aboutsummaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAge
...
* mvebu: cortexa72: enable USB PHYTomasz Maciej Nowak2023-09-08
| | | | | | | | | Since kernel 5.13 this is needed to enable USB ports on all devices in subtarget. Previously TF-A and COMPHY driver might have set up this PHY, but not anymore. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Robert Marko <robimarko@gmail.com>
* mvebu: refresh 6.1 configsTomasz Maciej Nowak2023-09-08
| | | | | | | This should be a part of kernel major bump. Fortunately it didn't stall compilation, so no fixes tag. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mediatek: add support for Cetron CT3003Patricia Lee2023-09-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **Hardware specification:** - SoC: MediaTek MT7981B 2x A53 - Flash: ESMT F50L1G41LB 128MB - RAM: Nanya NT5CC128M16JR-EK 256MB - Ethernet: 4 x 10/100/1000 Mbps - Switch: MediaTek MT7531AE - WiFi: MediaTek MT7976C - Button: Reset, Mesh - Power: DC 12V 1A - UART: 3.3v, 115200n8 | Layout: | | :-------- | | <Antenna> | | VCC | | GND | | Tx | | Rx | **Flash instructions:** 1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`. 2. Upload the `factory.bin` using the device's Web interface. 3. Click the upgrade button and wait for the process to finish. 4. Access the OpenWrt interface using the same password. 5. Use the 'Restore' function to reset the firmware to its initial state. **Notes:** If you plan to recovery the stock firmware in the future, it's advisable to connect the device via the serial port and enter failsafe mode to back up all the MTD partitions before proceeding the steps above. Signed-off-by: Patricia Lee <patricialee320@gmail.com>
* kernel: bump 5.15 to 5.15.131John Audia2023-09-08
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.131 All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: use kernel 6.1 as defaultDavid Bauer2023-09-08
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: enable variable sector size erasure for generic subtargetShiji Yang2023-09-08
| | | | | | | Make use of minor sector size (4k) erasure on supported flash chips to improve spi read/write performance. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: backport gpio immutable irq_chip supportShiji Yang2023-09-08
| | | | | | | This patch converts the driver to immutable irq-chip, which can silence some gpio warnings. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: ignore the abused interrupt-map on PCIe nodeShiji Yang2023-09-08
| | | | | | | | | | | | | | | | | ath79 PCIe interrupt controller has stopped working correctly. This is because the DT exposing a non-sensical interrupt-map property, and their drivers relying on the kernel ignoring this property[1]. This patch fixes the PCIe init error: ath9k 0000:00:00.0: of_irq_parse_pci: failed with rc=-14 Notice: This is just a workaround, not a fix. PCIe driver and related dts node need to be rewritten. [1] https://lore.kernel.org/all/20211201114102.13446-1-maz@kernel.org/ Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: fix ethernet driver build errors on kernel 6.1Shiji Yang2023-09-08
| | | | | | | Some net APIs have changed on the new kernel. Update them to fix compile errors. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: refresh patches and configs to introduce kernel 6.1 supportShiji Yang2023-09-08
| | | | | | | | | | | | | | | | | | | All kernel configs are refreshed by 'make kernel_oldconfig CONFIG_TARGET=target' and 'make kernel_oldconfig CONFIG_TARGET=subtarget'. upstreamed patches: 010-v5.17-spi-ar934x-fix-transfer-and-word-delays.patch 011-v5.17-spi-ar934x-fix-transfer-size.patch 020-v5.18-spi-ath79-Implement-the-spi_mem-interface.patch 030-v5.18-ath79-add-support-for-booting-QCN550x.patch build and run tested on: ath79/generic/ar7241 ath79/generic/qca9563 ath79/nand/ar9344 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: copy patches and kernel config from 5.15 to 6.1Shiji Yang2023-09-08
| | | | | | This is preparation for kernel 6.1 support. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: rename and sort patches by OpenWrt naming rulesShiji Yang2023-09-08
| | | | | | | | | | The patches in the ath79 target have not been sorted for a long time and they are very chaotic now. This patch sorts them again according to the OpenWrt naming rules[1], so that we can better manage them. [1] https://openwrt.org/docs/guide-developer/toolchain/use-patches-with-buildsystem#naming_patches Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add missing symbols by refreshing kernel configsShiji Yang2023-09-08
| | | | | | | | | Some symbols are outdated or missing due to daily kernel bumps. It's better to re-add them. All configs are automatically refreshed by 'make kernel_oldconfig CONFIG_TARGET=taget' and 'make kernel_oldconfig CONFIG_TARGET=subtarget' Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: switch back to fw_devlink=permissiveRafał Miłecki2023-09-05
| | | | | | | | | | | | | | | This reverts commit 5356462ce54734afd32fce83ad118c58cfeb2a55. Kernel switching to fw_devlink=on as default broke probing some devices. Revert it until we get a proper fix. It seemed that mtd OF_POPULATED hack resolved probing issues but apparently not all of them. We got reports about reading MAC using NVMEM not working and USB controllers not working. Ref: #10232 Fixes: #13412 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: fix the name of buswidth to bus-widthChen Minqiang2023-09-05
| | | | | | | | | | | Fix the issue of dts buswidth cannot be applied properly with spi driver. Fix the name of buswidth to bus-width in dts in order to fit the format in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be parsed properly. [1] Documentation/devicetree/bindings/spi/spi-controller.yaml Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* rockchip: add support for Radxa ROCK Pi EJayantajit Gogoi2023-09-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for Radxa ROCK Pi E, rockchip rk3328 board. Specification: - CPU: Rockchip RK3328 64-bit Quad-core - RAM: DDR3 256MB ~ 2GB - Network: 1 x 10/100/1000M Ethernet 1 x 10/100M Ethernet - Storage: 1 x MicroSD Slot 1 x eMMC Module Slot - USB Host/OTG: 1 x USB3.0 Type A HOST 1 x USB2.0 HOST (40-pin pin-header) - Wireless RTL8723DU/RTL8821CU - Debug Serial: 1500000 baud at UART2 ( 40-pin pin-header) - Power Supply: Type-C 5V Optionally PoE Installation: - Write image to SD Card or EMMC with dd - Boot ROCK Pi E from the SD Card Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
* uboot-rockchip: add suport for Radxa ROCK Pi EJayantajit Gogoi2023-09-05
| | | | | | | | | | | | | | | | | | | | | | | | | Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board. Add pre-built files to fix swig dependencies. Specification: - CPU: Rockchip RK3328 64-bit Quad-core - RAM: DDR3 256MB ~ 2GB - Network: 1 x 10/100/1000M Ethernet 1 x 10/100M Ethernet - USB Host: 1 x USB3.0 Type A HOST 1 x USB2.0 OTG (40-pin pin-header) - Wireless: RTL8723DU/RTL8821CU - Power Supply: Type-C 5V Installation: - Write image to SD Card or EMMC with dd - Boot ROCK Pi E from the SD Card Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
* kernel: backport support for renaming netdevs while upFelix Fietkau2023-09-04
| | | | | | Will be used in upcoming hostapd changes Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: compress kernel for Magic 2 WiFi nextThomas Bong2023-09-03
| | | | | | | | | The bootcmd limits the kernel to 4 MiB which is exceeded when using Device/FitImage. Device/FitzImage reduces the size to around 3 MiB. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
* ipq40xx: convert devolo Magic 2 WiFi next to DSAThomas Bong2023-09-03
| | | | | | | | | | Renamed the interfaces to match the other devices. Name the interface connected to the builtin G.hn chip 'ghn'. This might toggle at runtime while the G.hn chip is in the bootloader. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
* tools/cmake: update to 3.27.4Hannu Nyman2023-09-03
| | | | | | | Update cmake to 3.27.4 No patch refresh needed. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* wireless-regdb: update to 2023.09.01Yuu Toriyama2023-09-03
| | | | | | | | | | | Changes: 9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH) 111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines ae1421f wireless-regdb: Update regulatory info for Türkiye (TR) 20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023 991b1ef wireless-regdb: update regulatory database based on preceding changes Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
* mvebu: add reset delays of PHYs for Fortinet FortiGate 50EINAGAKI Hiroshi2023-09-03
| | | | | | | | | | Add reset-(de)assert-us to ethernet PHYs on Fortinet FortiGate 50E to solve instability after HW resetting of PHYs. (ex.: restarting "network" service, etc...) Fixes: #13391 Fixes: 102dc5a62506 ("mvebu: add support for Fortinet FortiGate 50E") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 6.1 to 6.1.51John Audia2023-09-03
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.51 No patches needed a rebased. Update to checksum only. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.130John Audia2023-09-03
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.130 No patches needed a rebased. Update to checksum only. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* hostapd: allow adding initial AP without breaking STA interface connectionFelix Fietkau2023-09-03
| | | | | | | | | | When switching from a STA-only configuration to AP+STA on the same phy, the STA was previously restarted in order to notify hostapd of the new frequency, which might not match the AP configuration. Fix the STA restart by querying the operating frequency from within hostapd when bringing up the AP. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: fix config change detection on boolean valuesFelix Fietkau2023-09-03
| | | | | | Check for null instead of truish value Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: fix parsing HT secondary channel offsetFelix Fietkau2023-09-02
| | | | | | It returned the wrong value when using HT40- Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: reset center_seg0_idx for 2.4 GHzFelix Fietkau2023-09-02
| | | | | | Fixes 40 MHz channel bandwidth on 2.4 GHz AP+STA Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: use proper helper functions for setting seg0/seg1 idx and chwidthFelix Fietkau2023-09-02
| | | | | | Simplifies code and removes #ifdef statements Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: fix sysupgrade error for WR30UHank Moretti2023-09-01
| | | | | | | | | The NMBM-Enabled layout did not use fit image, it just need default process. So it was been removed in platform.sh. It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm. Signed-off-by: Hank Moretti <mchank9999@gmail.com>
* scripts/download.pl: remove stale GNOME download sitesHannu Nyman2023-09-01
| | | | | | | | | Remove stale sites from @GNOME alias: * remove 2 sites that have stale 3 years old content * remove 2 sites that have dropped GNOME * convert 2 sites from FTP to HTTP Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* kernel: bump 6.1 to 6.1.50John Audia2023-09-01
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.50 All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod, ipq806x/R7800 Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod, ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.129John Audia2023-09-01
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.129 All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* scripts/package-metadata.pl: strip already selected conditions from dependenciesFelix Fietkau2023-09-01
| | | | | | | | When a dependency is pulled in via conditional depends, and the condition is already selected earlier in the chain, drop the condition. This avoids some corner cases that trigger recursive dependencies. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "scripts/package-metadata.pl: fix handling transitive conditional ↵Felix Fietkau2023-09-01
| | | | | | | | | | dependencies" This reverts commit 6c3eff9dd8bb8d0f268e8a0dbedbc6a33bdac796. This appears to cause some regressions in generated config. Will be replaced with a fixed version later Signed-off-by: Felix Fietkau <nbd@nbd.name>
* scripts/package-metadata.pl: sort dependency keysFelix Fietkau2023-09-01
| | | | | | | This makes it easier to keep track of changes in the generated output, when the script is modified Signed-off-by: Felix Fietkau <nbd@nbd.name>
* firewall4: update to the latest versionFelix Fietkau2023-09-01
| | | | | | | | | 23a434d0d15d tests: fix expected test output 840ccdeeabce fw4: avoid emitting invalid rule jump targets 20da9933fd7e fw4: fix another instance of invalid rule jump targets 598d9fbb5179 fw4: remove special cases around hw flow offloading Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: allow adding devices without hw offload to a hw flowtableFelix Fietkau2023-09-01
| | | | | | This allows supporting a mix of devices with or without hw offloading support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* scripts/package-metadata.pl: fix handling transitive conditional dependenciesFelix Fietkau2023-09-01
| | | | | | | | | | When a package foo depends on PACKAGE_foo:bar (in order to make build dependencies conditional), tracking transitive dependencies can fail because the internal seen flag is checked/set before eliminating the fake conditional dependency. This can show up as a depends on not properly turned into a select further down in the dependency chain Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: remove cfg80211 dependencyFelix Fietkau2023-09-01
| | | | | | Always enable nl80211 driver support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm53xx: store a copy of NVRAM content in NVMEM driverRafał Miłecki2023-09-01
| | | | | | | | This stops NVMEM driver from using MMIO access past booting and messing with NAND controller state. Link: https://forum.openwrt.org/t/asus-rt-ac88u-hw-a6-broken-in-22-03-3/147882 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* netifd: update to latest git HEADDaniel Golle2023-09-01
| | | | | | 1a07f1dff32b make_ethtool_modes_h.sh: apply anti-bashism Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* netifd: update to latest git HEADDaniel Golle2023-08-31
| | | | | | | | | | | | | | | f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API Fixes AN announcement for speeds beyond 1 GBit/s. Adds new UCI options for Ethernet devices: - autoneg: switch on or off auto-negotiation - pause: if set to 0, do not announce symmetric flow control capability - asym_pause: if set to 0, do not announce asymmetric flow control capability. - rxpause: if set overrides AN and forces RX pause accordingly - txpause: if set overrides AN and forces TX pause accordingly Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: set DEVICE_DTC_ADDR for BPi-R64Daniel Golle2023-08-31
| | | | | | | | Relocating the device tree is required for being apply to apply device tree overylay at boot. Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: select libopenssl-legacy for openssl variantsFelix Fietkau2023-08-31
| | | | | | Without it, a lot of authentication modes fail without obvious error messages Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: remove eap-eap192 auth type valueFelix Fietkau2023-08-31
| | | | | | It is no longer used Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netifd: update to the latest versionFelix Fietkau2023-08-31
| | | | | | | | | | | | | | | | | | | db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support Support the following values for the different WPA3 Enterprise modes: - wpa3-mixed: WPA3 Enterprise transitional mode This supports EAP with both SHA1 and SHA-256, with optional MFP - wpa3: WPA3 Enterprise only mode This supports only SHA256 with mandatory MFP - wpa3-192: WPA3 Enterprise with mandatory 192 bit support This uses only GCMP-256 ciphers Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode. It seems that even leaving in optional 192 bit support breaks auth on some clients, including iOS devices. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: support eap-eap2 and eap2 auth_type valuesFelix Fietkau2023-08-31
| | | | | | | WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256 WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: fix FILS key mgmt type for WPA3 Enterprise 192 bitFelix Fietkau2023-08-31
| | | | | | Use the SHA384 variant to account for longer keys with more security Signed-off-by: Felix Fietkau <nbd@nbd.name>
Powered by cgit, Themed by Ted Yin.