aboutsummaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAge
* base-files: ipcalc.sh: correctly set limit for prefix > 30Leon M. Busch-George2023-09-25
| | | | | | | | For /31 and /32 prefixes, there are only host addresses - no network and broadcast address with all-zero and all-one bits. Reflect this when setting the limit. Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
* base-files: ipcalc.sh: correctly interpret num parameterLeon M. Busch-George2023-09-25
| | | | | | | | The start and end addresses are inclusive. Thus, adding num without substracting one results in num + 1 addresses. Add the substraction and to implement the documented behaviour. Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
* build: replace SourceName with PKG_NAME compile unit nameFlorian Eckert2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the same information is stored at the Packages.manifest in the 'Package:' variable and also additionally in the 'SourceName:' variable. So we have for Packages.manifest for strongswan-charon-cmd: ``` Package: strongswan-charon-cmd Version: 5.9.11-1 SourceName: strongswan-charon-cmd License: GPL-2.0-or-later Section: net ``` This is not correct. Several installable packages are built from the same strongswan source. Therefore it makes more sense that the source name is really the source name. In this case the it is 'strongswan'. After this change the Packages.manifest for strongswan-charon-cmd: ``` Package: strongswan-charon-cmd Version: 5.9.11-1 SourceName: strongswan License: GPL-2.0-or-later Section: net ``` In summary. The 'Package' name is the name of the package to be installed on the target system. The 'SourceName' is the compile unit from which the package was build from. This must be the same for all installable packages built from the same compile unit. This commit fixes that. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* ipq40xx: wpj428: panic on squashfs error to work around boot limboLeon M. Busch-George2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Apparently, a few ipq40xx devices have sporadic problems when reading the flash over SPI. When that happens, the result of the faulty SPI read is cached and it isn't re-attempted. Depending on when it happens, the router either panics and reboots or is left in a partially broken state (an application wont start). The data on the flash is alright. This wasn't the case with Openwrt with Linux < 5.x but I wasn't able to work out which software change was responsible. Github user karlpip created a patch for testing that disabled the cache entirely and added logs. Typically, only one or two SPI operations fail at a time: [689200.631152] spi-nor spi0.0: SPI transfer failed: -110 [689200.631280] spi_master spi0: failed to transfer one message from queue [689200.635369] jffs2: Write of 68 bytes at 0x00ffccf4 failed. returned -110, retlen 0 [689200.642014] jffs2: Not marking the space at 0x00ffccf4 as dirty because the flash driver returned retlen zero Because reads aren't re-attempted, squashfs can't recover: [3171844.279235] SQUASHFS error: Failed to read block 0x2bb912: -5 [3171844.279284] SQUASHFS error: Unable to read fragment cache entry [2bb912] [3171844.283980] SQUASHFS error: Unable to read page, block 2bb912, size 14e6c [3171844.291650] SQUASHFS error: Unable to read fragment cache entry [2bb912] [3171844.297831] SQUASHFS error: Unable to read page, block 2bb912, size 14e6c I assume there to be some kind of underlying electrical problem because, in my experience, this happens a lot more when PoE is used. NoTengoBattery has made an in-depth investigation: https://forum.openwrt.org/t/patch-squashfs-data-probably-corrupt/70480 .. and created a patch that evicts the page cache and retries reading: https://github.com/NoTengoBattery/openwrt/blob/linksys-ea6350v3-mastertrack/target/linux/ipq40xx/patches-5.4/9996-fs_squashfs_improve_squashfs_error_resistance.patch The patch also works well with the WPJ428 but NoTengoBattery didn't try to upstream it ("This is not the solution that should be used"). In 2020, I tried and failed to create a working patch that prevents faulty pages to be cached in the first place. Because I needed a solution, I backported "squashfs: add option to panic on errors " (10dde05b89980ef) which has since become available in Openwrt. The 'error=panic' option has been tested on a fleet of multiple hundred WPJ428s over multiple years. Without this patch, devices regularly went into 'limbo' on reboot or update and required a manual reboot. Devices with this patch don't. I was initially concerned that the kernel panic would leave devices with a real corrupted data but I haven't seen a case of actual corruption since (outside of people turning off the power during upgrades). The WPJ428 is the only device I tested this patch on - others might also benefit. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
* mediatek: add support for Buffalo WSR-3200AX4SINAGAKI Hiroshi2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WSR-3200AX4S is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specification: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915 - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/5x (2x: buttons, 3x: slide-switches) - UART : through-hole on PCB (J4) - assignment: 3.3V, GND, TX, RX from tri-angle marking - settings : 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory.bin image: 1. Boot WSR-3200AX4S with "Router" mode 2. Access to "http://192.168.11.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("更新実行") button 4. Wait ~120 seconds to complete flashing Note: - This device has 2x OS images on flash. The first one will always be used for booting and the secondary is for backup. - This support generates multiple factory*.bin image: - factory.bin : for flashing from OEM WebUI - factory-uboot.bin: for flashing from U-Boot or clean installation via sysupgrade (don't use for normal sysupgrade) Known issues: - Wi-Fi MAC addresses won't be applied to each adapter. MAC Addresses: LAN : C4:3C:EA:xx:xx:60 (board_data, mac (text)) WAN : C4:3C:EA:xx:xx:60 (board_data, mac (text)) 2.4 GHz: C4:3C:EA:xx:xx:61 5 GHz : C4:3C:EA:xx:xx:68 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: separate dts/dtsi for Buffalo WSR seriesINAGAKI Hiroshi2023-09-24
| | | | | | | Separate dts/dtsi from the dts of Buffalo WSR-2533DHP2 to prepare adding suppport for WSR-3200AX4S. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: expand kernel size to 6MiB for WSR-2533DHP2INAGAKI Hiroshi2023-09-24
| | | | | | | | | | Expand kernel partition size on WSR-2533DHP2 for the kernel larger than 4 MiB. To prevent upgrading from old firmware before this commit, bump the compat version to 1.1 and add a message for forced sysupgrade using factory-uboot.bin image. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: merge trx helpers in image/mt7622.mkINAGAKI Hiroshi2023-09-24
| | | | | | | Merge similar helpers of trx image generation, "buffalo-kernel-trx" and "trx-nand". Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: drop pwm7_pins from Buffalo WSR-2533DHP2INAGAKI Hiroshi2023-09-24
| | | | | | | | | | | | | | MediaTek MT7622 doesn't support ch7 of PWM and pinctrl groups were dropped from driver source[0]. So pwm7-related groups are unavailable now, then, kernel shows a warning. [ 0.370264] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm" Drop that pinmux from pinctrl node. [0]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/pinctrl/mediatek/pinctrl-mt7622.c?id=57972641810a97566ffd13e4be3f6a66d61eb3b5 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: add label-mac-device for Buffalo WSR-2533DHP2INAGAKI Hiroshi2023-09-24
| | | | | | Add label-mac-device with "&gmac0" phandle for Buffalo WSR-2533DHP2. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: update NVMEM bindings for Buffalo WSR-2533DHP2INAGAKI Hiroshi2023-09-24
| | | | | | | Update NVMEM-related nodes and use newer binding for MAC addresses on Buffalo WSR-2533DHP2. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: update LED/Key bindings for Buffalo WSR-2533DHP2INAGAKI Hiroshi2023-09-24
| | | | | | | | | | | | | | | | Update LED and key nodes with newer DeviceTree bindings for WSR-2533DHP2. - LED - use led-[0-9] for node name of LEDs - add "color" and "function" properties - drop default-state = "on" from green:power LED - this LED will be turned on by led-running alias - key - drop unnecessary poll-interval property - use key-[0-9] for node name of keys Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* sunxi: generalize top-level BOARDNAME and update suported SoCsSebastian Pflieger2023-09-24
| | | | | | Allwinner created to may SoC variants to list them all at top-level. Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
* ipq806x: sync config-6.1 with latest kernelGlen Lee2023-09-24
| | | | | Ran "make kernel_oldconfig" to generate Signed-off-by: Glen Lee <g2lee@yahoo.com>
* mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)Elbert Mai2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti U6+ is a dual-band WiFi 6 PoE access point. It is a drop-in upgrade of the U6 lite. Specifications --- - SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz - RAM: 256 MB DDR3-2133 RAM - Flash: 16 MB SPI NOR and 4 GB eMMC - LAN: 1x Gigabit Ethernet with 802.3af/at support - WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6 - LEDs: 1x blue and 1x white - Buttons: 1x reset button Installation --- 1. Power device using a PoE injector or switch 2. Connect via Ethernet to the device with static IP 192.168.1.2 3. SSH into the device with password: ubnt $ ssh ubnt@192.168.1.20 4. Unlock kernel partitions for writing $ echo 5edfacbf > /proc/ubnthal/.uf 5. Confirm correct partitions $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent PARTNAME=kernel0 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent PARTNAME=kernel1 $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent PARTNAME=bs 6. Set and confirm bootloader environment $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd_real "run boot_openwrt" $ fw_printenv 7. Copy sysupgrade image to /tmp/openwrt.bin via scp 8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6 $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7 9. Ensure device boots from mmcblk0p6 $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8 10. Reboot the device $ reboot Signed-off-by: Elbert Mai <code@elbertmai.com> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* arm-trusted-firmware-sunxi: update to version 2.9Sebastian Pflieger2023-09-24
| | | | | | | | | - detect die revision used in variants of the Allwinner H616 SoC (H313, T507) - support for H6 boards without PMIC Tested on Pine64+ and Orange PI Zero2 Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
* ramips: fix Mercusys MR70X LAN port assignmentsAndreas Böhler2023-09-24
| | | | | | | | | A bug report in the forum found that the MR70X lists four LAN ports in LuCI while it has only three. This adds the device to the network setup file to fix the issue. Identified-by: Forum User "Lexeyko" Signed-off-by: Andreas Böhler <dev@aboehler.at>
* lldpd: add lldp_syscapabilities config optionSebastian Pflieger2023-09-24
| | | | | | | allow to overwrite the detected system capabilities e.g. if devices does not operate as bridge. Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
* ipq807x: add support for Netgear WAX620Kristian Skramstad2023-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ``` Specifications: * CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz * RAM: 1 GiB of DDR4 600 MHz * Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC) * 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz * UART: Two 4-pin unpopulated headers under the LEDs. Use the header closest to LED 4 and 5. They are marked with a white stroke. TX RX GND, beginning from "4". 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081) Wlan: * 4x4 in 2.4GHz: 802.11b/g/n/ax * 4x4 in 5.0GHz: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz) Power: * PoE+ 802.3at/af 25.5W * DC 12V 2.5A ``` ``` Note: The OpenWrt image is setup with DHCP and not a static IP. 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Signed-off-by: Kristian Skramstad <kristian+github@83.no>
* armsr: ensure kmod-fs-vfat is selected for mounting ESPMathew McBride2023-09-24
| | | | | | | | vfat support is needed to mount the EFI System Partition (ESP) during sysupgrade. If it is not available, the sysupgrade process will not complete Signed-off-by: Mathew McBride <matt@traverse.com.au>
* ccache: add missing \Oskari Rauta2023-09-24
| | | | | | -DREDIS_STORAGE_BACKEND=OFF option is ignored due to missing \ Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
* kernel: bump 6.1 to 6.1.55John Audia2023-09-24
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.55 All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* openssl: update to 3.0.11Ivan Pavlov2023-09-24
| | | | | | | Changes between 3.0.10 and 3.0.11 [19 Sep 2023] * Fix POLY1305 MAC implementation corrupting XMM registers on Windows. ([CVE-2023-4807]) Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
* ramips: add support for WAVLINK WL-WN573HX1Sijia Huang2023-09-24
| | | | | | | | | | | | | | | | | | | | Hardware -------- Specifications: - Device: WAVLINK WL-WN573HX1 Outdoor AP - SoC: MT7621AT - Flash: 16MB - RAM: 256MB - Switch:1 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x STATUS (blue, configurable) 1x LAN (green) Product link: https://www.wavlink.com/en_us/product/WL-WN573HX1.html Signed-off-by: Sijia Huang <engineer31@win-star.com>
* kernel: bump 6.1 to 6.1.54John Audia2023-09-23
| | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.54 Removed upstreamed: generic/backport-6.1/020-v6.3-02-UPSTREAM-mm-multi-gen-LRU-rename-lrugen-lists-to-lru.patch[1] ipq806x/patches-6.1/140-v6.5-hwspinlock-qcom-add-missing-regmap-config-for-SFPB-M.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.54&id=a73d04c460521e45f257d28d73df096e41ece324 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.54&id=e93bc372dbc0bde133c854c03502a95617041972 Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.53John Audia2023-09-23
| | | | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.53 Removed upstreamed: bcm53xx/patches-6.1/032-v6.6-0005-ARM-dts-BCM53573-Drop-nonexistent-usb-cells.patch[1] bcm53xx/patches-6.1/032-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[2] bcm53xx/patches-6.1/032-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[3] bcm53xx/patches-6.1/032-v6.6-0011-ARM-dts-BCM53573-Fix-Tenda-AC9-switch-CPU-port.patch[4] All other patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=ee1d740374aa73fb32857685eb05167ad87458cf 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=ab5154ae26c446136827451e907db45d7b92a76f 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=f5ff6897094fa161be55786cb9e5d5b1bf7a9049 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=0ef736fec61422794c4a991d46c4ec212b01d8d1 Signed-off-by: John Audia <therealgraysky@proton.me>
* config-6.1: disable CONFIG_VIDEO_CAMERA_SENSORJohn Audia2023-09-23
| | | | | | | Disable new ksym globally as it is unconditionally selecting symbols. See: https://github.com/torvalds/linux/commit/7d3c7d2a2914e10bec3b9cdacdadb8e1f65f715a Signed-off-by: John Audia <therealgraysky@proton.me>
* mac80211: rt2x00: fix MT7620 low RSSI issueShiji Yang2023-09-23
| | | | | | | | | | | Introducing SoC specific RSSI base value to fix the low RSSI issue on MT7620. With this fix[1], the RSSI value reported by MT7620 will increase by 10 dB. [1] https://lore.kernel.org/linux-wireless/TYAP286MB031571CDB146C414A908A66DBCFEA@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM/ Fixes: https://github.com/openwrt/openwrt/issues/11036 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* hostapd: fix patch rebase after a crash fixFelix Fietkau2023-09-22
| | | | | | | | The patch refresh accidentally moved the hostapd_ucode_free_iface call to the wrong function Fixes: e9722aef9e84 ("hostapd: fix a crash when disabling an interface during channel list update") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/libressl: update to version 3.7.3Josef Schlehofer2023-09-22
| | | | | | | Release notes: https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.7.3-relnotes.txt Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* hostapd: fix wpa_supplicant bringup with non-nl80211 driversFelix Fietkau2023-09-22
| | | | | | Needed for wired 802.1x Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add build for MT7981 RFBDaniel Golle2023-09-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add build for the MTK3943 reference board for MT7981B+MT7976C. **Hardware specification:** - SoC: MediaTek MT7981B 2x A53 - Flash: various options - RAM: 256MB DDR3 - Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch EITHER 1 x 10/100/1000 Mbps built-in PHY OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C - Switch: MediaTek MT7531AE - WiFi: MediaTek MT7976C - Button: RST, WPS **Flash instructions for SPIM-NAND:** - write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition - write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition - erase 'ubi' partition - reset board - create ubootenv and ubootenv2 UBI volumes in U-Boot - edit environment and set bootcmd, e.g. setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1' setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf' - load initramfs image via TFTP: setenv serverip 192.168.1.254 setenv ipaddr 192.168.1.1 setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb saveenv ; saveenv tftpboot bootm $loadaddr#$bootconf - Now use sysupgrade to write OpenWrt firmware to flash. SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image is also being generated. However, as the board I've been provided only comes with SPIM-NAND all other boot media are untested. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: add build for mt7981 rfbDaniel Golle2023-09-21
| | | | | | | Improve and package builds for various boot media configurations of the MediaTek MT7981 reference board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: fix copy&paste error in MakefileDaniel Golle2023-09-21
| | | | | | | | | When adding builds for MT7981 the related Makefile sections for MT7986 have apparently been copied, but in one instance the rename from 7986 to 7981 has been omitted. Fix that now. Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: serial: 8250_mtk: track busclk state to avoid bus errorDaniel Golle2023-09-21
| | | | | | | | UARTs not used as boot console are currently broken on some MediaTek targets due to register access depending on the bus clock being enabled. Add patch to make sure this dependency is always met. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mpc85xx: correct WS-AP3715i eth LED assignmentDavid Bauer2023-09-21
| | | | | | | Ethernet LED assignments were incorrectly swapped. Fix the assignment logic so the correct LED is illuminated for the LAN LEDs. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: add missing NULL pointer check in uc_hostapd_iface_stopFelix Fietkau2023-09-20
| | | | | | Avoid crashing if the interface has already been removed Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq4019: add support for ZTE MF282 Plus aka DreiTubeAndreas Böhler2023-09-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF282 Plus is a LTE router used (exclusively?) by the network operator "3". It is very similar to the MF286/MF287 but in the form factor of the MF282. Specifications ============== SoC: IPQ4019 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 1x GBit LAN LTE: ZTE Cat6 WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config WiFi 1: from config + 1 WiFi 2: from config + 2 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x84000000 openwrt.bin bootm 0x84000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m9 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd9 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd9 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock9 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 9 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to the MF286R, it provides an RNDIS interface and an AT interface. Other Notes =========== There is one GPIO Switch "Power button blocker" which, if enabled, does not trigger a reset of the SoC if the modem reboots. If disabled, the SoC is rebooted along with the modem. The modem can be rebooted via the exported GPIO "modem-reset" in /sys/class/gpio. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* kernel: bump 5.15 to 5.15.132John Audia2023-09-20
| | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132 Removed upstreamed: bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1] bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2] bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=b35f3ca1877e024887df205ede952863d65dad36 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=2840d9b9c8750be270fb1153ccd5b983cbb5d592 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=f086e859ddc252c32f0438edff241859c0f022ce Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* hostapd: fix a crash when disabling an interface during channel list updateFelix Fietkau2023-09-20
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* toolchain: assign PKG_CPE_IDAlexander Couzens2023-09-19
| | | | | | | | | The PKG_CPE_ID links to NIST CPE version 2.2. Assign PKG_CPE_ID to all remaining package which have a CPE ID. Not every package has a CPE id. Related: https://github.com/openwrt/packages/issues/8534 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* tools: assign PKG_CPE_IDAlexander Couzens2023-09-19
| | | | | | | | | The PKG_CPE_ID links to NIST CPE version 2.2. Assign PKG_CPE_ID to all remaining tools which have a CPE ID. Not every tool has CPE id. Related: https://github.com/openwrt/packages/issues/8534 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* packages: assign PKG_CPE_ID for all missing packagesAlexander Couzens2023-09-19
| | | | | | | | | The PKG_CPE_ID links to NIST CPE version 2.2. Assign PKG_CPE_ID to all remaining package which have a CPE ID. Not every package has CPE id. Related: https://github.com/openwrt/packages/issues/8534 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* sdk: add cpupower to userspace sourcesJohn Audia2023-09-19
| | | | | | | For https://github.com/openwrt/packages/pull/21533 to be merged, this source tree is needed to be included. Signed-off-by: John Audia <therealgraysky@proton.me>
* mvebu: eDPU: add support for version with external switchRobert Marko2023-09-19
| | | | | | | | | | | New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP cage and G.hn IC instead of connecting them directly to the ethernet controllers. The same image can be used on both versions as U-Boot will enable the switch node and disable the unused ethernet controller. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* uboot-mvebu: eDPU: add support for version with external switchRobert Marko2023-09-19
| | | | | | | | | | | | | New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP cage and G.hn IC instead of connecting them directly to the ethernet controllers. In order to use the same image for both boards, U-Boot is responsible for detecting the revision and enabling/disabling DTS nodes. So, to make it easy for users, lets add the pending U-Boot patches to build in OpenWrt. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* generic: 6.1: backport support for Marvell 88E6361 switchRobert Marko2023-09-19
| | | | | | | New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets backport it from kernel 6.5. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* generic: 5.15: backport support for Marvell 88E6361 switchRobert Marko2023-09-19
| | | | | | | | | | | | New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets backport it from kernel 6.5. Since 5.15 doesnt have phylink_get_caps I had to modify the backport to use the old mv88e6393x_phylink_validate instead. I had to fixup one more instance of port_max_speed_mode as well that is not present in 6.5. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* netifd: update to the latest versionFelix Fietkau2023-09-19
| | | | | | 7a58b995fdbe wireless: update prev_config on SET_DATA notify Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: use phy name for hostapd interfaces instead of first-bss ifnameFelix Fietkau2023-09-19
| | | | | | Improves reliability in error handling Signed-off-by: Felix Fietkau <nbd@nbd.name>
Powered by cgit, Themed by Ted Yin.