash via TFTP."). 7. Press Y key when show "Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)" Input device IP (192.168.0.1) ==:192.168.0.1 Input server IP (192.168.0.180) ==:192.168.0.180 Input Linux Kernel filename () ==:firmware_name The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me>
* layerscape: add patches for SFP support on DPAA2 platformsMathew McBride2023-06-25
| | | | | | | | | | | | | | | | | | This is required for managed operation of the SFP ports on the Ten64 (LS1088A) and other boards. The two issues resolved are: - Validation of 10G SFP link modes fail as Linux did not consider the equivalence of modes like XFI, 10GBase-R - Fix a locking issue that prevented the system rebooting when SFP ports were controlled by the SFP driver. Please note, these patches are replaced by upstream ones in 6.x, see: commit 61ec9a8154a5 ("armvirt: add SFP support patches for NXP Layerscape DPAA2 platforms") in OpenWrt for the relevant patches. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: armv8_64b: add Traverse Ten64 NAND variantMathew McBride2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC. It is capable of booting both standard Linux distributions from disk devices, using EFI, and booting OpenWrt from NAND. See the online manual for more information, including the flash layout[2]. This patchset adds support for generating Ten64 images for NAND boot. For disk boot, one can use the EFI support that was recently added to the armvirt target. We previously supported NAND users by building inside our armvirt/EFI target[3], but this approach is not suitable for OpenWrt upstream. Users who used our supplied NAND images will be able to upgrade to this via sysupgrade. Signed-off-by: Mathew McBride <matt@traverse.com.au> [1] - https://www.traverse.com.au/hardware/ten64 [2] - https://ten64doc.traverse.com.au/hardware/flash/ [3] - Example: https://gitlab.com/traversetech/ls1088firmware/openwrt/-/commit/285e4360e1604eb466880d245d48efd9962143a5
* ipq4019: add support for ZTE MF287+ aka DreiNeoAndreas Böhler2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ipq40xx: Enable gpio-restart in kernel configurationAndreas Böhler2023-06-25
| | | | | | | Some ZTE devices require the gpio-restart driver to support restarting the LTE modem along with OpenWrt Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add Edimax BR-6208AC V2 supportStefan Weil2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: Edimax BR-6208AC V2 - SoC: MT7620A - Flash: 16 MiB - RAM: 64 MiB - Switch: 1 WAN, 3 LAN (10/100 Mbps) - WiFi: MT7620 2.4 GHz + MT7610E 5 GHz - LEDs: 1x POWER (green, not configurable) 1x Firmware (green, configurable) 1x Internet (green, configurable) 1x VPN (green, configurable) 1x 2.4G (green, not configurable) 1x 5G (green, not configurable) Normal installation: - Upload the sysupgrade image via the default web interface Installation with U-Boot and TFTP: - Requires a TFTP server which provides the sysupgrade image - Requires a connection to the serial port of the device, rate 57600 Signed-off-by: Stefan Weil <sw@weilnetz.de>
* ath79: add support for MikroTik RB951G-2HnDMichał Kępień2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951G-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add kernel support for the Mikrotik RB951G board"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s - 1x PoE in (port 1, 8-30 V input) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 8x LED: - 1x power (green, not configurable) - 1x user (green, not configurable) - 5x GE ports (green, not configurable) - 1x wireless (green, not configurable) - 1x button (restart) Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be GPIO-controllable, which was also the case for older OpenWRT versions that supported this board via a mach file. The Ethernet port LEDs are controlled by the switch chip. See https://mikrotik.com/product/RB951G-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* ath79: mikrotik: extract common bits for RB951x-2HnD devicesMichał Kępień2023-06-25
| | | | | | | | Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are very similar devices. Extract the DTS bits that are identical for these two boards to a separate DTSI file. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* ath79: 5.15: fix not exported sym ath79_pll_baseLuiz Angelo Daros de Luca2023-06-25
| | | | | | | | | | ath79_pll_base was declared as extern but no code exported it. Anyone including arch/mips/include/asm/mach-ath79/ath79.h and compiled as a module would break with: ERROR: modpost: "ath79_pll_base" [drivers/net/ethernet/atheros/ag71xx/ag71xx.ko] undefined! Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* arm-trusted-firmware-rockchip: Update to 2.9Tianling Shen2023-06-25
| | | | | | Switch to standard TF-A build. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: Add support for MOXA AWK-1137CMaximilian Martin2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 * 128 MB of RAM * 16 MB of SPI NOR flash * 2x 10/100 Mbps Ethernet * 2T2R 2.4/5 GHz Wi-Fi * 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * 2x fast ethernet - lan1 + builtin switch port 1 + used as WAN interface - lan2 + builtin switch port 2 + used as LAN interface * 9-30V DC * external antennas Flashing instructions: ====================== Log in to https://192.168.127.253/ Username: admin Password: moxa Open Maintenance > Firmware Upgrade and install the factory image. Serial console access: ====================== Connect a RS232-USB converter to the maintenance port. Pinout: (reset button left) [GND] [NC] [RX] [TX] Firmware Recovery: ================== When the WLAN and SYS LEDs are flashing, the device is in recovery mode. Serial console access is required to proceed with recovery. Download the original image from MOXA and rename it to 'awk-1137c.rom'. Set up a TFTP server at 192.168.127.1 and connect to a lan port. Follow the instructions on the serial console to start the recovery. Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
* mediatek: add support for Mercusys MR90X v1Mikhail Zhilkin2023-06-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Mercusys MR90X(EU) v1 router. Device specification -------------------- SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit RAM: MediaTek MT7986BLA (512MB) Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2) WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4 WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4 LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs on ethernet ports Button: 1 (Reset) USB ports: No Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART) --------------------- V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect The R3 (TX line) and R6 (RX line) are absent on the PCB. You should solder them or solder the jumpers. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Once inside OpenWrt, set / update env variables: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Installation (without UART) --------------------------- 1. Login as root via SSH (router IP, port 20001, password - your web interface password) 2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and SSH settings from the p.1) 3. Add a newline after "#!/bin/sh": telnetd -l /bin/login.sh 4. Save "65-iptv" file 5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and save 6. Make sure that telnetd is running: netstat -ltunp | grep 23 7. Login via telnet to router IP, port 23 (no username and password are required) 8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the router (e.g., using WinSCP and SSH settings from the p.1) 9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to download and upload the full version of busybox to the router. For example, from here: https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64 Upload busybox-arm64 to the /tmp dir of the router and run: in the telnet shell: cd /tmp chmod a+x busybox-arm64 10. Check "initramfs-kernel.bin" size: du -h initramfs-kernel.bin 11. Delete old and create new "kernel" volume with appropriate size (greater than "initramfs-kernel.bin" size): ubirmvol /dev/ubi0 -N kernel ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB 12. Write OpenWrt "initramfs-kernel.bin" to the flash: ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin 13. u-boot-env can be empty so lets create it (or overwrite it if it already exists) with the necessary values: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 14. Reboot to OpenWrt initramfs: reboot 15. Login as root via SSH (IP 192.168.1.1, port 22) 16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router 17. Run sysupgrade: sysupgrade -n /tmp/sysupgrade.bin Recovery -------- 1. Press Reset button and power on the router 2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and upload the OEM firmware Recovery (UART) --------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Do what you need (restore partitions from a backup, install OpenWrt etc.) Stock layout ------------ 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" ubi0/ubi1 format ---------------- U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 00:eb:xx:xx:xx:be | label | | LAN | 00:eb:xx:xx:xx:be | label | | WAN | 00:eb:xx:xx:xx:bf | label+1 | | WLAN 2g | 00:eb:xx:xx:xx:be | label | | WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". OEM wireless eeprom is also there (file "MT7986_EEPROM.bin"). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ipq40xx: meraki-mr33, meraki-mr74: disable image generationLech Perczak2023-06-25
| | | | | | | | | | | | | After migrating to kernel 5.15, upgrading causes the units to become soft-bricked, hanging forever at the kernel startup. Kernel size limitation of 4000000 bytes is suspected here, but this is not fully confirmed. Disable the images to protect users from inadvertent bricking of units, because recovery of those is painful with Cisco's U-boot, until the root cause is found and fixed. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* kernel: migrate FORCE_MAX_ZONEORDER to ARCH_FORCE_MAX_ORDER for 6.1Stefan Kalscheuer2023-06-25
| | | | | | | | | | The flag FORCE_MAX_ZONEORDER was renamed to ARCH_FORCE_MAX_ORDER in Kernel 6.1 [1]. Rename the flag in generic Kconfig and remove it from target configs. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=0192445cb2f7ed1cd7a95a0fc8c7645480baba25 Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* bcm53xx: add Wavlink Quantum DAX/WL-WN538A8 as alt nameDavide Fioravanti2023-06-25
| | | | | | | As already documented in the wiki (https://openwrt.org/toh/wavlink/quantum_dax_wn538a8), this router is based on the Phicomm K3. Just the flashing method is different Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: fix lan leds for Wavlink WL-WN535K1Davide Fioravanti2023-06-25
| | | | | | | | | Previously both lan1 and lan2 leds were wrongly labelled as lan2. Moreover they were connected to the wrong lan port. Fixes 8fde82095ba0 ("ramips: add support for Wavlink WL-WN535K1") Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com> Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* CI: drop unused reusable workflow and dockerfilesChristian Marangi2023-06-25
| | | | | | | Drop unused reusable workflow and dockerfiles now that we moved them to a dedicated repository. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* CI: migrate each workflow to use reusable workflow from dedicated repoChristian Marangi2023-06-25
| | | | | | | | Migrate each workflow to use reusable workflow from dedicated repo to skip pushing CI related commits to openwrt and better track versioning of CI workflow. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* odhcpd: bump to latest git HEADChristian Marangi2023-06-24
| | | | | | | 5211264 odhcpd: add support for dhcpv6_pd_min_len parameter c6bff6f router: Add PREF64 (RFC 8781) support Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: bump 6.1 to 6.1.35John Audia2023-06-23
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.118John Audia2023-06-23
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mt76: update to the latest versionFelix Fietkau2023-06-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2c9c8ffe9d8c wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll 3365c80f4202 wifi: mt76: connac: fix stats->tx_bytes calculation b69d82130b47 wifi: mt76: connac: do not check WED status for non-mmio devices 1f9cd65b55d7 wifi: mt76: mt7921e: fix probe timeout after reboot 42dace9ce247 wifi: mt76: mt7921: Fix use-after-free in fw features query. 540adbb38205 wifi: mt76: mt7921: add Netgear AXE3000 (A8000) support 150e2d0ffc0c wifi: mt76: mt7996: fix possible NULL pointer dereference in mt7996_mac_write_txwi() 5b7519be2bf6 wifi: mt76: mt7996: fix endianness of MT_TXD6_TX_RATE 40f6e433f747 wifi: mt76: mt76x02: remove WEP support 84ea1a24f5b5 mt76: mt7921: don't assume adequate headroom for SDIO headers 5c28e17f8c78 wifi: mt76: mt7996: fix header translation logic 2386cec860fa wifi: mt76: mt7996: enable BSS_CHANGED_MU_GROUPS support 748d4a2bfebd wifi: mt76: mt7615: enable BSS_CHANGED_MU_GROUPS support 458ad0af21be wifi: mt76: enable UNII-4 channel 177 support 7fb046011293 wifi: mt76: mt7915: fix background radar event being blocked d2a77a9954bb wifi: mt76: mt7915: report tx retries/failed counts for non-WED path f76b102b09ca wifi: mt76: mt7915: rework tx packets counting when WED is active 5637d9e37d9e wifi: mt76: mt7915: rework tx bytes counting when WED is active 34bdc7fcb4c0 wifi: mt76: report non-binding skb tx rate when WED is active d71aa7b992a3 wifi: mt76: mt7915: drop return in mt7915_sta_statistics 251c363c3087 wifi: mt76: mt7996: drop return in mt7996_sta_statistics 150bb95cb153 wifi: mt76: mt7921: do not support one stream on secondary antenna only d480c3281f21 wifi: mt76: mt7921: remove macro duplication in regs.h 18b1027e5b6e wifi: mt76: mt7915: move mib_stats structure in mt76.h 25ec4b91020e wifi: mt76: mt7996: rely on mib_stats shared definition 6541afa88b3b wifi: mt76: mt7921: rely on mib_stats shared definition eeb60eb9a5a0 wifi: mt76: mt7915: add support for MT7981 [sync with upstream] d5b7e6a3d735 wifi: mt76: mt7921e: report tx retries/failed counts in tx free event f0f19cea6646 wifi: mt76: mt7921: fix skb leak by txs missing in AMSDU edd8a830f6e3 wifi: mt76: add tx_nss histogram to ethtool stats e48235308b3e wifi: mt76: mt7915: accumulate mu-mimo ofdma muru stats a729242363d9 wifi: mt76: mt7921: fix non-PSC channel scan fail 8d52436ee0cd wifi: mt76: mt7921: Support temp sensor d152c8688c14 wifi: mt76: mt7915: disable WFDMA Tx/Rx during SER recovery d07785c344ac wifi: mt76: mt7996: disable WFDMA Tx/Rx during SER recovery 2a19784137f9 wifi: mt76: mt7921: make mt7921_mac_sta_poll static da8e33a15e71 wifi: mt76: mt7915: fix command timeout in AP stop period cc58d5c4a9c9 mt76: mt7996: rely on mt76_sta_stats in mt76_wcid 98a37c82a373 wifi: mt76: mt7921: get rid of MT7921_RESET_TIMEOUT marco ece724cf562b wifi: mt76: mt7996: move radio ctrl commands to proper functions 527cbbc5ede7 wifi: mt76: connac: add support for dsp firmware download 44e323340637 wifi: mt76: mt7996: fix bss wlan_idx when sending bss_info command 63f0053df07a wifi: mt76: mt7996: enable VHT extended NSS BW feature e1bb4ef7b2bb wifi: mt76: connac: add support to set ifs time by mcu command 080ca19cc686 wifi: mt76: mt7996: use correct phy for background radar event 2c163f1812a3 wifi: mt76: mt7996: fix WA event ring size b511a437ace4 wifi: mt76: mt7996: add muru support ece67c98dc1c wifi: mt76: mt7996: increase tx token size 7c2515d85117 wifi: mt76: mt7921e: fix init command fail with enabled device 30706095c566 wifi: mt76: mt7915: move sta_poll_list and sta_poll_lock in mt76_dev b06ed10ee271 wifi: mt76: mt7603: rely on shared sta_poll_list and sta_poll_lock b59bdae339de wifi: mt76: mt7615: rely on shared sta_poll_list and sta_poll_lock 6da2e0e4ef54 wifi: mt76: mt7996: rely on shared sta_poll_list and sta_poll_lock b19d3ad88e8b wifi: mt76: mt7921: rely on shared sta_poll_list and sta_poll_lock 595b033275a3 wifi: mt76: mt7915: move poll_list in mt76_wcid 16fcad171849 wifi: mt76: mt7603: rely on shared poll_list field e19f84091d2e wifi: mt76: mt7615: rely on shared poll_list field b87e4dad1e84 wifi: mt76: mt7996: rely on shared poll_list field 6d7950e258d0 wifi: mt76: mt7921: rely on shared poll_list field f5c5eece5038 wifi: mt76: move ampdu_state in mt76_wcid 7e44467469fe mt76: connac: move more mt7921/mt7915 mac shared code in connac lib 39a70710ddcd wifi: mt76: move rate info in mt76_vif 0dc4326991df wifi: mt76: connac: move connac3 definitions in mt76_connac3_mac.h 29cfabbb4b90 wifi: mt76: connac: add connac3 mac library Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netfilter: fix typo in nf-socket and nf-tproxy kconfigChristian Marangi2023-06-23
| | | | | | | | Fix a typo where the wrong KCONFIG was used and fix selecting the correct kernel config option to use these packages. Fixes: 4f443c885ded ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* mac80211: fix quilt patch corruptionFelix Fietkau2023-06-23
| | | | | Fixes: 9219b0660a91 ("mac80211: fix HE issues with AP_VLAN interfaces") Signed-off-by: Felix Fietkau <nbd@nbd.name>
Powered by cgit, Themed by Ted Yin.