aboutsummaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAge
* rockchip: add NanoPi R4S Enterprise Edition buildTianling Shen2024-02-19
| | | | | | | | | | | FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address) to "enterprise" edition, and it was added as a "new" board in upstream kernel. This patch switched to use that upstreamed dts and removed local EEPROM patch. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* ath79: update WA/XC devices UBNT_VERSION to 8.7.4Martin Garbe2024-02-19
| | | | | | | | | | Ubiquiti WA devices with newer hw version (sold 2023) require UBNT_VERSION to be at least 8.7.4, otherwise the image is rejected. For consistency, also increase version number for XC devices. Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
* rockchip: add NanoPi R2C Plus supportTianling Shen2024-02-19
| | | | | | | | | | | | The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board eMMC flash (8G) included. Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-rockchip: add NanoPi R2C Plus supportTianling Shen2024-02-19
| | | | | | Add support for the FriendlyARM NanoPi R2C Plus. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* qualcommax: backport more changes for ipq6018 and ipq8074Chukun Pan2024-02-19
| | | | | | | | - Mark patches as upstream - Backport more upstream changes - Handle conflicts and refresh patches Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* base-files: sysupgrade: include uci-defaults script disabling servicesRafał Miłecki2024-02-19
| | | | | | | | | | | | | | Disabled services should be kept disabled after sysupgrade. This can be easily handled using a proper uci-defaults script. Extend sysupgrade to check for disabled services, generate uci-defaults script disabling them and include it in backup. Cc: Christian Marangi <ansuelsmth@gmail.com> Cc: Jo-Philipp Wich <jo@mein.io> Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Jo-Philipp Wich <jo@mein.io>
* base-files: sysupgrade: always setup overlay when creating backupRafał Miłecki2024-02-19
| | | | | | | | | | | | | | | | | | | | Setting overlay while creating backup allows including extra files in archive without actually writing them to flash. Right now this feature is limited to /etc/backup/ directory and is used only for including installed_packages.txt. Extend this solution to make it more generic: 1. Always mount overlay while creating backup 2. Overlay whole / to don't limit it to /etc/backup/ This allows including any additional files in backups and adding more sysupgrade features. Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com> Cc: Christian Marangi <ansuelsmth@gmail.com> Cc: Jo-Philipp Wich <jo@mein.io> Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* base-files: sysupgrade: always cleanup after backupsLuiz Angelo Daros de Luca2024-02-19
| | | | | | | | | | When tar was failing, it was exiting immediately. Some files and the tmpfs mount (-k) would remain breaking the next backup attempt. Also remove redundant $? from exit builtin call as exit already returns the last command exit code when called. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* base-files: sysupgrade: do not hide tar errorsLuiz Angelo Daros de Luca2024-02-19
| | | | | | | | | | | | | | | tar stderr was probably discarded only to remove this message: tar: removing leading '/' from member names However, together with that, any other error would also be discarded. It is easier to fix that allowing the error message to be printed. In sysupgrade, the backup file list only uses absolute paths. That way, the solution is to remove the leading '/' from all files (sed) and chdir to / (option -C /) Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DTRafał Miłecki2024-02-19
| | | | | | | It's a standard way of grouping on-SoC hardware blocks and this matches upstream DTS. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: filogic: fix nvmem cell names of the GL.iNet MT-2500Daniel Golle2024-02-19
| | | | | | | Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500. Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)" Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* linux-firmware: intel: add BE200 wifi firmwareJanusz Dziedzic2024-02-18
| | | | | | | Add option to install Intel BE200 firmware required by iwlwifi driver and Wifi7 hardware. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
* imx: remove 5.15 supportKoen Vandeputte2024-02-18
| | | | | | Drop all 5.15 files as 6.1 is the default now Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* imx: switch to kernel 6.1Koen Vandeputte2024-02-18
| | | | | | | I have this kernel running for weeks some on a lot of boards in multiple scenarios Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* kernel: bump 6.1 to 6.1.78John Audia2024-02-18
| | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.78 Manually rebased: bcm27xx/patches-6.1/950-0865-usb-dwc3-Set-DMA-and-coherent-masks-early.patch bcm27xx/patches-6.1/950-0124-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch All other patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, logic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, logic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mvebu: drop kernel 5.15 config and patchesStefan Kalscheuer2024-02-18
| | | | | | With default now being at 6.1 we can remove all 5.15 components. Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* mvebu: switch to kernel 6.1Stefan Kalscheuer2024-02-18
| | | | | | After a few months of testing it's time to move to 6.1 by default. Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
* ca-certificates: update to version 20240203Seo Suchan2024-02-18
| | | | | | Update Mozilla certificate authority bundle to version 2.64 Signed-off-by: Seo Suchan <tjtncks@gmail.com>
* realtek: fix Netgear GS110TPP OEM installBjørn Mork2024-02-18
| | | | | | | | | | | | | | | | | | | | Recent OEM firmware versions test the version number embedded in the uimage "name" header field. The exact restricton is unknown, but "7.0.8.4" seems to be the lowest number accepted on a GS110TPPv1 which already has that version or higher. A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware, and considered both unique enough to identify an OpenWrt image and moderately future proof against OEM version bumps. This change is also boot tested on a GS108Tv3 with "BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)" to verify that it doesn't break boot on older hardware. Link: https://forum.openwrt.org/t/72510/58 Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMCDaniel Golle2024-02-18
| | | | | | | Use nvmem-layout in device tree instead of extracting MAC addresses in userspace. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7981: remove inaccurate compatible stringsDaniel Golle2024-02-18
| | | | | | | Remove more inaccurate compatible strings from various clock controllers of the MT7981 SoC. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7981: prevent system freezes on bootDaniel Golle2024-02-18
| | | | | | | | Import patch to make sure SGM_REG_SEL clock is always enabled as it seems that more registers than just SGMIISYS0 and SGMIISYS1 are depending on that clock being enabled. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: convert GL.iNet MT-6000 to NVMEM-on-MMCDaniel Golle2024-02-18
| | | | | | | Now that we can reference MMC partitions in device tree, use that to get rid of Wi-Fi EEPROM and MAC address setup in userspace. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: nvmem: correctly assign fwnode to MMC block deviceDaniel Golle2024-02-18
| | | | | | | | | | Use device_set_node to make sure OF node gets assigned on block devices to be used as NVMEM providers. While block partitions were already working fine as NVMEM providers, bare block devices such as mmcblk0boot1 will not work without this change. Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* qualcommax: ipq807x: wax630: correct UNIPHY2 MAC modeRobert Marko2024-02-17
| | | | | | | | UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and it does not support using USXGMII at all but rather only SGMII or SGMII+. Tested-by: Kristian Skramstad <kristian+github@83.no> Signed-off-by: Robert Marko <robimarko@gmail.com>
* mediatek: dts: mt7981: fix ethsys clock compatibleDaniel Golle2024-02-17
| | | | | | | | | | Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which results in the wrong clock driver probing on MT7981 with Linux 6.1 and ends up freezing the system once WED is used. Fixes: da970d63fb ("mediatek: switch to Linux version 6.1") Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: replace built-in Aquantia driver with moduleRafał Miłecki2024-02-17
| | | | | | | | | | | | | Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by host system. With built-in drivers this doesn't work in OpenWrt / embeddded as filesystem isn't available during PHY probe. That results in delays like: [ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld [ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110) Switch to module to postpone PHY probe to init state. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* qualcommax: ipq807x: correct PHY mode for AQRRobert Marko2024-02-17
| | | | | | | | | | | | | | Interfaces that have AQR-s attached to them are using USXGMII and not just the default SGMII. This was fine until SSDK added some sanity checking and now on Qnap 301W it would fail with: [ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device [ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14 Since this is not Qnap 301W specific lets fix it subtarget wide by declaring the correct PHY mode for 10G AQR-s. Signed-off-by: Robert Marko <robimarko@gmail.com>
* qualcommax: ipq807x: 301w: correct PHY mode for AQRRobert Marko2024-02-17
| | | | | | | | | | | | | Interfaces that have AQR-s attached to them are using USXGMII and not just the default SGMII. This was fine until SSDK added some sanity checking and now on Qnap 301W it would fail with: [ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device [ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14 So, lets fix 10G AQR ports by declaring the correct PHY mode. Signed-off-by: Robert Marko <robimarko@gmail.com>
* mediatek: mt7622: skip build also for Xiaomi AX6SDaniel Golle2024-02-17
| | | | | | | Also here build fails due to increased kernel size. Fixes: da970d63fb ("mediatek: switch to Linux version 6.1") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* build: align SOURCE path for build system and SDKPaul Spooren2024-02-17
| | | | | | | | | | | | | | | Building a package in the build system or the SDK results in different values for the `SOURCE` property, it's either `packages/<package name>` or `feeds/base/<package name>`. The reason is that the SDK handles `openwrt.git` as an external feed called while the build system contains the *base* packages directly. Since packages created with either method are (ideally) the same (bit for bit), align the content of SOURCE. To do so this commit creates a symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE when building from inside the build system. Signed-off-by: Paul Spooren <mail@aparcar.org>
* wifi-scripts: fix FILS AKM selection with EAP-192Eneas U de Queiroz2024-02-17
| | | | | | Fix netifd hostapd.sh selection of FILS-SHA384 algorithm with eap-192. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* mediatek: mt7622: skip build for MT7622 rfb1 (UBI)Daniel Golle2024-02-17
| | | | | | | | | | Due to increased kernel size the build currently fails if including the MT7622 rfb1 (UBI). Skip it for now until there is a better solution (such as replacing the bootloader and changing the flash layout). Fixes: da970d63fb ("mediatek: switch to Linux version 6.1") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: include kmod-phy-airoha-en8811hDaniel Golle2024-02-17
| | | | | | | | Include the needed Ethernet PHY driver module for the BananaPi R3 mini. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Reported-by: BPI forum user nezar_taima Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lua5.3: backport CVE fixRosen Penev2024-02-17
| | | | | | Also refreshed some patches Signed-off-by: Rosen Penev <rosenp@gmail.com>
* lua: fix CVE-2014-5461Rosen Penev2024-02-17
| | | | | | | | Patch taken from Debian. Refresh patches Signed-off-by: Rosen Penev <rosenp@gmail.com>
* images: append to existing image with ubinize-image build cmdDaniel Golle2024-02-16
| | | | | | | | Let ubinize-image append the ubinized image to the existing image instead of replacing it. Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: fix power on M.2 slotTianling Shen2024-02-16
| | | | | | | | | | One of the pins requiered by M.2 slot is conflict with spi1, however, spi1 seems unused so simply disable it for now, this matches the factory behavior [1]. 1. https://github.com/BPI-SINOVOIP/BPI-R3MINI-OPENWRT-V21.02.3/commit/9bd78779f267a21c04c5bb4d16c32e83aae8d1d3 Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: bpi-r3-mini: bind WLAN LED-s to phy*-ap0Tianling Shen2024-02-16
| | | | | | For showing wlan status. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* mediatek: filogic: bpi-r3-mini: convert to new LED color/function formatTianling Shen2024-02-16
| | | | | | | | | | Conversion to new LED color/function format and drop label format. This was needed previously when the new format wasn't supported by leds.sh functions script. Now that is supported this property can be removed in favor of the new format. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-mediatek: bpi-r3-mini: fix typo in bootmenuDaniel Golle2024-02-16
| | | | | | | Fix typo in eMMC bootmenu. Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: generic: fix the alphabetical order in 02_networkFoica David2024-02-16
| | | | | | | This commit fixes the alphabetical order in 02_network. The 2 deco devices in ath79_setup_interfaces() were in the wrong place. Signed-off-by: Foica David <superh552@gmail.com>
* qualcommax: AW1000: add qca8081 PHY LED configurationChukun Pan2024-02-16
| | | | | | | | Since we can configure the PHY LED of the qca8081, add a configuration for this device. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
* qualcommax: AW1000: sync qca807x PHY dts changesChukun Pan2024-02-16
| | | | | | | | | The dts of Arcadyan AW1000 forgot to convert qca807x PHY to PHY package implementation. This commit fix it. Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Robert Marko <robimarko@gmail.com>
* build: fix opkg flags in rootfsJustin Klaassen2024-02-16
| | | | | | | | | | By default opkg sets the "user" flag when a package is installed, which resulted in most packages in the rootfs having this flag set incorrectly. This patch removes the "user" flag from all installed packages when preparing the rootfs image. Fixes: #14427 Signed-off-by: Justin Klaassen <justin@tidylabs.app>
* mediatek: filogic: bpi-r3-mini: fix generating ubinized imageDaniel Golle2024-02-16
| | | | | | | | Generate ubinized image as ARTIFACT and make use of now available generic 'ubinize-image' build step intended for that purpose. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: bpi-r3-mini: fix NAND flash layoutDaniel Golle2024-02-16
| | | | | | | | Fix NAND flash layout which was out-of-sync with the definition in ARM TrustedFirmware-A which expects UBI to start at 0x200000. Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* scripts: ubinize-image.sh: fix on POSIX shell, allow custom imagesDaniel Golle2024-02-16
| | | | | | | | | | Make sure ubinize-image.sh also works with more simple POSIX Shell and allow creating complete custom images to be used as ARTIFACT/foo.img and thereby allow including uImage.FIT, TF-A FIP and what ever else is required on a specific board. Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt76x8: fix build due to renamed U-Boot binaryDaniel Golle2024-02-16
| | | | | | | | | The U-Boot binary for the RAVPower RP-WD009 has been renamed. In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended. Set that new name also in the image build recipe for that device in order to fix build. Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* imx: update default network config for ventanaTim Harvey2024-02-15
| | | | | | | | update the default network configuration for Gateworks Ventana boards such that the left-most front-panel NIC is WAN and any additional are in LAN bridge Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Powered by cgit, Themed by Ted Yin.